Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MaxxECU standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 4

Removed text is struck through; added text is highlighted.

MaxxECU RACE — Eight-cylinder sequential ECU with eight peak-and-hold injectors, electronic throttle, knock inputs and eight thermocouple inputs. MaxxECU product information.

MaxxECU RACE, manufacturer product image: MaxxECU. Used with permission.

Model identification and capabilities

The manufacturer lists eight ignition outputs, nine low-driving auxiliary outputs, two 12 V driving outputs and four motor outputs. Built-in features include a 400 kPa MAP sensor, wideband lambda controller and two knock inputs. Up to twelve cylinders can be controlled with wasted-spark ignition, depending on configuration. Manufacturer specification; MaxxECU model comparison.

Sequential cylinders, maximum8Injector outputs8 peak-and-holdIgnition outputs8ConfigurationMTune; check the release appropriate to the ECU and hardware revision

ProcessorThe manufacturer product page lists an ARM Cortex-M3 main processor running at 120 MHz, with three further processors handling the trigger, injectors and knock detection (manufacturer specification). The specific microcontroller part number is not published.

Identification and installation

This is the original RACE, not GEN2 RACE. Use the model and hardware revision to select the wiring diagram; the manufacturer identifies RACE H2O as a separate water-protected version.

Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.

Connector and pinout

Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.

PositionManufacturer functionNotesA1GPO 5A2IGN 1A3IGN 2A4GPO 8/TACHO660ohm pullupB1GPO 6B2IGN 3B3IGN 4B4GPO 1C1GPO 7C2IGN 5C3IGN 6C4GPO 2D1WBO2 Heater-D2IGN 7D3IGN 8D4GPO 3E1CAN HE2CAN LE3GND ShieldE4GPO 4F1CLTF2IATF3WBO2 VREFF4WBO2 VSG1+5V sensor supply(peak 0.5A, max 150mA)G2TPS/AING3WBO2 IPG4WBO2 RCALH1Sensor GNDH2Trigger GNDH3TRIGGERH4HOMEJ1AIN 1 (Temperature)J2AIN 2 (Temperature)J3AIN 3 (0-5V)J4AIN 4 (0-5V)K1INJ 1K2INJ 2K3DIN/VR 1K4DIN/VR 2L1INJ 8L2INJ 7L3INJ 6L4Engine GNDM1INJ 3M2INJ 4M3INJ 5M4+12V ECU power supply

RACE connector 2

From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.

PositionManufacturer functionNotesA1egt 5+A2egt 6+A3egt 7+A4egt 8+B1egt 5-B2egt 6-B3egt 7-B4egt 8-C1EGT 1 +C2EGT 2+C3EGT 3+C4EGT 4+D1EGT 1-D2EGT 2-D3EGT 3-D4EGT 4-E1KNOCK GNDE2Knock 1E3knock 2E4AIN 6 (0-5v)F1ain 7 (0-5v)F2ain 8(0-5V)F3din/vr 4F4din/vr5G1gpo 15(+12v)G2gpo 16 (+12v)G3ain 5 (0-5V)G4eNGINE GROUNDH1mOTOR 2+H2mOTOR 1-H3mOTOR 2-H4mOTOR 1+

Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.

All positions of the GEN1 connectors, including this unit's, are listed as a structured pin index in MaxxECU GEN1 connector pinout.

Software and further documents

MaxxECU RACE: product informationModel wiring and pinout referenceMTune, quick-start guides and revision-specific wiring downloadsMaxxECU family overview

Sources reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: MaxxECU RACE

MaxxECU RACE — Eight-cylinder sequential ECU with eight peak-and-hold injectors, electronic throttle, knock inputs and eight thermocouple inputs. MaxxECU product information.

MaxxECU RACE
MaxxECU RACE, manufacturer product image: MaxxECU. Used with permission.

Model identification and capabilities

The manufacturer lists eight ignition outputs, nine low-driving auxiliary outputs, two 12 V driving outputs and four motor outputs. Built-in features include a 400 kPa MAP sensor, wideband lambda controller and two knock inputs. Up to twelve cylinders can be controlled with wasted-spark ignition, depending on configuration. Manufacturer specification; MaxxECU model comparison.

Sequential cylinders, maximum8
Injector outputs8 peak-and-hold
Ignition outputs8
ConfigurationMTune; check the release appropriate to the ECU and hardware revision

Identification and installation

This is the original RACE, not GEN2 RACE. Use the model and hardware revision to select the wiring diagram; the manufacturer identifies RACE H2O as a separate water-protected version.

Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.

Connector and pinout

Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.

PositionManufacturer functionNotes
A1GPO 5
A2IGN 1
A3IGN 2
A4GPO 8/TACHO660ohm pullup
B1GPO 6
B2IGN 3
B3IGN 4
B4GPO 1
C1GPO 7
C2IGN 5
C3IGN 6
C4GPO 2
D1WBO2 Heater-
D2IGN 7
D3IGN 8
D4GPO 3
E1CAN H
E2CAN L
E3GND Shield
E4GPO 4
F1CLT
F2IAT
F3WBO2 VREF
F4WBO2 VS
G1+5V sensor supply(peak 0.5A, max 150mA)
G2TPS/AIN
G3WBO2 IP
G4WBO2 RCAL
H1Sensor GND
H2Trigger GND
H3TRIGGER
H4HOME
J1AIN 1 (Temperature)
J2AIN 2 (Temperature)
J3AIN 3 (0-5V)
J4AIN 4 (0-5V)
K1INJ 1
K2INJ 2
K3DIN/VR 1
K4DIN/VR 2
L1INJ 8
L2INJ 7
L3INJ 6
L4Engine GND
M1INJ 3
M2INJ 4
M3INJ 5
M4+12V ECU power supply

RACE connector 2

From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.

PositionManufacturer functionNotes
A1egt 5+
A2egt 6+
A3egt 7+
A4egt 8+
B1egt 5-
B2egt 6-
B3egt 7-
B4egt 8-
C1EGT 1 +
C2EGT 2+
C3EGT 3+
C4EGT 4+
D1EGT 1-
D2EGT 2-
D3EGT 3-
D4EGT 4-
E1KNOCK GND
E2Knock 1
E3knock 2
E4AIN 6 (0-5v)
F1ain 7 (0-5v)
F2ain 8(0-5V)
F3din/vr 4
F4din/vr5
G1gpo 15(+12v)
G2gpo 16 (+12v)
G3ain 5 (0-5V)
G4eNGINE GROUND
H1mOTOR 2+
H2mOTOR 1-
H3mOTOR 2-
H4mOTOR 1+

Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.

Software and further documents

Sources reviewed 17 November 2026.

Revision 4: MaxxECU RACE

MaxxECU RACE — Eight-cylinder sequential ECU with eight peak-and-hold injectors, electronic throttle, knock inputs and eight thermocouple inputs. MaxxECU product information.

MaxxECU RACE
MaxxECU RACE, manufacturer product image: MaxxECU. Used with permission.

Model identification and capabilities

The manufacturer lists eight ignition outputs, nine low-driving auxiliary outputs, two 12 V driving outputs and four motor outputs. Built-in features include a 400 kPa MAP sensor, wideband lambda controller and two knock inputs. Up to twelve cylinders can be controlled with wasted-spark ignition, depending on configuration. Manufacturer specification; MaxxECU model comparison.

Sequential cylinders, maximum8
Injector outputs8 peak-and-hold
Ignition outputs8
ConfigurationMTune; check the release appropriate to the ECU and hardware revision

Processor

The manufacturer product page lists an ARM Cortex-M3 main processor running at 120 MHz, with three further processors handling the trigger, injectors and knock detection (manufacturer specification). The specific microcontroller part number is not published.

Identification and installation

This is the original RACE, not GEN2 RACE. Use the model and hardware revision to select the wiring diagram; the manufacturer identifies RACE H2O as a separate water-protected version.

Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.

Connector and pinout

Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.

PositionManufacturer functionNotes
A1GPO 5
A2IGN 1
A3IGN 2
A4GPO 8/TACHO660ohm pullup
B1GPO 6
B2IGN 3
B3IGN 4
B4GPO 1
C1GPO 7
C2IGN 5
C3IGN 6
C4GPO 2
D1WBO2 Heater-
D2IGN 7
D3IGN 8
D4GPO 3
E1CAN H
E2CAN L
E3GND Shield
E4GPO 4
F1CLT
F2IAT
F3WBO2 VREF
F4WBO2 VS
G1+5V sensor supply(peak 0.5A, max 150mA)
G2TPS/AIN
G3WBO2 IP
G4WBO2 RCAL
H1Sensor GND
H2Trigger GND
H3TRIGGER
H4HOME
J1AIN 1 (Temperature)
J2AIN 2 (Temperature)
J3AIN 3 (0-5V)
J4AIN 4 (0-5V)
K1INJ 1
K2INJ 2
K3DIN/VR 1
K4DIN/VR 2
L1INJ 8
L2INJ 7
L3INJ 6
L4Engine GND
M1INJ 3
M2INJ 4
M3INJ 5
M4+12V ECU power supply

RACE connector 2

From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.

PositionManufacturer functionNotes
A1egt 5+
A2egt 6+
A3egt 7+
A4egt 8+
B1egt 5-
B2egt 6-
B3egt 7-
B4egt 8-
C1EGT 1 +
C2EGT 2+
C3EGT 3+
C4EGT 4+
D1EGT 1-
D2EGT 2-
D3EGT 3-
D4EGT 4-
E1KNOCK GND
E2Knock 1
E3knock 2
E4AIN 6 (0-5v)
F1ain 7 (0-5v)
F2ain 8(0-5V)
F3din/vr 4
F4din/vr5
G1gpo 15(+12v)
G2gpo 16 (+12v)
G3ain 5 (0-5V)
G4eNGINE GROUND
H1mOTOR 2+
H2mOTOR 1-
H3mOTOR 2-
H4mOTOR 1+

Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.

All positions of the GEN1 connectors, including this unit's, are listed as a structured pin index in MaxxECU GEN1 connector pinout.

Software and further documents

Sources reviewed 17 November 2026.