Removed text is struck through; added text is highlighted.
MaxxECU MINI — Compact entry ECU with four injector and four ignition outputs; up to four fully sequential cylinders or eight in wasted spark. MaxxECU product information.
MaxxECU MINI, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
A 400 kPa absolute MAP sensor is built in. The MINI has one VR/Hall trigger, two extra Hall/digital inputs and two extra 0–5 V analogue inputs in addition to its named temperature and throttle inputs. The manufacturer specifies four auxiliary outputs and 8 MB of internal logging, up to 1000 Hz. CAN and USB are available. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum4Injector outputs4 high-impedanceIgnition outputs4ConfigurationMTune; check the release appropriate to the ECU and hardware revision
Identification and installation
It does not include an internal wideband controller: use the documented external analogue or CAN solution. Injector outputs are intended for high-impedance injectors; observe the manufacturer’s instructions for low-impedance injectors and external current limiting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
MINI connector 1, REV10+; see the linked manufacturer drawing for the connector face and its cavity positions. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
PositionManufacturer functionNotesA1TRIGGERA2TRIGGER GNDA3Not assigned in sourceA4Not assigned in sourceB1DIN 1 (Hall onLY)B2DIN 2 (Hall only)B3SENSOR GNDB4SENSOR GNDC1CLTC2IATC3AIN 3 (0-5V)C4AIN 4 (0-5V)D1GPO 8/TACHO660ohm pullupD2TPSD3GND ShieldD4SENSOR GNDE1GPO 3E2+5V sensor supply(peak 0.5A, max 150mA)E3CAN LRead important note below if you encounter issues with CAN communications!E4CAN HRead important note below if you encounter issues with CAN communications!F1IGN 1F2IGN 2F3IGN 3F4IGN 4G1GPO 2G2GPO 1G3INJ 1G4ENGINE GNDH1INJ 2H2INJ 3H3INJ 4H4+12V (ECU power supply)
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
MaxxECU reports that approximately the first 100 MINI harnesses delivered in 2019 had CAN H and CAN L swapped in harness labelling; ECU positions remain E4 CAN H and E3 CAN L. Verify the actual loom against the manufacturer’s harness notice.
Software and further documents
MaxxECU MINI: product informationModel wiring and pinout referenceMTune, quick-start guides and revision-specific wiring downloadsMaxxECU family overview
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MaxxECU MINI
MaxxECU MINI — Compact entry ECU with four injector and four ignition outputs; up to four fully sequential cylinders or eight in wasted spark. MaxxECU product information.
MaxxECU MINI, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
A 400 kPa absolute MAP sensor is built in. The MINI has one VR/Hall trigger, two extra Hall/digital inputs and two extra 0–5 V analogue inputs in addition to its named temperature and throttle inputs. The manufacturer specifies four auxiliary outputs and 8 MB of internal logging, up to 1000 Hz. CAN and USB are available. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum
4
Injector outputs
4 high-impedance
Ignition outputs
4
Configuration
MTune; check the release appropriate to the ECU and hardware revision
Identification and installation
It does not include an internal wideband controller: use the documented external analogue or CAN solution. Injector outputs are intended for high-impedance injectors; observe the manufacturer’s instructions for low-impedance injectors and external current limiting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
MINI connector 1, REV10+; see the linked manufacturer drawing for the connector face and its cavity positions. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
Position
Manufacturer function
Notes
A1
TRIGGER
A2
TRIGGER GND
A3
Not assigned in source
A4
Not assigned in source
B1
DIN 1 (Hall onLY)
B2
DIN 2 (Hall only)
B3
SENSOR GND
B4
SENSOR GND
C1
CLT
C2
IAT
C3
AIN 3 (0-5V)
C4
AIN 4 (0-5V)
D1
GPO 8/TACHO
660ohm pullup
D2
TPS
D3
GND Shield
D4
SENSOR GND
E1
GPO 3
E2
+5V sensor supply
(peak 0.5A, max 150mA)
E3
CAN L
Read important note below if you encounter issues with CAN communications!
E4
CAN H
Read important note below if you encounter issues with CAN communications!
F1
IGN 1
F2
IGN 2
F3
IGN 3
F4
IGN 4
G1
GPO 2
G2
GPO 1
G3
INJ 1
G4
ENGINE GND
H1
INJ 2
H2
INJ 3
H3
INJ 4
H4
+12V (ECU power supply)
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
MaxxECU reports that approximately the first 100 MINI harnesses delivered in 2019 had CAN H and CAN L swapped in harness labelling; ECU positions remain E4 CAN H and E3 CAN L. Verify the actual loom against the manufacturer’s harness notice.
MaxxECU MINI — Compact entry ECU with four injector and four ignition outputs; up to four fully sequential cylinders or eight in wasted spark. MaxxECU product information.
MaxxECU MINI, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
A 400 kPa absolute MAP sensor is built in. The MINI has one VR/Hall trigger, two extra Hall/digital inputs and two extra 0–5 V analogue inputs in addition to its named temperature and throttle inputs. The manufacturer specifies four auxiliary outputs and 8 MB of internal logging, up to 1000 Hz. CAN and USB are available. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum
4
Injector outputs
4 high-impedance
Ignition outputs
4
Configuration
MTune; check the release appropriate to the ECU and hardware revision
Identification and installation
It does not include an internal wideband controller: use the documented external analogue or CAN solution. Injector outputs are intended for high-impedance injectors; observe the manufacturer’s instructions for low-impedance injectors and external current limiting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
MINI connector 1, REV10+; see the linked manufacturer drawing for the connector face and its cavity positions. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
Position
Manufacturer function
Notes
A1
TRIGGER
A2
TRIGGER GND
A3
Not assigned in source
A4
Not assigned in source
B1
DIN 1 (Hall onLY)
B2
DIN 2 (Hall only)
B3
SENSOR GND
B4
SENSOR GND
C1
CLT
C2
IAT
C3
AIN 3 (0-5V)
C4
AIN 4 (0-5V)
D1
GPO 8/TACHO
660ohm pullup
D2
TPS
D3
GND Shield
D4
SENSOR GND
E1
GPO 3
E2
+5V sensor supply
(peak 0.5A, max 150mA)
E3
CAN L
Read important note below if you encounter issues with CAN communications!
E4
CAN H
Read important note below if you encounter issues with CAN communications!
F1
IGN 1
F2
IGN 2
F3
IGN 3
F4
IGN 4
G1
GPO 2
G2
GPO 1
G3
INJ 1
G4
ENGINE GND
H1
INJ 2
H2
INJ 3
H3
INJ 4
H4
+12V (ECU power supply)
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
MaxxECU reports that approximately the first 100 MINI harnesses delivered in 2019 had CAN H and CAN L swapped in harness labelling; ECU positions remain E4 CAN H and E3 CAN L. Verify the actual loom against the manufacturer’s harness notice.