Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

DTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.

The DTAFast S80 Pro is an S-series programmable engine-management unit. Eight injector and eight coil drivers with two cam inputs in the historical DTA feature matrix. The S-series manual describes traction control on S80 Pro and above. DTAFast historical S-series feature matrix.

Hardware and operation

Refer to the manufacturer S80 Pro connector diagrams, sensor options and notes; outputs can be shared by configurable functions. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.

Wiring and pinout

DTAFast S80 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.

Software and additional references

The DTAFast S-series Pro manual describes DTASwin calibration software, data logging and model-specific settings. DTAFast S60 Pro product sheet provides an example of output and engine configuration limits. See the DTAFast model family for other ECUs.

S80 Pro pinout — manufacturer diagramPower and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S80 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.Power connectionsPinDocumented function1Coil 32Aux 9 / tacho3Aux 7 / fuel pump relay4Aux 2 / fan relay5Aux 1 / cam control6Aux 8 / shift light / electric dump valve7Turbo pressure valve8Idle valve9Injector 110Coil 111Coil 512Coil 713, 14Power grounds15Injector 616Injector 517Injector 218Coil 219Coil 821Cam 223Injector 824Injector 725Injector 426Coil 427Coil 629Aux 5 (12 V output)30Aux 631Fused 12 V supply32Aux 4 / ALS / VTEC33Aux 3 / VTEC / Bosch 3-pin idle valve fast side34Injector 3Sensor connectionsPinDocumented function1Analogue 2 / log switch / TPS 22Undriven wheel speed, Hall effect3Analogue 3 / gear potentiometer4Launch button5Oil pressure6Fuel pressure7Air temperature95 V output10Analogue 1 / traction cut percentage / launch RPM12Crank magnetic13Crank Hall effect14Shift cut / E85 / air-con / shaft speed15ALS / map 2 / lambda switch16Manifold / barometric pressure17Oil temperature19Left or only lambda signal21, 33Sensor ground22Cam magnetic23Cam Hall effect25Water temperature26CAN high28CAN low34Throttle position8Traction on/off switch11Traction wet/dry switch18Right lambda or launch RPM20Right undriven wheel speed245 V output27Aux switch / pit lane speed29Cam 2 Hall effect30Cam 2 magnetic31Left driven wheel speed32Right driven wheel speedThe manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: DTAFast S80 Pro

The DTAFast S80 Pro is an S-series programmable engine-management unit. Eight injector and eight coil drivers with two cam inputs in the historical DTA feature matrix. The S-series manual describes traction control on S80 Pro and above. DTAFast historical S-series feature matrix.

Hardware and operation

Refer to the manufacturer S80 Pro connector diagrams, sensor options and notes; outputs can be shared by configurable functions. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.

Wiring and pinout

DTAFast S80 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.

Software and additional references

The DTAFast S-series Pro manual describes DTASwin calibration software, data logging and model-specific settings. DTAFast S60 Pro product sheet provides an example of output and engine configuration limits. See the DTAFast model family for other ECUs.

Revision 3: DTAFast S80 Pro
DTAFast S-series ECU range
DTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.

The DTAFast S80 Pro is an S-series programmable engine-management unit. Eight injector and eight coil drivers with two cam inputs in the historical DTA feature matrix. The S-series manual describes traction control on S80 Pro and above. DTAFast historical S-series feature matrix.

Hardware and operation

Refer to the manufacturer S80 Pro connector diagrams, sensor options and notes; outputs can be shared by configurable functions. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.

Wiring and pinout

DTAFast S80 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.

Software and additional references

The DTAFast S-series Pro manual describes DTASwin calibration software, data logging and model-specific settings. DTAFast S60 Pro product sheet provides an example of output and engine configuration limits. See the DTAFast model family for other ECUs.

S80 Pro pinout — manufacturer diagram

Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S80 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.

Power connections

PinDocumented function
1Coil 3
2Aux 9 / tacho
3Aux 7 / fuel pump relay
4Aux 2 / fan relay
5Aux 1 / cam control
6Aux 8 / shift light / electric dump valve
7Turbo pressure valve
8Idle valve
9Injector 1
10Coil 1
11Coil 5
12Coil 7
13, 14Power grounds
15Injector 6
16Injector 5
17Injector 2
18Coil 2
19Coil 8
21Cam 2
23Injector 8
24Injector 7
25Injector 4
26Coil 4
27Coil 6
29Aux 5 (12 V output)
30Aux 6
31Fused 12 V supply
32Aux 4 / ALS / VTEC
33Aux 3 / VTEC / Bosch 3-pin idle valve fast side
34Injector 3

Sensor connections

PinDocumented function
1Analogue 2 / log switch / TPS 2
2Undriven wheel speed, Hall effect
3Analogue 3 / gear potentiometer
4Launch button
5Oil pressure
6Fuel pressure
7Air temperature
95 V output
10Analogue 1 / traction cut percentage / launch RPM
12Crank magnetic
13Crank Hall effect
14Shift cut / E85 / air-con / shaft speed
15ALS / map 2 / lambda switch
16Manifold / barometric pressure
17Oil temperature
19Left or only lambda signal
21, 33Sensor ground
22Cam magnetic
23Cam Hall effect
25Water temperature
26CAN high
28CAN low
34Throttle position
8Traction on/off switch
11Traction wet/dry switch
18Right lambda or launch RPM
20Right undriven wheel speed
245 V output
27Aux switch / pit lane speed
29Cam 2 Hall effect
30Cam 2 magnetic
31Left driven wheel speed
32Right driven wheel speed

The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.