Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

DTAFast E48 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 30 March 2001 manufacturer schematic is labelled E48EXP and E48EXP ignition only. It illustrates two coil outputs, injector connections, configurable auxiliary and sensor functions; establish the exact build before assuming fuel drivers are present.

Identification

Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.

Model-specific pinout and wiring

The manufacturer E48 drawing supplies connector views, functions, sensor/actuator examples and grounding. The linked document explicitly covers both E48EXP and its ignition-only version; confirm which electronics are fitted before connecting injectors. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.

Related documentation

DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.

E48EXP 25-way wiring scheduleThese assignments are transcribed from the DTAFast E48EXP / E48EXP ignition-only schematic dated 30 March 2001. The document shows the common drawing for both models; do not assume injector output hardware is fitted to an ignition-only unit. Match the precise unit and connector view to the original and check electrical limits. Auxiliary outputs are specified as 500 mA maximum; the drawing requires both power-ground positions connected.PinFunction shown1Lambda signal2Lambda ground3Gear-shift cut switch4Launch control switch55 V sensor supply65 V sensor supply7Sensor ground8Auxiliary 2 output9Tachometer output10Fuel-pump relay output11Gear-change light output12Battery negative / power ground13Battery negative / power ground14Throttle-position wiper15Water temperature signal16Air temperature signal17Pressure sensor signal18Crank sensor signal (VR)19Wheel sensor output (Hall)20Sensor ground / crank sensor return21Injector 2 or idle valve (fuel-equipped build)22Injector 1 (fuel-equipped build)23Coil 224Coil 125Switched 12 V ECU supplyIn the schematic, sensor grounds and 5 V outputs are common within their groups except for the separate lambda ground. The manufacturer also provides differing crank-sensor wire positions for Ford, Bosch/Siemens and Marelli sensors; consult the original diagram and do not assume pin order across sensor makes.Programming lead DB9 connectorRace Technology's E48 and P8 PRO integration documentation describes these RS232 signals at the nine-way end of DTA's DB15-to-DB9 serial lead. These are pins on the cable's DB9 connector, not positions on the ECU's DB15 connector.DB9 pinDocumented signal2TX3RX5GroundThe source does not document the other DB9 positions; do not infer their connections.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: DTAFast E48

DTAFast E48 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 30 March 2001 manufacturer schematic is labelled E48EXP and E48EXP ignition only. It illustrates two coil outputs, injector connections, configurable auxiliary and sensor functions; establish the exact build before assuming fuel drivers are present.

Identification

Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.

Model-specific pinout and wiring

The manufacturer E48 drawing supplies connector views, functions, sensor/actuator examples and grounding. The linked document explicitly covers both E48EXP and its ignition-only version; confirm which electronics are fitted before connecting injectors. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.

Related documentation

DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.

Revision 3: DTAFast E48

DTAFast E48 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 30 March 2001 manufacturer schematic is labelled E48EXP and E48EXP ignition only. It illustrates two coil outputs, injector connections, configurable auxiliary and sensor functions; establish the exact build before assuming fuel drivers are present.

Identification

Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.

Model-specific pinout and wiring

The manufacturer E48 drawing supplies connector views, functions, sensor/actuator examples and grounding. The linked document explicitly covers both E48EXP and its ignition-only version; confirm which electronics are fitted before connecting injectors. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.

Related documentation

DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.

E48EXP 25-way wiring schedule

These assignments are transcribed from the DTAFast E48EXP / E48EXP ignition-only schematic dated 30 March 2001. The document shows the common drawing for both models; do not assume injector output hardware is fitted to an ignition-only unit. Match the precise unit and connector view to the original and check electrical limits. Auxiliary outputs are specified as 500 mA maximum; the drawing requires both power-ground positions connected.

PinFunction shown
1Lambda signal
2Lambda ground
3Gear-shift cut switch
4Launch control switch
55 V sensor supply
65 V sensor supply
7Sensor ground
8Auxiliary 2 output
9Tachometer output
10Fuel-pump relay output
11Gear-change light output
12Battery negative / power ground
13Battery negative / power ground
14Throttle-position wiper
15Water temperature signal
16Air temperature signal
17Pressure sensor signal
18Crank sensor signal (VR)
19Wheel sensor output (Hall)
20Sensor ground / crank sensor return
21Injector 2 or idle valve (fuel-equipped build)
22Injector 1 (fuel-equipped build)
23Coil 2
24Coil 1
25Switched 12 V ECU supply

In the schematic, sensor grounds and 5 V outputs are common within their groups except for the separate lambda ground. The manufacturer also provides differing crank-sensor wire positions for Ford, Bosch/Siemens and Marelli sensors; consult the original diagram and do not assume pin order across sensor makes.

Programming lead DB9 connector

Race Technology's E48 and P8 PRO integration documentation describes these RS232 signals at the nine-way end of DTA's DB15-to-DB9 serial lead. These are pins on the cable's DB9 connector, not positions on the ECU's DB15 connector.

DB9 pinDocumented signal
2TX
3RX
5Ground

The source does not document the other DB9 positions; do not infer their connections.