Removed text is struck through; added text is highlighted.
MaxxECU PRO — High-channel-count GEN1 ECU for up to twelve sequential cylinders, with sixteen injector drivers and twelve ignition outputs. MaxxECU product information.
MaxxECU PRO, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
The manufacturer lists 16 peak-and-hold injector outputs, dual wideband LSU 4.2/4.9 support, 12 type K/N EGT inputs, 16 extra 0–5 V inputs, six extra temperature inputs and dual electronic-throttle capability. Its built-in MAP sensor is rated 400 kPa absolute; Bluetooth, USB and CAN are provided. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum12Injector outputs16 peak-and-holdIgnition outputs12ConfigurationMTune; check the release appropriate to the ECU and hardware revision
Identification and installation
Connector 4 has revision-dependent knock and sensor-ground assignments: MaxxECU documents knock inputs on REV10+ and different ground assignments on earlier units. Verify the serial and exact revision before connecting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Selected connector 1 positions shared in the manufacturer’s GEN1 table; consult the PRO column and all connector diagrams for full details. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
PRO connector 2From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.PositionManufacturer functionNotesA1EGT 1+A2EGT 2+A3EGT 3+A4EGT 4+B1EGT 1-B2EGT 2-B3EGT 3-B4EGT 4-C1EGT 5+C2EGT 6+C3EGT 7+C4EGT 8+D1EGT 5-D2EGT 6-D3EGT 7-D4EGT 8-E1EGT 9+E2EGT 10+E3EGT 11+E4EGT 12+F1EGT 9-F2EGT 10-F3EGT 11-F4EGT 12-G1Not assigned in sourceG2Not assigned in sourceG3Not assigned in sourceG4Not assigned in sourceH1Engine ground 3H2Engine ground 3H3engine ground 3H4Not assigned in sourcePRO connector 3From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.PositionManufacturer functionNotesA1DIN/VR 4A2DIN/VR 5A3DIN 6 (SWITCH)A4DIN 7 (SWITCH)B1WBO2 2 RCALB2WBO2 2 IPB3WBO2 2 VSB4WBO2 2 COMC1WBO2 2 ShieldC2+5V SENSOR SUPPLY 2(peak 0.5A, max 150mA)C3ANALOG in 5 (0-5V)C4GPO 19 (12V)D1ANALOG IN 6 (0-5V)D2ANALOG IN 7 (0-5V)D3ANALOG IN 8 (0-5V)D4GPO 20 (12V)E1GPO 10/WBO2 2 HTR PIN 4E2ANALOG IN 9 (0-5V)E3ANALOG IN 10 (0-5V)E4GPO 21 (12V)F1INJECTOR OUT 15F2ANALOG IN 11 (0-5V)F3ANALOG IN 12 (0-5V)F4GPO 22 (12V)G1INJECTOR OUT 14G2IGNITION OUT 11G3IGNITION OUT 9G4GPO 15 (12V)H1INJECTOR OUT 13H2IGNITION OUT 12H3IGNITION OUT 10H4GPO 16 (12V)J1INJECTOR OUT 16J2SENSOR GNDJ3SENSOR GNDJ4GPO 17 (12V)K1INJECTOR OUT 10K2INJECTOR OUT 9K3KEY IN 12VK4GPO 18 (12V)L1INJECTOR OUT 11L2GPO 12/MOTOR 1 +L3GPO 11/MOTOR 1 -L4ENGINE GROUND 2M1INJECTOR OUT 12M2GPO 13/Motor 2 +M3GPO 14/Motor 2 -M412V ECU 2PRO connector 4From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.PositionManufacturer functionNotesA1CAN 2 HA2CAN 2 LA30-5v out 1A40-5v out 2B1AIN 18 (0-5v)B2AIN 17 (0-5v)B3AIN 16 (0-5v)B4AIN 15 (0-5v)C1AIN 14 (0-5v)C2AIN 13 (0-5v)C3AIN 19 (temp)C4AIN 20 (temp)D1AIN 21 (temp)D2AIN 22 (temp)D3DIN 8 (switch)D4din 9 (switch)E1DIn 10 (switch)E2Din 11 (switch)E3+5v sensor supply 3(peak 0.5A, max 150mA)E45-10v sensor supplyF1GPO 23-30 flybackF2knock 1Only available on REV10+ unitsF3knock 2REV10+ units = KNOCK 2, earlier rev = Sensor GND 3F4Sensor GND3 / knock groundREV10+ units = KNOCK GND, earlier rev = Sensor GND 3G1GPO 23G2GPO 24G3GPO 25G4GPO 26H1GPO 27H2GPO 28H3GPO 29H4GPO 30
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
Software and further documents
MaxxECU PRO: product informationModel wiring and pinout referenceMTune, quick-start guides and revision-specific wiring downloadsMaxxECU family overview
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MaxxECU PRO
MaxxECU PRO — High-channel-count GEN1 ECU for up to twelve sequential cylinders, with sixteen injector drivers and twelve ignition outputs. MaxxECU product information.
MaxxECU PRO, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
The manufacturer lists 16 peak-and-hold injector outputs, dual wideband LSU 4.2/4.9 support, 12 type K/N EGT inputs, 16 extra 0–5 V inputs, six extra temperature inputs and dual electronic-throttle capability. Its built-in MAP sensor is rated 400 kPa absolute; Bluetooth, USB and CAN are provided. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum
12
Injector outputs
16 peak-and-hold
Ignition outputs
12
Configuration
MTune; check the release appropriate to the ECU and hardware revision
Identification and installation
Connector 4 has revision-dependent knock and sensor-ground assignments: MaxxECU documents knock inputs on REV10+ and different ground assignments on earlier units. Verify the serial and exact revision before connecting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Selected connector 1 positions shared in the manufacturer’s GEN1 table; consult the PRO column and all connector diagrams for full details. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
Position
Manufacturer function
Notes
A1
GPO 5
A2
IGN 1
A3
IGN 2
A4
GPO 8/TACHO
660ohm pullup
B1
GPO 6
B2
IGN 3
B3
IGN 4
B4
GPO 1
C1
GPO 7
C2
IGN 5
C3
IGN 6
C4
GPO 2
D1
WBO2 Heater-
D2
IGN 7
D3
IGN 8
D4
GPO 3
E1
CAN H
E2
CAN L
E3
GND Shield
E4
GPO 4
F1
CLT
F2
IAT
F3
WBO2 VREF
F4
WBO2 VS
G1
+5V sensor supply
(peak 0.5A, max 150mA)
G2
TPS/AIN
G3
WBO2 IP
G4
WBO2 RCAL
H1
Sensor GND
H2
Trigger GND
H3
TRIGGER
H4
HOME
J1
AIN 1 (Temperature)
J2
AIN 2 (Temperature)
J3
AIN 3 (0-5V)
J4
AIN 4 (0-5V)
K1
INJ 1
K2
INJ 2
K3
DIN/VR 1
K4
DIN/VR 2
L1
INJ 8
L2
INJ 7
L3
INJ 6
L4
Engine GND
M1
INJ 3
M2
INJ 4
M3
INJ 5
M4
+12V ECU power supply
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
MaxxECU PRO — High-channel-count GEN1 ECU for up to twelve sequential cylinders, with sixteen injector drivers and twelve ignition outputs. MaxxECU product information.
MaxxECU PRO, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
The manufacturer lists 16 peak-and-hold injector outputs, dual wideband LSU 4.2/4.9 support, 12 type K/N EGT inputs, 16 extra 0–5 V inputs, six extra temperature inputs and dual electronic-throttle capability. Its built-in MAP sensor is rated 400 kPa absolute; Bluetooth, USB and CAN are provided. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum
12
Injector outputs
16 peak-and-hold
Ignition outputs
12
Configuration
MTune; check the release appropriate to the ECU and hardware revision
Identification and installation
Connector 4 has revision-dependent knock and sensor-ground assignments: MaxxECU documents knock inputs on REV10+ and different ground assignments on earlier units. Verify the serial and exact revision before connecting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Selected connector 1 positions shared in the manufacturer’s GEN1 table; consult the PRO column and all connector diagrams for full details. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.