Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Emerald standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

Emerald M3DK is an Emerald engine-management designation. Produced March 2001 to February 2007, M3DK was Emerald's first 32-bit ECU, intended primarily for four-cylinder normally aspirated or boosted engines. It has four injector drivers and two internal ignition drivers, RS232 communication, idle control and Rover MEMS immobiliser provisions. Emerald manufacturer information.

Identification and configuration

Identify the exact hardware and serial number. Emerald notes that some units have bespoke software for non-standard installations, and that many M3DK units were upgraded to K3 specification. An old case label alone cannot establish the internal specification. Emerald earlier ECU information; software and manuals.

Emerald provides a K3/K6 software family separately from M3DK software. Its K6 generic and preconfigured packages are ordering/configuration choices; a base map is a starting point requiring matching and calibration for the actual engine.

Pinout, harness and software

The M3DK manual v5 includes a 36-way connector table and distinguishes individual sensor and output assignments. Some M3DK ECUs were upgraded to K3 specification; establish the actual internals before wiring. Manufacturer manual or documentation. Use terminal markings, exact connector view and the source's wiring and driver notes. A model-specific adapter for an original vehicle harness is distinct from the generic connector assignment.

See Emerald adapter catalogue and Emerald standalone ECU overview.

M3DK 36-way pinout — manual v5

The following is specific to the M3DK documented in Emerald's M3DK manual v5, page 53; consult the diagram for connector orientation. Upgraded or bespoke ECUs may differ. The source notes that driver outputs other than tacho are switched earths.

PinFunction1Injector driver 42IACV channel 23IACV channel 14Main relay control5Ignition driver 26Cooling fan relay7Oxygen signal8Throttle position signal95 V throttle sensor supply, 100 mA max10Aux output 111Ignition sense +12 V12Tacho13Immobiliser input148 V output15Cam phase or custom input16Air temperature17Aux output 218Oxygen signal earth19Shift light20Fuel pump relay21Purge valve / auxiliary output 322IACV channel 323Injector driver 224Injector driver 125Ignition driver 126Injector driver 327IACV channel 428+12 V ignition supply29ECU earth30Sensor earth31Main trigger signal32Main trigger sensor earth33Coolant temperature34Aux analogue input 135Aux analogue input 236Oxygen heater relay driver

Structured connector pinoutThe 36-way table above is also given as a structured pin index with a redrawn rear-view connector face in Emerald M3DK connector pinout. The M3DK manual v5 does not name the ECU's microcontroller.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Emerald M3DK

Emerald M3DK is an Emerald engine-management designation. Produced March 2001 to February 2007, M3DK was Emerald's first 32-bit ECU, intended primarily for four-cylinder normally aspirated or boosted engines. It has four injector drivers and two internal ignition drivers, RS232 communication, idle control and Rover MEMS immobiliser provisions. Emerald manufacturer information.

Identification and configuration

Identify the exact hardware and serial number. Emerald notes that some units have bespoke software for non-standard installations, and that many M3DK units were upgraded to K3 specification. An old case label alone cannot establish the internal specification. Emerald earlier ECU information; software and manuals.

Emerald provides a K3/K6 software family separately from M3DK software. Its K6 generic and preconfigured packages are ordering/configuration choices; a base map is a starting point requiring matching and calibration for the actual engine.

Pinout, harness and software

The M3DK manual v5 includes a 36-way connector table and distinguishes individual sensor and output assignments. Some M3DK ECUs were upgraded to K3 specification; establish the actual internals before wiring. Manufacturer manual or documentation. Use terminal markings, exact connector view and the source's wiring and driver notes. A model-specific adapter for an original vehicle harness is distinct from the generic connector assignment.

See Emerald adapter catalogue and Emerald standalone ECU overview.

M3DK 36-way pinout — manual v5

The following is specific to the M3DK documented in Emerald's M3DK manual v5, page 53; consult the diagram for connector orientation. Upgraded or bespoke ECUs may differ. The source notes that driver outputs other than tacho are switched earths.

PinFunction
1Injector driver 4
2IACV channel 2
3IACV channel 1
4Main relay control
5Ignition driver 2
6Cooling fan relay
7Oxygen signal
8Throttle position signal
95 V throttle sensor supply, 100 mA max
10Aux output 1
11Ignition sense +12 V
12Tacho
13Immobiliser input
148 V output
15Cam phase or custom input
16Air temperature
17Aux output 2
18Oxygen signal earth
19Shift light
20Fuel pump relay
21Purge valve / auxiliary output 3
22IACV channel 3
23Injector driver 2
24Injector driver 1
25Ignition driver 1
26Injector driver 3
27IACV channel 4
28+12 V ignition supply
29ECU earth
30Sensor earth
31Main trigger signal
32Main trigger sensor earth
33Coolant temperature
34Aux analogue input 1
35Aux analogue input 2
36Oxygen heater relay driver
Revision 3: Emerald M3DK

Emerald M3DK is an Emerald engine-management designation. Produced March 2001 to February 2007, M3DK was Emerald's first 32-bit ECU, intended primarily for four-cylinder normally aspirated or boosted engines. It has four injector drivers and two internal ignition drivers, RS232 communication, idle control and Rover MEMS immobiliser provisions. Emerald manufacturer information.

Identification and configuration

Identify the exact hardware and serial number. Emerald notes that some units have bespoke software for non-standard installations, and that many M3DK units were upgraded to K3 specification. An old case label alone cannot establish the internal specification. Emerald earlier ECU information; software and manuals.

Emerald provides a K3/K6 software family separately from M3DK software. Its K6 generic and preconfigured packages are ordering/configuration choices; a base map is a starting point requiring matching and calibration for the actual engine.

Pinout, harness and software

The M3DK manual v5 includes a 36-way connector table and distinguishes individual sensor and output assignments. Some M3DK ECUs were upgraded to K3 specification; establish the actual internals before wiring. Manufacturer manual or documentation. Use terminal markings, exact connector view and the source's wiring and driver notes. A model-specific adapter for an original vehicle harness is distinct from the generic connector assignment.

See Emerald adapter catalogue and Emerald standalone ECU overview.

M3DK 36-way pinout — manual v5

The following is specific to the M3DK documented in Emerald's M3DK manual v5, page 53; consult the diagram for connector orientation. Upgraded or bespoke ECUs may differ. The source notes that driver outputs other than tacho are switched earths.

PinFunction
1Injector driver 4
2IACV channel 2
3IACV channel 1
4Main relay control
5Ignition driver 2
6Cooling fan relay
7Oxygen signal
8Throttle position signal
95 V throttle sensor supply, 100 mA max
10Aux output 1
11Ignition sense +12 V
12Tacho
13Immobiliser input
148 V output
15Cam phase or custom input
16Air temperature
17Aux output 2
18Oxygen signal earth
19Shift light
20Fuel pump relay
21Purge valve / auxiliary output 3
22IACV channel 3
23Injector driver 2
24Injector driver 1
25Ignition driver 1
26Injector driver 3
27IACV channel 4
28+12 V ignition supply
29ECU earth
30Sensor earth
31Main trigger signal
32Main trigger sensor earth
33Coolant temperature
34Aux analogue input 1
35Aux analogue input 2
36Oxygen heater relay driver

Structured connector pinout

The 36-way table above is also given as a structured pin index with a redrawn rear-view connector face in Emerald M3DK connector pinout. The M3DK manual v5 does not name the ECU's microcontroller.