Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Emerald standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 3
Removed text is struck through; added text is highlighted.
Emerald M3DK is an Emerald engine-management designation. Produced March 2001 to February 2007, M3DK was Emerald's first 32-bit ECU, intended primarily for four-cylinder normally aspirated or boosted engines. It has four injector drivers and two internal ignition drivers, RS232 communication, idle control and Rover MEMS immobiliser provisions. Emerald manufacturer information.
Identification and configuration
Identify the exact hardware and serial number. Emerald notes that some units have bespoke software for non-standard installations, and that many M3DK units were upgraded to K3 specification. An old case label alone cannot establish the internal specification. Emerald earlier ECU information; software and manuals.
Emerald provides a K3/K6 software family separately from M3DK software. Its K6 generic and preconfigured packages are ordering/configuration choices; a base map is a starting point requiring matching and calibration for the actual engine.
Pinout, harness and software
The M3DK manual v5 includes a 36-way connector table and distinguishes individual sensor and output assignments. Some M3DK ECUs were upgraded to K3 specification; establish the actual internals before wiring. Manufacturer manual or documentation. Use terminal markings, exact connector view and the source's wiring and driver notes. A model-specific adapter for an original vehicle harness is distinct from the generic connector assignment.
See Emerald adapter catalogue and Emerald standalone ECU overview.
M3DK 36-way pinout — manual v5The following is specific to the M3DK documented in Emerald's M3DK manual v5, page 53; consult the diagram for connector orientation. Upgraded or bespoke ECUs may differ. The source notes that driver outputs other than tacho are switched earths.PinFunction1Injector driver 42IACV channel 23IACV channel 14Main relay control5Ignition driver 26Cooling fan relay7Oxygen signal8Throttle position signal95 V throttle sensor supply, 100 mA max10Aux output 111Ignition sense +12 V12Tacho13Immobiliser input148 V output15Cam phase or custom input16Air temperature17Aux output 218Oxygen signal earth19Shift light20Fuel pump relay21Purge valve / auxiliary output 322IACV channel 323Injector driver 224Injector driver 125Ignition driver 126Injector driver 327IACV channel 428+12 V ignition supply29ECU earth30Sensor earth31Main trigger signal32Main trigger sensor earth33Coolant temperature34Aux analogue input 135Aux analogue input 236Oxygen heater relay driverStructured connector pinoutThe 36-way table above is also given as a structured pin index with a redrawn rear-view connector face in Emerald M3DK connector pinout. The M3DK manual v5 does not name the ECU's microcontroller.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Emerald M3DK
Emerald M3DK is an Emerald engine-management designation. Produced March 2001 to February 2007, M3DK was Emerald's first 32-bit ECU, intended primarily for four-cylinder normally aspirated or boosted engines. It has four injector drivers and two internal ignition drivers, RS232 communication, idle control and Rover MEMS immobiliser provisions. Emerald manufacturer information.
Identification and configuration
Identify the exact hardware and serial number. Emerald notes that some units have bespoke software for non-standard installations, and that many M3DK units were upgraded to K3 specification. An old case label alone cannot establish the internal specification. Emerald earlier ECU information; software and manuals.
Emerald provides a K3/K6 software family separately from M3DK software. Its K6 generic and preconfigured packages are ordering/configuration choices; a base map is a starting point requiring matching and calibration for the actual engine.
Pinout, harness and software
The M3DK manual v5 includes a 36-way connector table and distinguishes individual sensor and output assignments. Some M3DK ECUs were upgraded to K3 specification; establish the actual internals before wiring. Manufacturer manual or documentation. Use terminal markings, exact connector view and the source's wiring and driver notes. A model-specific adapter for an original vehicle harness is distinct from the generic connector assignment.
See Emerald adapter catalogue and Emerald standalone ECU overview.
Revision 3: Emerald M3DK
Emerald M3DK is an Emerald engine-management designation. Produced March 2001 to February 2007, M3DK was Emerald's first 32-bit ECU, intended primarily for four-cylinder normally aspirated or boosted engines. It has four injector drivers and two internal ignition drivers, RS232 communication, idle control and Rover MEMS immobiliser provisions. Emerald manufacturer information.
Identification and configuration
Identify the exact hardware and serial number. Emerald notes that some units have bespoke software for non-standard installations, and that many M3DK units were upgraded to K3 specification. An old case label alone cannot establish the internal specification. Emerald earlier ECU information; software and manuals.
Emerald provides a K3/K6 software family separately from M3DK software. Its K6 generic and preconfigured packages are ordering/configuration choices; a base map is a starting point requiring matching and calibration for the actual engine.
Pinout, harness and software
The M3DK manual v5 includes a 36-way connector table and distinguishes individual sensor and output assignments. Some M3DK ECUs were upgraded to K3 specification; establish the actual internals before wiring. Manufacturer manual or documentation. Use terminal markings, exact connector view and the source's wiring and driver notes. A model-specific adapter for an original vehicle harness is distinct from the generic connector assignment.
See Emerald adapter catalogue and Emerald standalone ECU overview.
M3DK 36-way pinout — manual v5
The following is specific to the M3DK documented in Emerald's M3DK manual v5, page 53; consult the diagram for connector orientation. Upgraded or bespoke ECUs may differ. The source notes that driver outputs other than tacho are switched earths.
| Pin | Function |
|---|
| 1 | Injector driver 4 |
| 2 | IACV channel 2 |
| 3 | IACV channel 1 |
| 4 | Main relay control |
| 5 | Ignition driver 2 |
| 6 | Cooling fan relay |
| 7 | Oxygen signal |
| 8 | Throttle position signal |
| 9 | 5 V throttle sensor supply, 100 mA max |
| 10 | Aux output 1 |
| 11 | Ignition sense +12 V |
| 12 | Tacho |
| 13 | Immobiliser input |
| 14 | 8 V output |
| 15 | Cam phase or custom input |
| 16 | Air temperature |
| 17 | Aux output 2 |
| 18 | Oxygen signal earth |
| 19 | Shift light |
| 20 | Fuel pump relay |
| 21 | Purge valve / auxiliary output 3 |
| 22 | IACV channel 3 |
| 23 | Injector driver 2 |
| 24 | Injector driver 1 |
| 25 | Ignition driver 1 |
| 26 | Injector driver 3 |
| 27 | IACV channel 4 |
| 28 | +12 V ignition supply |
| 29 | ECU earth |
| 30 | Sensor earth |
| 31 | Main trigger signal |
| 32 | Main trigger sensor earth |
| 33 | Coolant temperature |
| 34 | Aux analogue input 1 |
| 35 | Aux analogue input 2 |
| 36 | Oxygen heater relay driver |
Structured connector pinout
The 36-way table above is also given as a structured pin index with a redrawn rear-view connector face in Emerald M3DK connector pinout. The M3DK manual v5 does not name the ECU's microcontroller.