Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Omex standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 3
Removed text is struck through; added text is highlighted.
The historical OMEM550 controls injection and ignition and uses MAP2000. Manual v3.02 describes throttle-position or manifold-pressure load input, air and coolant temperature sensors, narrowband oxygen feedback, a configurable auxiliary output and fuel and ignition maps. The manual documents crank trigger and distributor-trigger options; identify the sensor and programmed timing configuration. Model-specific Omex manual · Omex engine-management range.
Connector and pinout
The OMEM550 hardware manual v3.02 gives its model-specific ECU pinout in section 13.3 and wiring diagrams in section 13.4. Do not assume that a 500 or 600 loom is interchangeable. Open the exact-model installation or hardware manual.
Software and setup
The historical manual specifies MAP2000; software and communication requirements depend on the hardware and firmware. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.
Compare models and historical identities in the Omex family guide.
Manufacturer loom functions and coloursThese functions and loom colours are listed in section 13.3 of the Omex OMEM550 hardware manual v3.02. The accessible text transcription does not preserve the table alignment well enough to verify the individual cavity numbers, so this table identifies wires by colour only. Obtain the original illustrated table from Omex to confirm connector numbering and view.Omex loom colourDocumented functionYellowIgnition driver 2 outputScreened redTiming / crank-position pickup inputBlueAuxiliary outputOrangeThrottle position sensor wiper inputPink+5 V sensor power outputBrownInjector driver 1 outputGreen / whiteAir temperature sensor inputVioletIgnition driver 1 outputWhiteInjector driver 2 outputOrange / whiteOxygen / lambda sensor inputGreen / blueCoolant temperature sensor inputGreenMAP sensor inputGreySensor returnsRedPower inputBlackPower returnSource discrepancy: The manual's ECU function list gives the oxygen input loom colour as orange/white, while its separate oxygen-sensor component section gives white/red. Check the actual loom and original manufacturer diagram before identifying that circuit.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Omex 550
The historical OMEM550 controls injection and ignition and uses MAP2000. Manual v3.02 describes throttle-position or manifold-pressure load input, air and coolant temperature sensors, narrowband oxygen feedback, a configurable auxiliary output and fuel and ignition maps. The manual documents crank trigger and distributor-trigger options; identify the sensor and programmed timing configuration. Model-specific Omex manual · Omex engine-management range.
Connector and pinout
The OMEM550 hardware manual v3.02 gives its model-specific ECU pinout in section 13.3 and wiring diagrams in section 13.4. Do not assume that a 500 or 600 loom is interchangeable. Open the exact-model installation or hardware manual.
Software and setup
The historical manual specifies MAP2000; software and communication requirements depend on the hardware and firmware. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.
Compare models and historical identities in the Omex family guide.
Revision 3: Omex 550
The historical OMEM550 controls injection and ignition and uses MAP2000. Manual v3.02 describes throttle-position or manifold-pressure load input, air and coolant temperature sensors, narrowband oxygen feedback, a configurable auxiliary output and fuel and ignition maps. The manual documents crank trigger and distributor-trigger options; identify the sensor and programmed timing configuration. Model-specific Omex manual · Omex engine-management range.
Connector and pinout
The OMEM550 hardware manual v3.02 gives its model-specific ECU pinout in section 13.3 and wiring diagrams in section 13.4. Do not assume that a 500 or 600 loom is interchangeable. Open the exact-model installation or hardware manual.
Software and setup
The historical manual specifies MAP2000; software and communication requirements depend on the hardware and firmware. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.
Compare models and historical identities in the Omex family guide.
Manufacturer loom functions and colours
These functions and loom colours are listed in section 13.3 of the Omex OMEM550 hardware manual v3.02. The accessible text transcription does not preserve the table alignment well enough to verify the individual cavity numbers, so this table identifies wires by colour only. Obtain the original illustrated table from Omex to confirm connector numbering and view.
| Omex loom colour | Documented function |
|---|
| Yellow | Ignition driver 2 output |
| Screened red | Timing / crank-position pickup input |
| Blue | Auxiliary output |
| Orange | Throttle position sensor wiper input |
| Pink | +5 V sensor power output |
| Brown | Injector driver 1 output |
| Green / white | Air temperature sensor input |
| Violet | Ignition driver 1 output |
| White | Injector driver 2 output |
| Orange / white | Oxygen / lambda sensor input |
| Green / blue | Coolant temperature sensor input |
| Green | MAP sensor input |
| Grey | Sensor returns |
| Red | Power input |
| Black | Power return |
Source discrepancy: The manual's ECU function list gives the oxygen input loom colour as orange/white, while its separate oxygen-sensor component section gives white/red. Check the actual loom and original manufacturer diagram before identifying that circuit.