Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Omex standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
The older OMEM500 controls fuel injection and ignition and is mapped with MAP2000. Its hardware manual describes throttle or MAP load sensing, narrowband oxygen feedback, crank or distributor sensing, and an auxiliary low-side output selectable for a fuel-pump relay, tachometer or shift light. It describes high-impedance injectors or appropriately ballasted low-impedance injectors. Model-specific Omex manual · Omex engine-management range.
Connector and pinout
The OMEM500 hardware manual v3.02 contains model-specific ECU connector pinouts in section 13.3 and wiring diagrams in section 13.4. Use that table and the loom connector orientation for this exact model. Open the exact-model installation or hardware manual.
OMEM500 15-way loom connectorSource: Omex OMEM500 hardware manual v3.02, section 13.3, page 29. The manual gives the view at the loom connector; confirm numbering and orientation from its drawing. Wiring colours identify the documented loom and must be checked on modified installations.PinWireFunction1YellowIgnition driver 22Screened redTiming pickup input3BlueAuxiliary output4OrangeThrottle position wiper5Pink5 V sensor supply6BrownInjector driver 17Green/whiteAir temperature8VioletIgnition driver 19WhiteInjector driver 210Orange/whiteLambda input11Green/blueCoolant temperature12GreenMAP input13GreySensor returns14RedPower input15BlackPower returnSoftware and setup
The historical manual specifies MAP2000; software and communication requirements depend on the hardware and firmware. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.
Compare models and historical identities in the Omex family guide.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Omex 500
The older OMEM500 controls fuel injection and ignition and is mapped with MAP2000. Its hardware manual describes throttle or MAP load sensing, narrowband oxygen feedback, crank or distributor sensing, and an auxiliary low-side output selectable for a fuel-pump relay, tachometer or shift light. It describes high-impedance injectors or appropriately ballasted low-impedance injectors. Model-specific Omex manual · Omex engine-management range.
Connector and pinout
The OMEM500 hardware manual v3.02 contains model-specific ECU connector pinouts in section 13.3 and wiring diagrams in section 13.4. Use that table and the loom connector orientation for this exact model. Open the exact-model installation or hardware manual.
Software and setup
The historical manual specifies MAP2000; software and communication requirements depend on the hardware and firmware. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.
Compare models and historical identities in the Omex family guide.
Revision 2: Omex 500
The older OMEM500 controls fuel injection and ignition and is mapped with MAP2000. Its hardware manual describes throttle or MAP load sensing, narrowband oxygen feedback, crank or distributor sensing, and an auxiliary low-side output selectable for a fuel-pump relay, tachometer or shift light. It describes high-impedance injectors or appropriately ballasted low-impedance injectors. Model-specific Omex manual · Omex engine-management range.
Connector and pinout
The OMEM500 hardware manual v3.02 contains model-specific ECU connector pinouts in section 13.3 and wiring diagrams in section 13.4. Use that table and the loom connector orientation for this exact model. Open the exact-model installation or hardware manual.
OMEM500 15-way loom connector
Source: Omex OMEM500 hardware manual v3.02, section 13.3, page 29. The manual gives the view at the loom connector; confirm numbering and orientation from its drawing. Wiring colours identify the documented loom and must be checked on modified installations.
| Pin | Wire | Function |
|---|
| 1 | Yellow | Ignition driver 2 |
| 2 | Screened red | Timing pickup input |
| 3 | Blue | Auxiliary output |
| 4 | Orange | Throttle position wiper |
| 5 | Pink | 5 V sensor supply |
| 6 | Brown | Injector driver 1 |
| 7 | Green/white | Air temperature |
| 8 | Violet | Ignition driver 1 |
| 9 | White | Injector driver 2 |
| 10 | Orange/white | Lambda input |
| 11 | Green/blue | Coolant temperature |
| 12 | Green | MAP input |
| 13 | Grey | Sensor returns |
| 14 | Red | Power input |
| 15 | Black | Power return |
Software and setup
The historical manual specifies MAP2000; software and communication requirements depend on the hardware and firmware. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.
Compare models and historical identities in the Omex family guide.