Removed text is struck through; added text is highlighted.
G4X XtremeX manufacturer photograph: Link ECU. Permission to republish confirmed by the user.
Link G4X XtremeX is a programmable G4X wire-in engine-management ECU. Two loom connectors, electronic throttle, two knock inputs and 11 analogue voltage inputs. The manufacturer's guide identifies digital inputs 9/10 as shared with CAN 2. Link G4X XtremeX quick-start guide.
Model identification and I/O
ItemDocumented detailsECU familyG4XOutputs8 injection and 8 ignition drivesProgrammingPCLink version matched to ECU generation and firmwareConnector and loomSee the exact-model guide, including connector keys, wire-side orientation and optional functions
The manufacturer guidance and wiring identify the hardware; driver counts do not establish injector electrical compatibility or imply all multiplexed pins can be used at the same time.
Model-specific pinout and installation
The G4X XtremeX quick-start guide provides the connector diagrams and installer I/O table. Refer to that version for numbered cavities, wire colours, supply, grounds, driver and sensor connection notes. Loom wire-side and ECU header views are identified on the diagram; do not transfer a pin number from another generation.
Engine applicationsAs a universal wire-in ECU the XtremeX is not tied to an engine. With eight injection and eight ignition drives it is offered for up to eight cylinders or four rotors with sequential injection and direct spark, and with electronic throttle control; retailers do not list direct-injection support (dealer listings).Connector pinoutBoth 34-way loom connectors are drawn, with every cavity indexed, in the Link G4X XtremeX connector pinout.Complete loom connector tablesThe following positions are transcribed from the Link XTREMEX quick-start guide. They are viewed into the ECU header or the wire side of the loom, as illustrated in the source. Unlabelled positions are shown as such, rather than assumed unused. Colours apply to the documented loom; outputs and shared functions depend on ECU hardware version and configuration. Refer to the original for keying, current limits and full installation diagrams.A/B loom connector A — 34-wayPinFunction in guideLoom colour1Injector 4Brown/Orange2Injector 3Brown/Red3Injector 2Brown4Injector 1Brown/Black5+14 VRed6+8 VRed/White7Shield/GroundGreen8Trigger 1Black9Trigger 2Red10Ignition 4Blue/Orange11Ignition 3Blue/Red12Ignition 2Blue/Brown13Ignition 1Blue14Analogue voltage 4White/Black15Temperature 1Yellow16Temperature 2Yellow/Brown17Analogue voltage 1Yellow/Blue18Auxiliary 4Orange19Auxiliary 3Orange/Red20Auxiliary 2Orange/Brown21Auxiliary 1Orange/Black22Analogue voltage 2White/Brown23Digital input 3Grey/Red24Ground outGreen25GroundBlack26Auxiliary 8Orange/Purple27Auxiliary 7Orange/Blue28Auxiliary 6Orange/Green29Auxiliary 5Orange/Yellow30Digital input 1Grey/Black31Digital input 2Grey/Brown32+5 VRed/Blue33Analogue voltage 3Yellow/Black34GroundBlackA/B loom connector B — 34-wayPinFunction in guideLoom colour1Injector 8Brown/Purple2Injector 7Brown/Blue3Injector 6Brown/Green4Injector 5Brown/Yellow5V EthrottleRed6Temperature 3Yellow/Red7Temperature 4Yellow/Orange8Knock 2White9Knock 1White10Ignition 8Blue/Purple11Ignition 7Blue/Black12Ignition 6Blue/Green13Ignition 5Blue/Yellow14Not labelled in guide—15Analogue voltage 6White/Red16Analogue voltage 7White/Orange17Shield/GroundGreen18Auxiliary 9Purple19Digital input 6Grey/Green20Digital input 5Grey/Yellow21Digital input 4Grey/Orange22Ground outGreen23Analogue voltage 8White/Yellow24Analogue voltage 9White/Green25GroundBlack26Auxiliary 10Purple/White27Digital input 10 / CAN 2 highGrey/Purple28Digital input 9 / CAN 2 lowGrey/White29Digital input 8Grey30Digital input 7Grey/Blue31Analogue voltage 10White/Blue32Analogue voltage 11White33Analogue voltage 5Yellow/Green34GroundBlack
Software and further sources
Download software, firmware and full installation help from Link's download centre; identify the ECU generation and installed firmware before choosing a PCLink package. The legacy software list separates G5, G4X and G4+ compatibility. See also Link standalone ECUs.
SourcesLink Engine Management: G4X XtremeX quick-start guide, manufacturer documentation. Accessed 19 November 2026.Automotive Superstore: Link G4X XtremeX wire-in ECU 109-4000 and Torqen: Link ECU G4X XtremeX, dealer listings. Seen in search summary, 19 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Link G4X XtremeX
Link G4X XtremeX is a programmable G4X wire-in engine-management ECU. Two loom connectors, electronic throttle, two knock inputs and 11 analogue voltage inputs. The manufacturer's guide identifies digital inputs 9/10 as shared with CAN 2. Link G4X XtremeX quick-start guide.
Model identification and I/O
Item
Documented details
ECU family
G4X
Outputs
8 injection and 8 ignition drives
Programming
PCLink version matched to ECU generation and firmware
Connector and loom
See the exact-model guide, including connector keys, wire-side orientation and optional functions
The manufacturer guidance and wiring identify the hardware; driver counts do not establish injector electrical compatibility or imply all multiplexed pins can be used at the same time.
Model-specific pinout and installation
The G4X XtremeX quick-start guide provides the connector diagrams and installer I/O table. Refer to that version for numbered cavities, wire colours, supply, grounds, driver and sensor connection notes. Loom wire-side and ECU header views are identified on the diagram; do not transfer a pin number from another generation.
Software and further sources
Download software, firmware and full installation help from Link's download centre; identify the ECU generation and installed firmware before choosing a PCLink package. The legacy software list separates G5, G4X and G4+ compatibility. See also Link standalone ECUs.
Revision 4: Link G4X XtremeXG4X XtremeX manufacturer photograph: Link ECU. Permission to republish confirmed by the user.
Link G4X XtremeX is a programmable G4X wire-in engine-management ECU. Two loom connectors, electronic throttle, two knock inputs and 11 analogue voltage inputs. The manufacturer's guide identifies digital inputs 9/10 as shared with CAN 2. Link G4X XtremeX quick-start guide.
Model identification and I/O
Item
Documented details
ECU family
G4X
Outputs
8 injection and 8 ignition drives
Programming
PCLink version matched to ECU generation and firmware
Connector and loom
See the exact-model guide, including connector keys, wire-side orientation and optional functions
The manufacturer guidance and wiring identify the hardware; driver counts do not establish injector electrical compatibility or imply all multiplexed pins can be used at the same time.
Model-specific pinout and installation
The G4X XtremeX quick-start guide provides the connector diagrams and installer I/O table. Refer to that version for numbered cavities, wire colours, supply, grounds, driver and sensor connection notes. Loom wire-side and ECU header views are identified on the diagram; do not transfer a pin number from another generation.
Engine applications
As a universal wire-in ECU the XtremeX is not tied to an engine. With eight injection and eight ignition drives it is offered for up to eight cylinders or four rotors with sequential injection and direct spark, and with electronic throttle control; retailers do not list direct-injection support (dealer listings).
The following positions are transcribed from the Link XTREMEX quick-start guide. They are viewed into the ECU header or the wire side of the loom, as illustrated in the source. Unlabelled positions are shown as such, rather than assumed unused. Colours apply to the documented loom; outputs and shared functions depend on ECU hardware version and configuration. Refer to the original for keying, current limits and full installation diagrams.
A/B loom connector A — 34-way
Pin
Function in guide
Loom colour
1
Injector 4
Brown/Orange
2
Injector 3
Brown/Red
3
Injector 2
Brown
4
Injector 1
Brown/Black
5
+14 V
Red
6
+8 V
Red/White
7
Shield/Ground
Green
8
Trigger 1
Black
9
Trigger 2
Red
10
Ignition 4
Blue/Orange
11
Ignition 3
Blue/Red
12
Ignition 2
Blue/Brown
13
Ignition 1
Blue
14
Analogue voltage 4
White/Black
15
Temperature 1
Yellow
16
Temperature 2
Yellow/Brown
17
Analogue voltage 1
Yellow/Blue
18
Auxiliary 4
Orange
19
Auxiliary 3
Orange/Red
20
Auxiliary 2
Orange/Brown
21
Auxiliary 1
Orange/Black
22
Analogue voltage 2
White/Brown
23
Digital input 3
Grey/Red
24
Ground out
Green
25
Ground
Black
26
Auxiliary 8
Orange/Purple
27
Auxiliary 7
Orange/Blue
28
Auxiliary 6
Orange/Green
29
Auxiliary 5
Orange/Yellow
30
Digital input 1
Grey/Black
31
Digital input 2
Grey/Brown
32
+5 V
Red/Blue
33
Analogue voltage 3
Yellow/Black
34
Ground
Black
A/B loom connector B — 34-way
Pin
Function in guide
Loom colour
1
Injector 8
Brown/Purple
2
Injector 7
Brown/Blue
3
Injector 6
Brown/Green
4
Injector 5
Brown/Yellow
5
V Ethrottle
Red
6
Temperature 3
Yellow/Red
7
Temperature 4
Yellow/Orange
8
Knock 2
White
9
Knock 1
White
10
Ignition 8
Blue/Purple
11
Ignition 7
Blue/Black
12
Ignition 6
Blue/Green
13
Ignition 5
Blue/Yellow
14
Not labelled in guide
—
15
Analogue voltage 6
White/Red
16
Analogue voltage 7
White/Orange
17
Shield/Ground
Green
18
Auxiliary 9
Purple
19
Digital input 6
Grey/Green
20
Digital input 5
Grey/Yellow
21
Digital input 4
Grey/Orange
22
Ground out
Green
23
Analogue voltage 8
White/Yellow
24
Analogue voltage 9
White/Green
25
Ground
Black
26
Auxiliary 10
Purple/White
27
Digital input 10 / CAN 2 high
Grey/Purple
28
Digital input 9 / CAN 2 low
Grey/White
29
Digital input 8
Grey
30
Digital input 7
Grey/Blue
31
Analogue voltage 10
White/Blue
32
Analogue voltage 11
White
33
Analogue voltage 5
Yellow/Green
34
Ground
Black
Software and further sources
Download software, firmware and full installation help from Link's download centre; identify the ECU generation and installed firmware before choosing a PCLink package. The legacy software list separates G5, G4X and G4+ compatibility. See also Link standalone ECUs.