Removed text is struck through; added text is highlighted.
SCS Delta GDI4 ECU. Image: SCS Delta SXTune hardware reference; reproduced with permission.
SCS Delta GDI4 is a programmable SCS Delta engine-management controller. Legacy GDI4 direct-injection controller with AMPSeal A 776164-1 and B 776163-5. The documented hardware provides four paired high- and low-side injector connections, electronic throttle, pump control, knock inputs and additional PWM/relay outputs. SCS lists it as a legacy unit; do not substitute the GDI6 pinout. SXTune GDI4 hardware reference.
Pinout and connector identification
Connector B B1–B4 are injector 1–4 high side and B13–B16 injector 1–4 low side. B5–B6 are throttle motor, and B7–B8 are fuel-pump drive in the documented configuration. The complete GDI4 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignmentsThese assignments and electrical notes are from the SXTune deltagdi4 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.The source repeats connector B in two tables with differing example application names at several positions, including B18–B20, B29 and B32. The table below reproduces the first source table's application column; those examples must not be treated as fixed configuration.Connectors A and BPinShort NameNameDescriptionApplicationA1VBATTBatteryPower Supply input 6-18VDirect Battery Supply (fuse 15A)A2VKEYIgnitionIgnition Switch inputIgnition Switched Supply (fuse 10A)A3P_GND1Power Ground 1Power GroundPower Ground 1A4OUT1Low Side 13A Open Collector w/recirc diodeHot Soak Relay ControlA5OUT2Low Side 23A Open Collector w/recirc diodeA/C Clutch Relay ControlA6OUT3Low Side 33A Open Collector w/recirc diodePurge Valve ControlA7OUT4Low Side 43A Open Collector w/recirc diodeLambda Heater DriveA8D_GNDHall GroundDigital GroundCrank/Cam Sensors GroundA9CRANKHall InputDigital InputCrank Sensor InputA10CAM1Hall InputDigital InputIntake Cam InputA11TCOOLNTC Input3.16K pull-up to VREFCoolant Temp InputA12TAIRNTC Input3.16K pull-up to VREFCharge Air Temp InputA13IGN1Ignition 1Logic or Power (hardware selected)Ignition Coil 1 OutputA14IGN2Ignition 2Logic or Power (hardware selected)Ignition Coil 2 OutputA15IGN3Ignition 3Logic or Power (hardware selected)Ignition Coil 3 OutputA16IGN4Ignition 4Logic or Power (hardware selected)Ignition Coil 4 OutputA17LINEAR1Analog Input 147k pull-up to VREFFuel Rail Pressure InputA18CAM2Hall InputDigital InputExhaust Cam InputA19A_GND1Analog Ground 1Analog GroundTemp Sensors GroundA20LMBD1Lambda 1 InputWeak bias to 450mVLambda 1 InputA21CAN1HCAN 1H120 Ohm TerminatedCAN 1 HighA22CAN1LCAN 1LCAN 1 LowA23HALL1Hall Input 1Digital InputMAF InputA24OUT5Low Side 53A Open Collector w/recirc diodeMain Relay OutputA25OUT6Low Side 63A Open Collector w/recirc diodeThermostat Control OutputA26OUT7Low Side 73A Open Collector w/recirc diodeIntake Cam PWM OutputA27OUT8Low Side 83A Open Collector w/recirc diodeExhaust Cam PWM OutputA28OUT9Low Side 93A Open Collector w/recirc diodeFan 1 Relay/PWM OutputA29OUT10Low Side 103A Open Collector w/recirc diodeFan 2 Relay/PWM OutputA30A_GND2Analog Ground 2Analog GroundTPS/MAP/MAF GroundA31NTC1NTC Input 13.16K pull-up to VREFGear Cut InputA32LINEAR2Analog Input 247k pull-up to VREFThrottle Position Sensor 1 InputA33LINEAR3Analog Input 347k pull-up to VREFMAP Sensor InputA34VREF1VREF 15V 500mA sensor supply5V Sensor Supply 1A35P_GND2Power Ground 2Power GroundPower Ground 2B1INJ1+Injector 1 +Injector 1 High SideInjector 1 +B2INJ2+Injector 2 +Injector 2 High SideInjector 2 +B3INJ3+Injector 3 +Injector 3 High SideInjector 3 +B4INJ4+Injector 4 +Injector 4 High SideInjector 4 +B5HBRIDGE1+H Bridge M+5A H-BridgeThrottle +B6HBRIDGE1-H Bridge M-5A H-BridgeThrottle -B7HBRIDGE2+Fuel Pump Drive +5A H-BridgeFuel Pump +B8HBRIDGE2-Fuel Pump Drive -5A H-BridgeFuel Pump -B9OUT11Low Side 113A Open Collector w/recirc diodeWastegate Valve OutputB10OUT12Low Side 123A Open Collector w/recirc diodeRecirc Valve OutputB11VREF2VREF 25V 500mA sensor supply5V Sensor Supply 2B12HBRIDGE3+H Bridge 3 M+5A H-BridgeElectronic Turbo Actuator +B13INJ1-Injector 1 -Injector 1 Low SideInjector 1 -B14INJ2-Injector 2 -Injector 2 Low SideInjector 2 -B15INJ3-Injector 3 -Injector 3 Low SideInjector 3 -B16INJ4-Injector 4 -Injector 4 Low SideInjector 4 -B17HALL3Hall Input 3Digital InputWheel Speed Input LRB18HALL4Hall Input 4Digital InputWheel Speed Input RRB19HALL5Hall Input 5Digital InputWheel Speed Input LFB20HALL6Hall Input 6Digital InputWheel Speed Input RFB21KNOCK1Knock 1 +Knock InputKnock Sensor 1 InputB22KNOCK2Knock 2 +Knock InputKnock Sensor 2 InputB23K_GNDKnock GroundDigital GroundKnock Sensor GroundB24HBRIDGE3-H Bridge 3 M-5A H-BridgeElectronic Turbo Actuator -B25LINEAR4Analog Input 447k pull-up to VREFThrottle Position Sensor 2 InputB26LINEAR5Analog Input 547k pull-up to VREFPedal Position Sensor 1 InputB27LINEAR6Analog Input 647k pull-up to VREFPedal Position Sensor 2 InputB28LINEAR7Analog Input 747k pull-up to VREFOil Pressure Sensor InputB29LINEAR8Analog Input 847k pull-up to VREFFuel Line Pressure Sensor InputB30LINEAR9Analog Input 947k pull-up to VREFTraction Control Pot InputB31LINEAR10Analog Input 1047k pull-up to VREFA/C System Pressure InputB32LINEAR11Analog Input 1147k pull-up to VREFBoost Pressure Sensor InputB33NTC2NTC Input 23.16k pull-up to VREFFuel Level InputB34CAN2HCAN 2 H120 Ohm TerminatedCAN 2 HighB35CAN2LCAN 2 LCAN 2 LowPC communications DB9 femalePinName1Ground6CAN High7CAN Low8Battery Voltage
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: SCS Delta GDI4
SCS Delta GDI4 is a programmable SCS Delta engine-management controller. Legacy GDI4 direct-injection controller with AMPSeal A 776164-1 and B 776163-5. The documented hardware provides four paired high- and low-side injector connections, electronic throttle, pump control, knock inputs and additional PWM/relay outputs. SCS lists it as a legacy unit; do not substitute the GDI6 pinout. SXTune GDI4 hardware reference.
Pinout and connector identification
Connector B B1–B4 are injector 1–4 high side and B13–B16 injector 1–4 low side. B5–B6 are throttle motor, and B7–B8 are fuel-pump drive in the documented configuration. The complete GDI4 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
SCS Delta GDI4 is a programmable SCS Delta engine-management controller. Legacy GDI4 direct-injection controller with AMPSeal A 776164-1 and B 776163-5. The documented hardware provides four paired high- and low-side injector connections, electronic throttle, pump control, knock inputs and additional PWM/relay outputs. SCS lists it as a legacy unit; do not substitute the GDI6 pinout. SXTune GDI4 hardware reference.
Pinout and connector identification
Connector B B1–B4 are injector 1–4 high side and B13–B16 injector 1–4 low side. B5–B6 are throttle motor, and B7–B8 are fuel-pump drive in the documented configuration. The complete GDI4 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune deltagdi4 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
The source repeats connector B in two tables with differing example application names at several positions, including B18–B20, B29 and B32. The table below reproduces the first source table's application column; those examples must not be treated as fixed configuration.
Connectors A and B
Pin
Short Name
Name
Description
Application
A1
VBATT
Battery
Power Supply input 6-18V
Direct Battery Supply (fuse 15A)
A2
VKEY
Ignition
Ignition Switch input
Ignition Switched Supply (fuse 10A)
A3
P_GND1
Power Ground 1
Power Ground
Power Ground 1
A4
OUT1
Low Side 1
3A Open Collector w/recirc diode
Hot Soak Relay Control
A5
OUT2
Low Side 2
3A Open Collector w/recirc diode
A/C Clutch Relay Control
A6
OUT3
Low Side 3
3A Open Collector w/recirc diode
Purge Valve Control
A7
OUT4
Low Side 4
3A Open Collector w/recirc diode
Lambda Heater Drive
A8
D_GND
Hall Ground
Digital Ground
Crank/Cam Sensors Ground
A9
CRANK
Hall Input
Digital Input
Crank Sensor Input
A10
CAM1
Hall Input
Digital Input
Intake Cam Input
A11
TCOOL
NTC Input
3.16K pull-up to VREF
Coolant Temp Input
A12
TAIR
NTC Input
3.16K pull-up to VREF
Charge Air Temp Input
A13
IGN1
Ignition 1
Logic or Power (hardware selected)
Ignition Coil 1 Output
A14
IGN2
Ignition 2
Logic or Power (hardware selected)
Ignition Coil 2 Output
A15
IGN3
Ignition 3
Logic or Power (hardware selected)
Ignition Coil 3 Output
A16
IGN4
Ignition 4
Logic or Power (hardware selected)
Ignition Coil 4 Output
A17
LINEAR1
Analog Input 1
47k pull-up to VREF
Fuel Rail Pressure Input
A18
CAM2
Hall Input
Digital Input
Exhaust Cam Input
A19
A_GND1
Analog Ground 1
Analog Ground
Temp Sensors Ground
A20
LMBD1
Lambda 1 Input
Weak bias to 450mV
Lambda 1 Input
A21
CAN1H
CAN 1H
120 Ohm Terminated
CAN 1 High
A22
CAN1L
CAN 1L
CAN 1 Low
A23
HALL1
Hall Input 1
Digital Input
MAF Input
A24
OUT5
Low Side 5
3A Open Collector w/recirc diode
Main Relay Output
A25
OUT6
Low Side 6
3A Open Collector w/recirc diode
Thermostat Control Output
A26
OUT7
Low Side 7
3A Open Collector w/recirc diode
Intake Cam PWM Output
A27
OUT8
Low Side 8
3A Open Collector w/recirc diode
Exhaust Cam PWM Output
A28
OUT9
Low Side 9
3A Open Collector w/recirc diode
Fan 1 Relay/PWM Output
A29
OUT10
Low Side 10
3A Open Collector w/recirc diode
Fan 2 Relay/PWM Output
A30
A_GND2
Analog Ground 2
Analog Ground
TPS/MAP/MAF Ground
A31
NTC1
NTC Input 1
3.16K pull-up to VREF
Gear Cut Input
A32
LINEAR2
Analog Input 2
47k pull-up to VREF
Throttle Position Sensor 1 Input
A33
LINEAR3
Analog Input 3
47k pull-up to VREF
MAP Sensor Input
A34
VREF1
VREF 1
5V 500mA sensor supply
5V Sensor Supply 1
A35
P_GND2
Power Ground 2
Power Ground
Power Ground 2
B1
INJ1+
Injector 1 +
Injector 1 High Side
Injector 1 +
B2
INJ2+
Injector 2 +
Injector 2 High Side
Injector 2 +
B3
INJ3+
Injector 3 +
Injector 3 High Side
Injector 3 +
B4
INJ4+
Injector 4 +
Injector 4 High Side
Injector 4 +
B5
HBRIDGE1+
H Bridge M+
5A H-Bridge
Throttle +
B6
HBRIDGE1-
H Bridge M-
5A H-Bridge
Throttle -
B7
HBRIDGE2+
Fuel Pump Drive +
5A H-Bridge
Fuel Pump +
B8
HBRIDGE2-
Fuel Pump Drive -
5A H-Bridge
Fuel Pump -
B9
OUT11
Low Side 11
3A Open Collector w/recirc diode
Wastegate Valve Output
B10
OUT12
Low Side 12
3A Open Collector w/recirc diode
Recirc Valve Output
B11
VREF2
VREF 2
5V 500mA sensor supply
5V Sensor Supply 2
B12
HBRIDGE3+
H Bridge 3 M+
5A H-Bridge
Electronic Turbo Actuator +
B13
INJ1-
Injector 1 -
Injector 1 Low Side
Injector 1 -
B14
INJ2-
Injector 2 -
Injector 2 Low Side
Injector 2 -
B15
INJ3-
Injector 3 -
Injector 3 Low Side
Injector 3 -
B16
INJ4-
Injector 4 -
Injector 4 Low Side
Injector 4 -
B17
HALL3
Hall Input 3
Digital Input
Wheel Speed Input LR
B18
HALL4
Hall Input 4
Digital Input
Wheel Speed Input RR
B19
HALL5
Hall Input 5
Digital Input
Wheel Speed Input LF
B20
HALL6
Hall Input 6
Digital Input
Wheel Speed Input RF
B21
KNOCK1
Knock 1 +
Knock Input
Knock Sensor 1 Input
B22
KNOCK2
Knock 2 +
Knock Input
Knock Sensor 2 Input
B23
K_GND
Knock Ground
Digital Ground
Knock Sensor Ground
B24
HBRIDGE3-
H Bridge 3 M-
5A H-Bridge
Electronic Turbo Actuator -
B25
LINEAR4
Analog Input 4
47k pull-up to VREF
Throttle Position Sensor 2 Input
B26
LINEAR5
Analog Input 5
47k pull-up to VREF
Pedal Position Sensor 1 Input
B27
LINEAR6
Analog Input 6
47k pull-up to VREF
Pedal Position Sensor 2 Input
B28
LINEAR7
Analog Input 7
47k pull-up to VREF
Oil Pressure Sensor Input
B29
LINEAR8
Analog Input 8
47k pull-up to VREF
Fuel Line Pressure Sensor Input
B30
LINEAR9
Analog Input 9
47k pull-up to VREF
Traction Control Pot Input
B31
LINEAR10
Analog Input 10
47k pull-up to VREF
A/C System Pressure Input
B32
LINEAR11
Analog Input 11
47k pull-up to VREF
Boost Pressure Sensor Input
B33
NTC2
NTC Input 2
3.16k pull-up to VREF
Fuel Level Input
B34
CAN2H
CAN 2 H
120 Ohm Terminated
CAN 2 High
B35
CAN2L
CAN 2 L
CAN 2 Low
PC communications DB9 female
Pin
Name
1
Ground
6
CAN High
7
CAN Low
8
Battery Voltage
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.