Removed text is struck through; added text is highlighted.
SCS Delta 880 ECU. Image: SCS Delta SXTune hardware reference; reproduced with permission.
SCS Delta 880 is a programmable SCS Delta engine-management controller. Legacy two-connector Delta unit listed separately from the 800 in the SXTune hardware archive. The reference shows two throttle bridges, wheel-speed inputs, knock inputs and gearshift-related assignments. Its defaults differ from the 800, so similar-looking plugs do not prove a direct swap. SXTune 880 hardware reference.
Pinout and connector identification
A17 is the gear-position sensor input in the documented application; B9 is a configurable output, B10 is gearshift air-pressure relay, B15 is gear-up solenoid and B16 gear-down solenoid. B1–B4 are the two throttle bridge pairs. These are the documented application functions, not universal settings. The complete 880 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignmentsThese assignments and electrical notes are from the SXTune delta880 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.Main ConnectorPinNameDescriptionNotes1BatteryDirect Battery Supply (15A fuse)Direct Battery Power 6-15V2IgnitionIgnition Switched Supply (10A fuse)Ignition Key Input3Power Ground 1Power GroundPower Ground4Low Side Output 13A Open CollectorInjector 15Low Side Output 23A Open CollectorInjector 26Low Side Output 33A Open CollectorInjector 37Low Side Output 43A Open CollectorInjector 48Crank/Cam GroundDigital GroundCrank/Cam Sensor Ground9Crank InputVR/Hall - Software SelectableCrank Sensor Input10Cam Input 1VR/Hall - Software SelectableInlet Cam Sensor 1 Input11NTC Input 13.16K pull-up to VREFCoolant Temp Input12NTC Input 23.16K pull-up to VREFAir Temp Input13Ignition 1TTL/Power Ignition OutputIgnition 114Ignition 2TTL/Power Ignition OutputIgnition 215Ignition 3TTL/Power Ignition OutputIgnition 316Ignition 4TTL/Power Ignition OutputIgnition 417Analog Input 147k pull-up to VREFGear Position Sensor18Cam Input 2VR/Hall - Software SelectableCam 2 / Wheel Speed19Analog Ground 1Analog GroundAnalog Ground20Lambda 1 InputWeak bias to 450mV0-5V Analog Input21CAN 1H120 Ohm TerminatedTo PC comms DB922CAN 1LTo PC comms DB923Low Side Output 53A Open CollectorMFIO Injector 5 and Lambda 3 Input24Low Side Output 73A Open Collector w/ recirc diodeMain Relay/PWM125Low Side Output 83A Open Collector w/ recirc diodeFuel Pump Relay/PWM226Low Side Output 93A Open Collector w/ recirc diodePWM327Low Side Output 103A Open Collector w/ recirc diodePWM428Low Side Output 113A Open Collector with pull-up to VBATT via diodeTacho Output29Low Side Output 63A Open CollectorMFIO Injector 6 and Lambda 4 Input30Analog Ground 2Analog GroundAnalog Ground31NTC Input 33.16K pull-up to VREFNTC132Analog Input 247k pull-up to VREFTPS133Analog Input 347k pull-up to VREFMAP34VREF500mA 5V supply to sensors5V Reference35Power Ground 2Power GroundPower Ground 2Secondary ConnectorPinNameDescriptionNotesB1H Bridge 1 M+5A H-BridgeThrottle 1 +B2H Bridge 1 M-5A H-BridgeThrottle 1 -B3H Bridge 2 M+5A H-BridgeThrottle 2 +B4H Bridge 2 M-5A H-BridgeThrottle 2 -B5Bipolar Output 13A Hi Side/Lo Side DrivePWM5B6Bipolar Output 23A Hi Side/Lo Side DrivePWM6B7Bipolar Output 33A Hi Side/Lo Side DrivePWM7B8Bipolar Output 43A Hi Side/Lo Side DrivePWM8B9Low Side Output 123A Open CollectorUser Configurable OutputB10Low Side Output 133A Open CollectorGear Shift Air Pressure RelayB11Cam Input 3VR/Hall - Software SelectableCam 3B12Cam Input 4VR/Hall - Software SelectableCam 4B13Ignition 5TTL/PowerShort circuit protection for PowerB14Ignition 6TTL/PowerShort circuit protection for PowerB15Ignition 7TTL/PowerGear Up Solenoid OutputB16Ignition 8TTL/PowerGear Down Solenoid OutputB17Hall Input 1Hall Effect InputWheel Speed LRB18Hall Input 2Hall Effect InputWheel Speed RRB19Hall Input 3Hall Effect InputWheel Speed LFB20Hall Input 4Hall Effect InputWheel Speed RFB21Knock 1 +B22Knock 2 +B23Knock GroundDigital GroundB24Lambda 2 InputWeak bias to 450mVLambda 2B25Analog Input 447k pull-up to VREFTPS2B26Analog Input 547k pull-up to VREFPPS1B27Analog Input 647k pull-up to VREFPPS2B28NTC Input 43.16k pull-up to VREFGear Up Paddle InputB29NTC Input 53.16k pull-up to VREFGear Down Paddle InputB30Analog Input 747k pull-up to VREFOil Pressure Sensor InputB31Analog Input 847k pull-up to VREFClutch Switch InputB32Analog Input 947k pull-up to VREFNeutral Switch InputB33Analog Input 1047k pull-up to VREFGear Shift Air Pressure SensorB34CAN 2L120 Ohm TerminatedB35CAN 2HPC communications DB9 femalePinName1Ground6CAN High7CAN Low8Battery VoltagePC communications DTMPinName1Battery Voltage2Ground3CAN High4CAN Low
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: SCS Delta 880
SCS Delta 880 is a programmable SCS Delta engine-management controller. Legacy two-connector Delta unit listed separately from the 800 in the SXTune hardware archive. The reference shows two throttle bridges, wheel-speed inputs, knock inputs and gearshift-related assignments. Its defaults differ from the 800, so similar-looking plugs do not prove a direct swap. SXTune 880 hardware reference.
Pinout and connector identification
A17 is the gear-position sensor input in the documented application; B9 is a configurable output, B10 is gearshift air-pressure relay, B15 is gear-up solenoid and B16 gear-down solenoid. B1–B4 are the two throttle bridge pairs. These are the documented application functions, not universal settings. The complete 880 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
SCS Delta 880 is a programmable SCS Delta engine-management controller. Legacy two-connector Delta unit listed separately from the 800 in the SXTune hardware archive. The reference shows two throttle bridges, wheel-speed inputs, knock inputs and gearshift-related assignments. Its defaults differ from the 800, so similar-looking plugs do not prove a direct swap. SXTune 880 hardware reference.
Pinout and connector identification
A17 is the gear-position sensor input in the documented application; B9 is a configurable output, B10 is gearshift air-pressure relay, B15 is gear-up solenoid and B16 gear-down solenoid. B1–B4 are the two throttle bridge pairs. These are the documented application functions, not universal settings. The complete 880 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune delta880 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
Main Connector
Pin
Name
Description
Notes
1
Battery
Direct Battery Supply (15A fuse)
Direct Battery Power 6-15V
2
Ignition
Ignition Switched Supply (10A fuse)
Ignition Key Input
3
Power Ground 1
Power Ground
Power Ground
4
Low Side Output 1
3A Open Collector
Injector 1
5
Low Side Output 2
3A Open Collector
Injector 2
6
Low Side Output 3
3A Open Collector
Injector 3
7
Low Side Output 4
3A Open Collector
Injector 4
8
Crank/Cam Ground
Digital Ground
Crank/Cam Sensor Ground
9
Crank Input
VR/Hall - Software Selectable
Crank Sensor Input
10
Cam Input 1
VR/Hall - Software Selectable
Inlet Cam Sensor 1 Input
11
NTC Input 1
3.16K pull-up to VREF
Coolant Temp Input
12
NTC Input 2
3.16K pull-up to VREF
Air Temp Input
13
Ignition 1
TTL/Power Ignition Output
Ignition 1
14
Ignition 2
TTL/Power Ignition Output
Ignition 2
15
Ignition 3
TTL/Power Ignition Output
Ignition 3
16
Ignition 4
TTL/Power Ignition Output
Ignition 4
17
Analog Input 1
47k pull-up to VREF
Gear Position Sensor
18
Cam Input 2
VR/Hall - Software Selectable
Cam 2 / Wheel Speed
19
Analog Ground 1
Analog Ground
Analog Ground
20
Lambda 1 Input
Weak bias to 450mV
0-5V Analog Input
21
CAN 1H
120 Ohm Terminated
To PC comms DB9
22
CAN 1L
To PC comms DB9
23
Low Side Output 5
3A Open Collector
MFIO Injector 5 and Lambda 3 Input
24
Low Side Output 7
3A Open Collector w/ recirc diode
Main Relay/PWM1
25
Low Side Output 8
3A Open Collector w/ recirc diode
Fuel Pump Relay/PWM2
26
Low Side Output 9
3A Open Collector w/ recirc diode
PWM3
27
Low Side Output 10
3A Open Collector w/ recirc diode
PWM4
28
Low Side Output 11
3A Open Collector with pull-up to VBATT via diode
Tacho Output
29
Low Side Output 6
3A Open Collector
MFIO Injector 6 and Lambda 4 Input
30
Analog Ground 2
Analog Ground
Analog Ground
31
NTC Input 3
3.16K pull-up to VREF
NTC1
32
Analog Input 2
47k pull-up to VREF
TPS1
33
Analog Input 3
47k pull-up to VREF
MAP
34
VREF
500mA 5V supply to sensors
5V Reference
35
Power Ground 2
Power Ground
Power Ground 2
Secondary Connector
Pin
Name
Description
Notes
B1
H Bridge 1 M+
5A H-Bridge
Throttle 1 +
B2
H Bridge 1 M-
5A H-Bridge
Throttle 1 -
B3
H Bridge 2 M+
5A H-Bridge
Throttle 2 +
B4
H Bridge 2 M-
5A H-Bridge
Throttle 2 -
B5
Bipolar Output 1
3A Hi Side/Lo Side Drive
PWM5
B6
Bipolar Output 2
3A Hi Side/Lo Side Drive
PWM6
B7
Bipolar Output 3
3A Hi Side/Lo Side Drive
PWM7
B8
Bipolar Output 4
3A Hi Side/Lo Side Drive
PWM8
B9
Low Side Output 12
3A Open Collector
User Configurable Output
B10
Low Side Output 13
3A Open Collector
Gear Shift Air Pressure Relay
B11
Cam Input 3
VR/Hall - Software Selectable
Cam 3
B12
Cam Input 4
VR/Hall - Software Selectable
Cam 4
B13
Ignition 5
TTL/Power
Short circuit protection for Power
B14
Ignition 6
TTL/Power
Short circuit protection for Power
B15
Ignition 7
TTL/Power
Gear Up Solenoid Output
B16
Ignition 8
TTL/Power
Gear Down Solenoid Output
B17
Hall Input 1
Hall Effect Input
Wheel Speed LR
B18
Hall Input 2
Hall Effect Input
Wheel Speed RR
B19
Hall Input 3
Hall Effect Input
Wheel Speed LF
B20
Hall Input 4
Hall Effect Input
Wheel Speed RF
B21
Knock 1 +
B22
Knock 2 +
B23
Knock Ground
Digital Ground
B24
Lambda 2 Input
Weak bias to 450mV
Lambda 2
B25
Analog Input 4
47k pull-up to VREF
TPS2
B26
Analog Input 5
47k pull-up to VREF
PPS1
B27
Analog Input 6
47k pull-up to VREF
PPS2
B28
NTC Input 4
3.16k pull-up to VREF
Gear Up Paddle Input
B29
NTC Input 5
3.16k pull-up to VREF
Gear Down Paddle Input
B30
Analog Input 7
47k pull-up to VREF
Oil Pressure Sensor Input
B31
Analog Input 8
47k pull-up to VREF
Clutch Switch Input
B32
Analog Input 9
47k pull-up to VREF
Neutral Switch Input
B33
Analog Input 10
47k pull-up to VREF
Gear Shift Air Pressure Sensor
B34
CAN 2L
120 Ohm Terminated
B35
CAN 2H
PC communications DB9 female
Pin
Name
1
Ground
6
CAN High
7
CAN Low
8
Battery Voltage
PC communications DTM
Pin
Name
1
Battery Voltage
2
Ground
3
CAN High
4
CAN Low
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.