Removed text is struck through; added text is highlighted.
SCS Delta 800 ECU. Image: SCS Delta SXTune hardware reference; reproduced with permission.
SCS Delta 800 is a programmable SCS Delta engine-management controller. Legacy SCS Delta controller documented with two AMPSeal connectors A 776164-1 and B 776163-4 plus female DB9 CAN connector. The manufacturer pinout shows two H-bridge throttle motor pairs and positions for eight injector and eight ignition outputs, subject to software configuration and output ratings. SXTune 800 hardware reference.
Pinout and connector identification
A1 battery, A2 switched ignition, A3 power ground, A4–A7 injector 1–4, A9 crank and A10 cam 1. On B, B1–B4 are the two H-bridge throttle motor pairs; B9–B10 are injector 7–8 and B13–B16 ignition 5–8. The complete 800 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignmentsThese assignments and electrical notes are from the SXTune delta800 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.Connector APinNameDescriptionNotes1BatteryDirect Battery Supply (15A fuse)Direct Battery Power 6-15V2IgnitionIgnition Switched Supply (10A fuse)Ignition Key Input3Power Ground 1Power GroundPower Ground 14Low Side Output 13A Open CollectorInjector 1 Output5Low Side Output 23A Open CollectorInjector 2 Output6Low Side Output 33A Open CollectorInjector 3 Output7Low Side Output 43A Open CollectorInjector 4 Output8Crank/Cam GroundDigital GroundCrank/Cam Sensor Ground9Crank InputVR/Hall - Software SelectableCrank Sensor Input10Cam Input 1VR/Hall - Software SelectableCam Sensor 1 Input11NTC Input 13.16K pull-up to VREFCoolant Temperature Input12NTC Input 23.16K pull-up to VREFAir Temperature Input13Ignition 1TTL/Power Ignition OutputSoftware Configurable Output14Ignition 2TTL/Power Ignition OutputSoftware Configurable Output15Ignition 3TTL/Power Ignition OutputSoftware Configurable Output16Ignition 4TTL/Power Ignition OutputSoftware Configurable Output17Analog Input 147k pull-up to VREFLinear 1 Input18Cam Input 2VR/Hall - Software SelectableCam Sensor 2 Input19Analog Ground 1Analog GroundAnalog Ground20Lambda 1 InputWeak bias to 450mVLambda Sensor 2 Input21CAN 1H120 Ohm TerminatedTo PC comms DB922CAN 1LTo PC comms DB923Low Side Output 53A Open CollectorAuxiliary 1 / Injector 5 Output24Low Side Output 73A Open Collector w/ recirc diodeMain Relay/PWM125Low Side Output 83A Open Collector w/ recirc diodeFuel Pump Relay/PWM226Low Side Output 93A Open Collector w/ recirc diodePWM3 Output27Low Side Output 103A Open Collector w/ recirc diodePWM4 Output28Low Side Output 113A Open Collector with pull-up to VBATT via diodeTachometer Output29Low Side Output 63A Open CollectorAuxiliary 2 / Injector 6 Output30Analog Ground 2Analog GroundAnalog Sensors Ground31NTC Input 33.16K pull-up to VREFNTC1 Input32Analog Input 247k pull-up to VREFThrottle Position Sensor Input33Analog Input 347k pull-up to VREFManifold Pressure Sensor Input34VREF500mA 5V supply to sensors5V Reference Sensor Supply35Power Ground 2Power GroundPower Ground 2Connector BPinNameDescriptionNotesB1H Bridge 1 M+5A H-BridgeThrottle Motor 1 +B2H Bridge 1 M-5A H-BridgeThrottle Motor 1 -B3H Bridge 2 M+5A H-BridgeThrottle Motor 2 +B4H Bridge 2 M-5A H-BridgeThrottle Motor 2 -B5Bipolar Output 13A Hi Side/Lo Side DrivePWM5 OutputB6Bipolar Output 23A Hi Side/Lo Side DrivePWM6 OutputB7Bipolar Output 33A Hi Side/Lo Side DrivePWM7 OutputB8Bipolar Output 43A Hi Side/Lo Side DrivePWM8 OutputB9Low Side Output 123A Open CollectorInjector 7 OutputB10Low Side Output 133A Open CollectorInjector 8 OutputB11Cam Input 3VR/Hall - Software SelectableCam Sensor 3 InputB12Cam Input 4VR/Hall - Software SelectableCam Sensor 4 InputB13Ignition 5TTL/PowerSoftware Configurable OutputB14Ignition 6TTL/PowerSoftware Configurable OutputB15Ignition 7TTL/PowerShort circuit protection for PowerB16Ignition 8TTL/PowerShort circuit protection for PowerB17Hall Input 1Hall Effect InputWheel Speed LRB18Hall Input 2Hall Effect InputWheel Speed RRB19Hall Input 3Hall Effect InputWheel Speed LFB20Hall Input 4Hall Effect InputWheel Speed RFB21Knock 1 +Knock 1 Signal InputB22Knock 2 +Knock 2 Signal InputB23Knock GroundDigital GroundB24Lambda 2 InputWeak bias to 450mVLambda 2B25Analog Input 447k pull-up to VREFTPS2B26Analog Input 547k pull-up to VREFPPS1B27Analog Input 647k pull-up to VREFPPS2B28NTC Input 43.16k pull-up to VREFNTC2 InputB29NTC Input 53.16k pull-up to VREFNTC3 InputB30Analog Input 747k pull-up to VREFLinear 5 InputB31Analog Input 847k pull-up to VREFLinear 6 InputB32Analog Input 947k pull-up to VREFLinear 7 InputB33Analog Input 1047k pull-up to VREFLinear 8 InputB34CAN 2LCAN 2 Low120 Ohm TerminatedB35CAN 2HCAN 2 HighPC communications DB9 femalePinName1Ground6CAN High7CAN Low8Battery VoltagePC communications DTMPinName1Battery Voltage2Ground3CAN High4CAN Low
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: SCS Delta 800
SCS Delta 800 is a programmable SCS Delta engine-management controller. Legacy SCS Delta controller documented with two AMPSeal connectors A 776164-1 and B 776163-4 plus female DB9 CAN connector. The manufacturer pinout shows two H-bridge throttle motor pairs and positions for eight injector and eight ignition outputs, subject to software configuration and output ratings. SXTune 800 hardware reference.
Pinout and connector identification
A1 battery, A2 switched ignition, A3 power ground, A4–A7 injector 1–4, A9 crank and A10 cam 1. On B, B1–B4 are the two H-bridge throttle motor pairs; B9–B10 are injector 7–8 and B13–B16 ignition 5–8. The complete 800 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
SCS Delta 800 is a programmable SCS Delta engine-management controller. Legacy SCS Delta controller documented with two AMPSeal connectors A 776164-1 and B 776163-4 plus female DB9 CAN connector. The manufacturer pinout shows two H-bridge throttle motor pairs and positions for eight injector and eight ignition outputs, subject to software configuration and output ratings. SXTune 800 hardware reference.
Pinout and connector identification
A1 battery, A2 switched ignition, A3 power ground, A4–A7 injector 1–4, A9 crank and A10 cam 1. On B, B1–B4 are the two H-bridge throttle motor pairs; B9–B10 are injector 7–8 and B13–B16 ignition 5–8. The complete 800 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune delta800 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
Connector A
Pin
Name
Description
Notes
1
Battery
Direct Battery Supply (15A fuse)
Direct Battery Power 6-15V
2
Ignition
Ignition Switched Supply (10A fuse)
Ignition Key Input
3
Power Ground 1
Power Ground
Power Ground 1
4
Low Side Output 1
3A Open Collector
Injector 1 Output
5
Low Side Output 2
3A Open Collector
Injector 2 Output
6
Low Side Output 3
3A Open Collector
Injector 3 Output
7
Low Side Output 4
3A Open Collector
Injector 4 Output
8
Crank/Cam Ground
Digital Ground
Crank/Cam Sensor Ground
9
Crank Input
VR/Hall - Software Selectable
Crank Sensor Input
10
Cam Input 1
VR/Hall - Software Selectable
Cam Sensor 1 Input
11
NTC Input 1
3.16K pull-up to VREF
Coolant Temperature Input
12
NTC Input 2
3.16K pull-up to VREF
Air Temperature Input
13
Ignition 1
TTL/Power Ignition Output
Software Configurable Output
14
Ignition 2
TTL/Power Ignition Output
Software Configurable Output
15
Ignition 3
TTL/Power Ignition Output
Software Configurable Output
16
Ignition 4
TTL/Power Ignition Output
Software Configurable Output
17
Analog Input 1
47k pull-up to VREF
Linear 1 Input
18
Cam Input 2
VR/Hall - Software Selectable
Cam Sensor 2 Input
19
Analog Ground 1
Analog Ground
Analog Ground
20
Lambda 1 Input
Weak bias to 450mV
Lambda Sensor 2 Input
21
CAN 1H
120 Ohm Terminated
To PC comms DB9
22
CAN 1L
To PC comms DB9
23
Low Side Output 5
3A Open Collector
Auxiliary 1 / Injector 5 Output
24
Low Side Output 7
3A Open Collector w/ recirc diode
Main Relay/PWM1
25
Low Side Output 8
3A Open Collector w/ recirc diode
Fuel Pump Relay/PWM2
26
Low Side Output 9
3A Open Collector w/ recirc diode
PWM3 Output
27
Low Side Output 10
3A Open Collector w/ recirc diode
PWM4 Output
28
Low Side Output 11
3A Open Collector with pull-up to VBATT via diode
Tachometer Output
29
Low Side Output 6
3A Open Collector
Auxiliary 2 / Injector 6 Output
30
Analog Ground 2
Analog Ground
Analog Sensors Ground
31
NTC Input 3
3.16K pull-up to VREF
NTC1 Input
32
Analog Input 2
47k pull-up to VREF
Throttle Position Sensor Input
33
Analog Input 3
47k pull-up to VREF
Manifold Pressure Sensor Input
34
VREF
500mA 5V supply to sensors
5V Reference Sensor Supply
35
Power Ground 2
Power Ground
Power Ground 2
Connector B
Pin
Name
Description
Notes
B1
H Bridge 1 M+
5A H-Bridge
Throttle Motor 1 +
B2
H Bridge 1 M-
5A H-Bridge
Throttle Motor 1 -
B3
H Bridge 2 M+
5A H-Bridge
Throttle Motor 2 +
B4
H Bridge 2 M-
5A H-Bridge
Throttle Motor 2 -
B5
Bipolar Output 1
3A Hi Side/Lo Side Drive
PWM5 Output
B6
Bipolar Output 2
3A Hi Side/Lo Side Drive
PWM6 Output
B7
Bipolar Output 3
3A Hi Side/Lo Side Drive
PWM7 Output
B8
Bipolar Output 4
3A Hi Side/Lo Side Drive
PWM8 Output
B9
Low Side Output 12
3A Open Collector
Injector 7 Output
B10
Low Side Output 13
3A Open Collector
Injector 8 Output
B11
Cam Input 3
VR/Hall - Software Selectable
Cam Sensor 3 Input
B12
Cam Input 4
VR/Hall - Software Selectable
Cam Sensor 4 Input
B13
Ignition 5
TTL/Power
Software Configurable Output
B14
Ignition 6
TTL/Power
Software Configurable Output
B15
Ignition 7
TTL/Power
Short circuit protection for Power
B16
Ignition 8
TTL/Power
Short circuit protection for Power
B17
Hall Input 1
Hall Effect Input
Wheel Speed LR
B18
Hall Input 2
Hall Effect Input
Wheel Speed RR
B19
Hall Input 3
Hall Effect Input
Wheel Speed LF
B20
Hall Input 4
Hall Effect Input
Wheel Speed RF
B21
Knock 1 +
Knock 1 Signal Input
B22
Knock 2 +
Knock 2 Signal Input
B23
Knock Ground
Digital Ground
B24
Lambda 2 Input
Weak bias to 450mV
Lambda 2
B25
Analog Input 4
47k pull-up to VREF
TPS2
B26
Analog Input 5
47k pull-up to VREF
PPS1
B27
Analog Input 6
47k pull-up to VREF
PPS2
B28
NTC Input 4
3.16k pull-up to VREF
NTC2 Input
B29
NTC Input 5
3.16k pull-up to VREF
NTC3 Input
B30
Analog Input 7
47k pull-up to VREF
Linear 5 Input
B31
Analog Input 8
47k pull-up to VREF
Linear 6 Input
B32
Analog Input 9
47k pull-up to VREF
Linear 7 Input
B33
Analog Input 10
47k pull-up to VREF
Linear 8 Input
B34
CAN 2L
CAN 2 Low
120 Ohm Terminated
B35
CAN 2H
CAN 2 High
PC communications DB9 female
Pin
Name
1
Ground
6
CAN High
7
CAN Low
8
Battery Voltage
PC communications DTM
Pin
Name
1
Battery Voltage
2
Ground
3
CAN High
4
CAN Low
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.