Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 5

Removed text is struck through; added text is highlighted.

Image: Canems, Injection ECU manual, release 2.03, reproduced from The Wedge Shop mirror with permission.

Canems engine management includes a programmable Injection ECU for fuel and ignition control. The historical release 2.03 guide describes up to eight cylinders with wasted spark and four injector drivers; this information does not establish a complete model catalogue.

Individual ECU referenceCanems Injection ECU contains model details, revision comparisons, applications and the full sourced 30-way table. A separate 6- and 8-cylinder ignition-only ECU is documented in its own manual. The full range of Canems hardware and historic variants is not established by the available sources.

Known systems and applications

Canems Injection ECU, documented in releases 2.03 and 2.17 of the installation manual.Rover V8 conversion kit — an application package using a Canems ECU, rather than a separately verified ECU model name.

See Canems Injection ECU manual, release 2.03 and Rover V8 installation guide. A Rover V8 kit page shows the installation.

Injection ECU: hardware and operating scopeThe Canems release 2.03 manual describes a programmable ECU with four high-current injector and four ignition outputs for up to eight-cylinder applications using wasted spark. Four-cylinder injection is described as semi-sequential. Ignition can be used without injection on carburetted engines. The manual describes software-selectable MAP or throttle-based load and 1, 2 or 3 bar MAP sensors.The 2.03 release describes two fuel and ignition maps with 180 sites each; a later Canems release 2.17 manual describes 252 sites. These are manual/software releases, not verified separate ECU model names. Confirm firmware and installation details with the supplier rather than assuming every unit has every feature in the later manual.Documented features and tuningTwo switchable fuel and ignition maps, programmable speed and load sites and real-time mapping.Crank/cam input, injector phasing, staging, transient enrichment and battery-voltage compensation. Staged injector wiring can depend on the firmware file.Programmable dwell, soft and hard speed limiting, main relay and auxiliary outputs; refer to the ECU's actual output ratings.Release 2.17 lists optional knock control and internal data logging; those options should not be assumed fitted to all units.Canems' release 2.17 manual specifies an ABS housing, 30-way connector, RS232 with optional USB, a 7–18 V negative-earth supply and four high-current injector and ignition outputs. It quotes 10 A per injector and ignition output, but its wiring chapter says low-impedance injectors require suitable series ballast resistors. The source also explains RPM signal, throttle, temperatures, relay control and wiring tests. Release 2.17 manual.Applications and identificationThe 14CUX Rover V8 package and pre-serpentine Rover V8 package are conversion kits with application-specific looms, sensors and base maps. Their names describe applications; they are not established here as separate ECU hardware model names. The 2.03 manual also documents development for siamese-port multi-point injection; that claim does not make a generic map suitable for every A-series installation.Canems has also documented an ignition ECU for six- and eight-cylinder engines. It is a related ignition-only controller, not evidence that the fuel-and-ignition pinout below can be transferred to it.

Injection ECU pinout — manual release 2.03

Thirty-way connector, positions 1A–3K. Use the numbered connector diagram in the manual to establish viewing orientation; this table is for the specific documented ECU and release. Serial connections are preconnected from the factory in this guide.

PinFunction1AInjector earth1BInjector bank 11CInjector bank 21DInjector bank 31EInjector bank 41FIgnition output 41GIgnition output 31HIgnition output 21JIgnition output 11KIgnition earth2AMap switching input2BAir temperature2CCoolant temperature2DThrottle position2EMAP signal2FOxygen sensor 12GOxygen sensor 22H5 V reference2JMain relay output2KOutput 2 (PWM capable)3AECU earth3B12 V supply3CCrank sensor earth and shielding3DCrank sensor signal3ECam / road speed signal3FSerial ground3GSerial receive3HSerial transmit3JOutput 13KTachometer

Confirm the exact ECU, hardware revision and connector orientation before wiring. Configurable functions and electrical limits are model-dependent; consult the linked original diagrams.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Canems standalone engine management

Canems engine management includes a programmable Injection ECU for fuel and ignition control. The historical release 2.03 guide describes up to eight cylinders with wasted spark and four injector drivers; this information does not establish a complete model catalogue.

Known systems and applications

  • Canems Injection ECU, documented in releases 2.03 and 2.17 of the installation manual.
  • Rover V8 conversion kit — an application package using a Canems ECU, rather than a separately verified ECU model name.

See Canems Injection ECU manual, release 2.03 and Rover V8 installation guide. A Rover V8 kit page shows the installation.

Injection ECU pinout — manual release 2.03

Thirty-way connector, positions 1A–3K. Use the numbered connector diagram in the manual to establish viewing orientation; this table is for the specific documented ECU and release. Serial connections are preconnected from the factory in this guide.

PinFunction
1AInjector earth
1BInjector bank 1
1CInjector bank 2
1DInjector bank 3
1EInjector bank 4
1FIgnition output 4
1GIgnition output 3
1HIgnition output 2
1JIgnition output 1
1KIgnition earth
2AMap switching input
2BAir temperature
2CCoolant temperature
2DThrottle position
2EMAP signal
2FOxygen sensor 1
2GOxygen sensor 2
2H5 V reference
2JMain relay output
2KOutput 2 (PWM capable)
3AECU earth
3B12 V supply
3CCrank sensor earth and shielding
3DCrank sensor signal
3ECam / road speed signal
3FSerial ground
3GSerial receive
3HSerial transmit
3JOutput 1
3KTachometer

Confirm the exact ECU, hardware revision and connector orientation before wiring. Configurable functions and electrical limits are model-dependent; consult the linked original diagrams.

Revision 5: Canems standalone engine management

Canems Injection ECU with Injection Tuner software, illustrated on the release 2.03 manual cover

Image: Canems, Injection ECU manual, release 2.03, reproduced from The Wedge Shop mirror with permission.

Canems engine management includes a programmable Injection ECU for fuel and ignition control. The historical release 2.03 guide describes up to eight cylinders with wasted spark and four injector drivers; this information does not establish a complete model catalogue.

Individual ECU reference

Canems Injection ECU contains model details, revision comparisons, applications and the full sourced 30-way table. A separate 6- and 8-cylinder ignition-only ECU is documented in its own manual. The full range of Canems hardware and historic variants is not established by the available sources.

Known systems and applications

  • Canems Injection ECU, documented in releases 2.03 and 2.17 of the installation manual.
  • Rover V8 conversion kit — an application package using a Canems ECU, rather than a separately verified ECU model name.

See Canems Injection ECU manual, release 2.03 and Rover V8 installation guide. A Rover V8 kit page shows the installation.

Injection ECU: hardware and operating scope

The Canems release 2.03 manual describes a programmable ECU with four high-current injector and four ignition outputs for up to eight-cylinder applications using wasted spark. Four-cylinder injection is described as semi-sequential. Ignition can be used without injection on carburetted engines. The manual describes software-selectable MAP or throttle-based load and 1, 2 or 3 bar MAP sensors.

The 2.03 release describes two fuel and ignition maps with 180 sites each; a later Canems release 2.17 manual describes 252 sites. These are manual/software releases, not verified separate ECU model names. Confirm firmware and installation details with the supplier rather than assuming every unit has every feature in the later manual.

Documented features and tuning

  • Two switchable fuel and ignition maps, programmable speed and load sites and real-time mapping.
  • Crank/cam input, injector phasing, staging, transient enrichment and battery-voltage compensation. Staged injector wiring can depend on the firmware file.
  • Programmable dwell, soft and hard speed limiting, main relay and auxiliary outputs; refer to the ECU's actual output ratings.
  • Release 2.17 lists optional knock control and internal data logging; those options should not be assumed fitted to all units.

Canems' release 2.17 manual specifies an ABS housing, 30-way connector, RS232 with optional USB, a 7–18 V negative-earth supply and four high-current injector and ignition outputs. It quotes 10 A per injector and ignition output, but its wiring chapter says low-impedance injectors require suitable series ballast resistors. The source also explains RPM signal, throttle, temperatures, relay control and wiring tests. Release 2.17 manual.

Applications and identification

The 14CUX Rover V8 package and pre-serpentine Rover V8 package are conversion kits with application-specific looms, sensors and base maps. Their names describe applications; they are not established here as separate ECU hardware model names. The 2.03 manual also documents development for siamese-port multi-point injection; that claim does not make a generic map suitable for every A-series installation.

Canems has also documented an ignition ECU for six- and eight-cylinder engines. It is a related ignition-only controller, not evidence that the fuel-and-ignition pinout below can be transferred to it.

Injection ECU pinout — manual release 2.03

Thirty-way connector, positions 1A–3K. Use the numbered connector diagram in the manual to establish viewing orientation; this table is for the specific documented ECU and release. Serial connections are preconnected from the factory in this guide.

PinFunction
1AInjector earth
1BInjector bank 1
1CInjector bank 2
1DInjector bank 3
1EInjector bank 4
1FIgnition output 4
1GIgnition output 3
1HIgnition output 2
1JIgnition output 1
1KIgnition earth
2AMap switching input
2BAir temperature
2CCoolant temperature
2DThrottle position
2EMAP signal
2FOxygen sensor 1
2GOxygen sensor 2
2H5 V reference
2JMain relay output
2KOutput 2 (PWM capable)
3AECU earth
3B12 V supply
3CCrank sensor earth and shielding
3DCrank sensor signal
3ECam / road speed signal
3FSerial ground
3GSerial receive
3HSerial transmit
3JOutput 1
3KTachometer

Confirm the exact ECU, hardware revision and connector orientation before wiring. Configurable functions and electrical limits are model-dependent; consult the linked original diagrams.