Scope: the S4 M-box
This article describes the throttle-airflow and backup-load discussion for the Audi S4 2.7T M-box, identified by S4Wiki as 8D0907551M. It is a diagnostic reference, not a recommendation to disconnect the MAF or operate without fault detection. Map names, signal meanings and fallback logic must be checked in the identified ECU software. A separate Bosch ME7.3.1H Alfa function sheet uses some of the same signal names, but does not establish identical M-box logic.
Two ways of describing incoming air
The MAF path measures air passing the hot-film sensor. The throttle path estimates flow using throttle position and the applicable air-path model. The M-box source calls the latter alpha-N and describes it as a fallback if the primary MAF signal is unavailable. The two paths are not two independent physical flow meters.
| Example signal | What to check |
|---|---|
mshfm_w | MAF-derived mass flow and its conversion; establish units in the logger. |
msdk_w | Throttle-path airflow estimate; interpret with the model and its learned state. |
wdkba, engine speed | Throttle and RPM conditions at the same time as the airflow signals. |
pvdks_w, pus_w | Pre-throttle and ambient pressure in the cited logger definitions, with their correct units. |
Compare like units and reasonably stable operating points first. Transients, sampling or filtering differences, purge or other air paths, leaks, MAF conversion and throttle-model calibration can all affect the relationship. A mismatch is a reason to investigate these possibilities; its shape alone does not prove one particular map is wrong. Record fault codes and adaptations before resetting anything. ME7Logger alias list; Bosch ME7.3.1H Alfa function sheet, BGMSZS and EGFE signal descriptions.
WDKUGDN and throttle flow
For the M-box, S4Wiki describes WDKUGDN as a speed-dependent angle at the transition into an effectively unthrottled range. Its reported pressure-ratio threshold of 0.95 is specific to that documented implementation. KFMSNWDK and KFWDKMSN have separate roles in the throttle-flow relationships; check the function and axis definitions for the actual image before treating a curve as a correction.
Do not confuse this M-box transition with sonic choked flow. The MxT ME7 guide calls WDKUGDN a choke point, while the M-box reference distinguishes the two. NASA describes choked flow as the condition in which flow through a restriction reaches Mach 1 at its smallest area. The physical terms and the ECU’s transition should be evaluated separately. S4Wiki Alpha-N, revision 5321; NASA Glenn: mass-flow choking.
The Tuning Database ME7 guide groups KFWDKMSN with fuel enrichment. Bosch's Audi 132 kW ME7.1 function sheet instead describes it as the inverse of a throttle-flow map, and a separate ME7.3.1H Alfa sheet labels it a desired throttle-angle map. These are related reference examples, not an independent verification of the complete M-box implementation. See ME7 map names and definition checks.
What the pressure-ratio curve represents. A NefMoto discussion asks whether KLAF needs a new shape for a larger throttle or turbo. In the separate Audi 132 kW ME7.1 BGMSZS description, KLAF is a normalised flow characteristic addressed by downstream-to-upstream throttle pressure ratio; opening area, upstream pressure and temperature have their own roles. That document describes a sonic-flow region below about 0.528 and a distinct near-unthrottled transition at about 0.95. These refer to different phenomena in that application. Identify the function and pressure locations before treating a physically derived curve as a hardware-size multiplier; check the exact ECU rather than copying this example's values.
Selecting a different electronic throttle body
Diameter alone does not establish interchangeability. The Bosch Motorsport electronic throttle data sheet lists bodies from 32 to 82 mm, including a 52 mm F02U.V01.184-02 and an 82 mm 0280.750.101. These examples demonstrate the range of hardware available; the sheet does not establish that either is a compatible M-box or other ME7 replacement.
Identify both original and proposed part numbers, mounting and sealing, plate movement and spring rest position. Check the exact connector and pin functions, sensor supply and both feedback tracks across travel, motor wiring and electrical characteristics against the ECU's requirements. Even a matching plug or successful adaptation does not prove electrical, control or airflow-model compatibility. A different effective opening area can also change the relationship between angle and airflow; investigate the matched software's throttle model rather than applying a generic bore-area multiplier.
After a supported replacement, use the applicable vehicle procedure to perform and verify throttle basic settings. Ross-Tech's alignment guide gives group 060 for its listed VW/Audi drive-by-wire examples, with different steps for KW-1281 and KWP-2000/CAN, and identifies prerequisites. Confirm the protocol, fault status and procedure for the particular car; completing alignment learns positions and does not validate an unproven conversion.
Check the function, not the abbreviation
MxT describes FUEREG as fuel adaptation in this discussion. The M-box reference instead identifies it as charge control, and Bosch’s separate ME7.3.1H Alfa sheet also describes a charge controller. Neither is evidence that a WDKUGDN change simply switches closed-loop lambda control off. Determine the actual flags and functions in the ECU being investigated; do not reset learned values or change a transition curve merely to hide a part-throttle airflow difference.
For a heavily modified M-box example involving high wastegate cracking pressure and disputed part-throttle behavior, see ME7 torque intervention during rapid acceleration. That case illustrates why measured pre-throttle pressure, modelled manifold pressure, their requests and fault-driven interventions need separate interpretation.
Sources and attribution
Based on S4Wiki contributors’ Alpha-N, revision 5321, Creative Commons Attribution 4.0; adapted, reorganised and qualified by Tuning Wiki. M-box software behaviour is reported by that source and has not been independently reproduced here. Additional tool context comes from TracqiTechnology/MxT contributors’ ME7 Calibration Guide, rewritten for this page; Apache License 2.0, full text. The Bosch function sheet cited above is for a different ME7.3.1H Alfa application.
Related: ME7 fueling and MAF calibration · ME7 torque, load and boost control · Adaptations and calibration drift.