Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Bosch Motronic 7
Applies to
Bosch ME7.1, Bosch ME7.5
Tool groups
None
Manufacturers
Audi, Volkswagen

Scope: follow the timing path

These examples concern VAG ME7.1/ME7.5 and reported modified 1.8T or 2.7T applications. An irregular ignition trace can reflect cylinder-specific correction, active torque control, a changing base request, operating conditions or a logging artefact. It is not by itself proof of knock, anti-judder intervention or a faulty timing map. Identify the ECU, calibration, hardware, fuel, drivetrain and logger definition first.

The Bosch Audi 132 kW ME7.1 description calls ARMD a torque-based anti-jerk function. Its documented signals include B_ar for the active condition and dmar_w for the anti-jerk torque contribution. That example does not prove identical logic or scaling in every ME7 file.

Record related signals together

GroupExamples where definedWhy it helps
Operating stateRPM, gear, vehicle speed, pedal, throttle, clutch, brake and fault statesSeparate steady acceleration, shift, take-up and pedal transitions.
Air and torqueRequested and actual load, pressure request and measured pressure, torque request and relevant limitsIdentify where demand and the delivered or modelled response diverge.
Ignition pathzwgru, zwbas, zwsol, zwist, zwout, where availableCompare stages using the exact function and logger definition; an ECU output variable is not an independent combustion measurement.
Cylinder and control statePer-cylinder knock corrections, B_ar, dmar_w, relevant idle or shift statesCompare the timing event with correction and intervention magnitude, not an isolated flag.

Check channel source, bank or cylinder, units, signedness, resolution and sample rate. A different or improperly defined channel can produce a convincing but misleading plot. Capture before and after the event and use a manageable set of channels so that important transitions are sampled adequately. The ME7Logger alias list distinguishes internal zwist from ignition output zwout; match both to the specific ECU.

One shape can have several explanations

In a timing-oscillation thread, a tuner reported an improvement on one car after correcting its torque model; the follow-up described a high-load/torque-map mismatch. Other cars in the same discussion had different suspected paths. The reported outcome is not proof that a single table causes all timing oscillation.

In a separate anti-judder investigation, a contributor traced a varying torque contribution and initially reported a fix after several changes, but then reported continuing intervention. Later contributors noted that some apparent output oscillation could reflect the logger sampling different cylinder outputs with different corrections. Treat either as a hypothesis until the matched signals and definitions support it.

Another participant in the later discussion found behaviour associated with a different anti-jerk map than expected. Bosch's cited function lists separate normal, steady-state and dashpot-related thresholds. A similarly named map or an active B_ar alone does not establish which path produced a particular timing change; compare dmar_w, timing stages and state through the event.

Interpret before changing the calibration

  1. Check the event against actual cylinder corrections and, if available, cylinder-specific ignition output. Differences between cylinders, logger multiplexing or timing alignment can make an overall trace look like a sawtooth.
  2. If the torque-related ignition request changes first, inspect the request, permitted and estimated torque/load, boost response and any active anti-jerk or other intervention. If a base stage changes first, investigate its inputs, cam state, load and temperature instead.
  3. Check the underlying air, fuel, knock and mechanical condition. Do not copy addresses or blank maps from another ECU. Anti-jerk can improve low-speed drivability; participants in the same thread discuss increased low-load bucking when it is removed.

Compare repeatable events at similar gear, load, temperatures and fuel, then recheck surrounding operating conditions after a justified change. Related: ignition and knock reference, torque intervention during rapid acceleration and knock logging and leading cylinders. Forum outcomes are attributed reports and have not been independently reproduced by this wiki.