Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Delphi DCM
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 5

Removed text is struck through; added text is highlighted.

Identity and scope

Delphi DCM 1.2 is a diesel common-rail control unit. Renault's fault-finding document MR-413-X44-13B000 identifies DCM1.2 injection, program 4D and diagnostic versions 48, 4C, 50, 54, 58 and 5C. It covers specified K9K engines and vehicle lines; the program and diagnostic version define the document's scope rather than every ECU bearing DCM 1.2. Renault fault-finding manual, pages 13B-2 and 13B-25.

ProcessorDelphi's 2007 generation table describes DCM 1.2 as 16-bit electronics. The AutoTuner ECU compatibility list of 28 October 2026 (tool compatibility listing) gives the microcontroller of its DCM1.2 entry as the ST10F280, a 16-bit STMicroelectronics part of the C166 family. This is a tool vendor's statement; the flash and EEPROM devices are not given there, and the entry covers the tool's listed vehicles rather than every DCM 1.2 board.

Recorded applications

Renault's manual names Clio III, Modus, Megane II / Scenic II, New Twingo and Kangoo 2, with K9K 718, 724, 740, 750, 752, 766, 768, 800, 802 and 812 in its overall scope. This is not a claim that every listed engine occurs in every listed vehicle. A historical Alientech K-Suite list identifies DCM1.2 on 2005 and 2006 Dacia Logan examples with the Renault K9K 790 engine. Alientech K-Suite vehicle list (PDF mirror).Snap-on's 19.2 diagnostic coverage guide lists both DCM 1.2 and DCM 3.4 for Dacia Logan 2009–2012 K9K 1.5 diesel, alongside other systems. The listing describes diagnostic coverage and shows why the model, year and engine family alone are insufficient to identify the installed controller. Snap-on 19.2 vehicle coverage guide (PDF mirror, 40 MB). See also Delphi DCM 3.4.Renault's manual names Clio III, Modus, Megane II / Scenic II, New Twingo and Kangoo 2, with K9K 718, 724, 740, 750, 752, 766, 768, 800, 802 and 812 in its overall scope. This is not a claim that every listed engine occurs in every listed vehicle. Alientech separately lists DCM1.2 for the Renault K9K 790 in Dacia vehicles built from 2005 to 2010. Alientech K-Suite 4.40 release.Sun's 18.4 diagnostic guide lists both DCM 1.2 and DCM 3.4 for Dacia Logan 2009–2012 K9K 1.5 diesel, alongside other systems. The listing describes diagnostic coverage and shows why the model, year and engine family alone are insufficient to identify the installed controller. Sun vehicle coverage guide. See also Delphi DCM 3.4.

Injector correction and replacement

For the Renault manual's program 4D and stated diagnostic versions, injector-specific C2I correction values are recorded on each injector and entered into the ECU. Renault specifies updating the value when an injector is replaced and describes saving ECU operating data before replacement or reprogramming. Follow the exact vehicle procedure and current diagnostic instructions.

That Renault document identifies cylinder 1 at the flywheel end. Numbering conventions in another manufacturer's system must not be substituted for the relevant vehicle's instructions. The manual also describes immobiliser and configuration steps when an ECU is replaced; identical family names alone do not establish interchangeability.

Bench connection pinoutBench-connection pins for this unit are drawn in Delphi DCM 1.2 bench connection pinout.

Sources

Renault, DCM 1.2 injection fault-finding manual MR-413-X44-13B000, program 4D, Vdiag 48, 4C, 50, 54, 58 and 5C: manual mirror, pages 13B-2 and 13B-23–26. Accessed 17 November 2026.Alientech, K-Suite vehicle list (PDF mirror): DCM1.2 and Dacia K9K 790 examples. Historical tool coverage; verify current support.Snap-on, 19.2 vehicle coverage guide (PDF mirror, 40 MB), April 2019, Dacia engine management applications. Historical diagnostic coverage; not a definitive build record.AutoTuner, ECU compatibility list (PDF export, 28 October 2026): DCM1.2 with ST10F280. Accessed 19 November 2026.Renault, DCM 1.2 injection fault-finding manual MR-413-X44-13B000, program 4D, Vdiag 48, 4C, 50, 54, 58 and 5C: manual mirror, pages 13B-2 and 13B-23–26. Accessed 17 November 2026.Alientech, K-Suite 4.40 release, 23 June 2021: DCM1.2 and Dacia K9K 790 example. Historical tool coverage; verify current support.Sun Workshop Solutions, 18.4 vehicle coverage guide, Dacia engine management applications. Historical diagnostic coverage; not a definitive build record.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Delphi DCM 1.2

Identity and scope

Delphi DCM 1.2 is a diesel common-rail control unit. Renault's fault-finding document MR-413-X44-13B000 identifies DCM1.2 injection, program 4D and diagnostic versions 48, 4C, 50, 54, 58 and 5C. It covers specified K9K engines and vehicle lines; the program and diagnostic version define the document's scope rather than every ECU bearing DCM 1.2. Renault fault-finding manual, pages 13B-2 and 13B-25.

Recorded applications

Renault's manual names Clio III, Modus, Megane II / Scenic II, New Twingo and Kangoo 2, with K9K 718, 724, 740, 750, 752, 766, 768, 800, 802 and 812 in its overall scope. This is not a claim that every listed engine occurs in every listed vehicle. Alientech separately lists DCM1.2 for the Renault K9K 790 in Dacia vehicles built from 2005 to 2010. Alientech K-Suite 4.40 release.

Sun's 18.4 diagnostic guide lists both DCM 1.2 and DCM 3.4 for Dacia Logan 2009–2012 K9K 1.5 diesel, alongside other systems. The listing describes diagnostic coverage and shows why the model, year and engine family alone are insufficient to identify the installed controller. Sun vehicle coverage guide. See also Delphi DCM 3.4.

Injector correction and replacement

For the Renault manual's program 4D and stated diagnostic versions, injector-specific C2I correction values are recorded on each injector and entered into the ECU. Renault specifies updating the value when an injector is replaced and describes saving ECU operating data before replacement or reprogramming. Follow the exact vehicle procedure and current diagnostic instructions.

That Renault document identifies cylinder 1 at the flywheel end. Numbering conventions in another manufacturer's system must not be substituted for the relevant vehicle's instructions. The manual also describes immobiliser and configuration steps when an ECU is replaced; identical family names alone do not establish interchangeability.

Sources

  • Renault, DCM 1.2 injection fault-finding manual MR-413-X44-13B000, program 4D, Vdiag 48, 4C, 50, 54, 58 and 5C: manual mirror, pages 13B-2 and 13B-23–26. Accessed 17 November 2026.
  • Alientech, K-Suite 4.40 release, 23 June 2021: DCM1.2 and Dacia K9K 790 example. Historical tool coverage; verify current support.
  • Sun Workshop Solutions, 18.4 vehicle coverage guide, Dacia engine management applications. Historical diagnostic coverage; not a definitive build record.
Revision 5: Delphi DCM 1.2

Identity and scope

Delphi DCM 1.2 is a diesel common-rail control unit. Renault's fault-finding document MR-413-X44-13B000 identifies DCM1.2 injection, program 4D and diagnostic versions 48, 4C, 50, 54, 58 and 5C. It covers specified K9K engines and vehicle lines; the program and diagnostic version define the document's scope rather than every ECU bearing DCM 1.2. Renault fault-finding manual, pages 13B-2 and 13B-25.

Processor

Delphi's 2007 generation table describes DCM 1.2 as 16-bit electronics. The AutoTuner ECU compatibility list of 28 October 2026 (tool compatibility listing) gives the microcontroller of its DCM1.2 entry as the ST10F280, a 16-bit STMicroelectronics part of the C166 family. This is a tool vendor's statement; the flash and EEPROM devices are not given there, and the entry covers the tool's listed vehicles rather than every DCM 1.2 board.

Recorded applications

Renault's manual names Clio III, Modus, Megane II / Scenic II, New Twingo and Kangoo 2, with K9K 718, 724, 740, 750, 752, 766, 768, 800, 802 and 812 in its overall scope. This is not a claim that every listed engine occurs in every listed vehicle. A historical Alientech K-Suite list identifies DCM1.2 on 2005 and 2006 Dacia Logan examples with the Renault K9K 790 engine. Alientech K-Suite vehicle list (PDF mirror).

Snap-on's 19.2 diagnostic coverage guide lists both DCM 1.2 and DCM 3.4 for Dacia Logan 2009–2012 K9K 1.5 diesel, alongside other systems. The listing describes diagnostic coverage and shows why the model, year and engine family alone are insufficient to identify the installed controller. Snap-on 19.2 vehicle coverage guide (PDF mirror, 40 MB). See also Delphi DCM 3.4.

Injector correction and replacement

For the Renault manual's program 4D and stated diagnostic versions, injector-specific C2I correction values are recorded on each injector and entered into the ECU. Renault specifies updating the value when an injector is replaced and describes saving ECU operating data before replacement or reprogramming. Follow the exact vehicle procedure and current diagnostic instructions.

That Renault document identifies cylinder 1 at the flywheel end. Numbering conventions in another manufacturer's system must not be substituted for the relevant vehicle's instructions. The manual also describes immobiliser and configuration steps when an ECU is replaced; identical family names alone do not establish interchangeability.

Bench connection pinout

Bench-connection pins for this unit are drawn in Delphi DCM 1.2 bench connection pinout.

Sources

  • Renault, DCM 1.2 injection fault-finding manual MR-413-X44-13B000, program 4D, Vdiag 48, 4C, 50, 54, 58 and 5C: manual mirror, pages 13B-2 and 13B-23–26. Accessed 17 November 2026.
  • Alientech, K-Suite vehicle list (PDF mirror): DCM1.2 and Dacia K9K 790 examples. Historical tool coverage; verify current support.
  • Snap-on, 19.2 vehicle coverage guide (PDF mirror, 40 MB), April 2019, Dacia engine management applications. Historical diagnostic coverage; not a definitive build record.
  • AutoTuner, ECU compatibility list (PDF export, 28 October 2026): DCM1.2 with ST10F280. Accessed 19 November 2026.