Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Bosch EDC16
Applies to
Bosch EDC16, Bosch EDC16CP34, Bosch EDC16CP34 CRAFTER, Bosch EDC16U1, Bosch EDC16U31, Bosch EDC16U34
Tool groups
None
Manufacturers
Audi, SEAT, Škoda, Volkswagen

Scope and identification

Identify the engine code, ECU hardware/software, turbocharger and actuator before interpreting a boost-control map or log. This guide compares the documented examples below. It does not assign one actuator or a set of map addresses to every U1, U31, U34 or CP34. Use the VAG identification guide to separate Bosch EDC16, Siemens PPD and later controllers.

Documented control arrangements

ApplicationManufacturer evidenceDiagnostic consequence
BKD 2.0 TDI, EDC16 unit-injector exampleVW identifies N75 as the charge-pressure control solenoid in the solenoid-valve block. SSP 316, printed pages 5 and 20–21.Identify the actual valve, tubing and turbo assembly; an electrical command to a solenoid is not a measured vane position.
BJJ/BJK/BJL/BJM Crafter 2.5 TDI, EDC16 C common railThe diagram shows N75 controlling a vacuum capsule and variable guide vanes, with G31/G42 pressure/temperature feedback. SSP 371, printed pages 6–7 and 36–38, French edition.Check vacuum supply, valve/control path and pneumatic actuator as appropriate to this installation. Common rail does not imply an electric turbo actuator.
BMK Phaeton / BKS Touareg 3.0 V6 TDI, EDC16 C common railVW shows an electric vane-positioning motor and turbocharger control unit J724. SSP 350, printed pages 5 and 28–29.Use the correct electrical actuator, supply, communication and position tests. A procedure for a vacuum capsule does not transfer to this assembly.

Calibration implication: establish the meaning, polarity, units and operating mode of the command in this software. “More duty” is not a universal instruction to close the vanes or increase boost. A displayed command and actual actuator movement are separate evidence.

Separate request, feedback and operating state

Capture boost request and actual pressure with RPM, pedal, ambient pressure, intake temperature, air mass and the available actuator command/feedback. Also record fuel quantity, faults and relevant torque interventions. Confirm the pressure reference and sensor scaling using the logging guide; compare the transition into load with the later steady region.

For the documented Crafter system, VW says failure of the charge-pressure signal disables charge-pressure control and substantially reduces output. It separately describes N75 failure leaving its vacuum capsule without vacuum, with spring return to a reduced-boost state. Those failure descriptions belong to this system; a limp-mode log should not be interpreted as the healthy calibration's normal control response. SSP 371, printed pages 37–38.

Overboost and underboost describe a deviation

  • P0234, limit exceeded: Ross-Tech lists hose faults, N75, G31 and a sticking/faulty turbo among possible causes. Select the relevant vehicle tests rather than treating the code as proof that the boost request needs changing. Ross-Tech: P0234.
  • P0299, control range not reached: Ross-Tech lists pipe/leak and charge-control faults, turbo faults and possible exhaust restriction. The page also contains other engine-specific branches; use the branch applicable to the actual vehicle. Ross-Tech: P0299.

Preserve the fault record and compare the pressure deviation with the control command. An initial overshoot, sustained high-RPM pressure rise and persistent underboost are different patterns. The same symptom can arise from a command, feedback or mechanical problem; diagnose the control path before revising protection thresholds.

A practical isolation sequence

  1. Verify the file/calibration identity and pressure units. Check sensor plausibility against the correct service criteria before a loaded test.
  2. Inspect the charge-air path, connections and actuator control path for the installed arrangement. Use the manufacturer's pressure, vacuum, wiring and actuator procedures with their limits.
  3. Use supported output tests or basic settings only for that exact engine/software. Establish actual movement/feedback; do not infer full travel from a changing duty-cycle value.
  4. Review request, actual pressure, air, fuel and temperature together. If a modification is involved, compare with a known baseline under matching conditions. Record what the test ruled out before changing maps.

This sequence is editorial diagnostic guidance. It does not supply a universal vacuum value, actuator travel, duty-cycle direction or boost-deviation margin.

Preserve actuator calibration

Garrett's installation guidance says not to alter a turbo's calibration or minimum vane-open setting. Its electronic-actuator guidance warns that forcing the arm or rod of its self-blocking geared actuators can damage the gears. Identify the turbo and follow its specified test method; adjustment by trial and error can invalidate the intended relationship between command and flow. Garrett installation guide, part 1; part 2.

Reviewing the BKC discussion

Reported discussion: NefMoto's 2015–16 BKC 105 / 03G906016CC thread concerns a reported Audi A3 and recommends checking overshoot and high-RPM creep. Its smoke-based reassurance about EGT is not accompanied by measured temperature or turbo-speed validation. It does not establish a universal BKC torque, boost or thermal limit.

In VW's BMK/BKS example, G235 measures exhaust temperature upstream of the turbo and excessive temperature causes output reduction. This is direct evidence of a separate thermal-protection input on that installation; it does not establish a sensor arrangement or threshold for BKC. SSP 350, printed page 29. For calibration assessment, visible smoke, boost tracking, temperature and turbo-speed margin answer different questions. Retain protection and obtain the evidence appropriate to the fitted hardware.

Evidence and review status

Reviewed 16 November 2026. VW training documents are manufacturer material on independent mirrors and describe historical installations, not current repair instructions. Ross-Tech and Garrett provide diagnostic/equipment guidance. The BKC thread was read through publicly indexed text because direct NefMoto access is blocked; its binary, full software version and claimed results were not independently verified. Test sequences and calibration implications above are editorial reasoning.