Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Bosch Motronic 7
Applies to
Bosch ME7.1, Bosch ME7.5
Tool groups
None
Manufacturers
Audi, Volkswagen

Scope and symptom

Use this guide for VAG ME7.1/ME7.5 port-injection examples after identifying the software, injector type, fuel pressure, sensor arrangement and intake hardware. Calibration names and the order of control states vary. Cold starting, after-start warm-up and a throttle opening are distinct events even when they occur on the same drive.

An injector can deliver approximately the desired steady-state mass while its spray pattern, position and atomisation change how fuel wets the intake surfaces. A transient model may need to account for fuel entering and leaving this wall film as airflow and temperature change. The NefMoto EV14 discussion describes these mechanisms and contributors' different experiences; it does not establish one correction or a universal direction of adjustment.

What the reported cases show

In a cold-start and larger-injector thread, the owner later reported that cold starting and running improved after changing injectors and several related calibration settings together. That outcome makes injector suitability and calibration useful lines of inquiry, but the changes do not isolate a single cause. Another warm-up discussion compares slower cold lambda control with warm behavior and leaves the precise cause open. Neither report proves that a particular injector or map is inherently unsuitable in every installation.

Distinguish the operating phases

  1. Before and during cranking: note soak time, ambient and coolant temperatures, battery voltage and fuel-pressure behavior. A hard start needs a different investigation from a stumble after the engine has caught.
  2. After-start and warm-up: record elapsed time, speed, coolant and intake temperatures, lambda request, measurement and control status. Sensor warm-up and commanded enrichment can change the interpretation.
  3. Steady warm idle and light load: check fuel pressure, air and exhaust leaks, injector data and adaptations. This gives a baseline before judging a transient.
  4. Throttle opening and closing: compare similar small, repeatable transitions at cold and warm temperatures. Log throttle, speed, load or air mass, injection time where available, requested and measured lambda, and control status. Include vehicle speed and gear when relevant.

Align the channels in time and allow for exhaust transport and sensor response. A slow or delayed lambda signal can obscure a brief event; exhaust leaks or misfire can also make an oxygen-based reading misleading. Do not infer the cause or a map change from one lean-looking spike alone.

When a cam change is only a correlation. In a separate Porsche 996 Turbo ME7.8.4 discussion, an owner initially linked a lean-looking stumble to cam changeover. Later observations included similar events without a cam change; the owner ultimately reported improved warm behaviour after several fueling and torque-model revisions, while colder-weather testing remained outstanding. This is a different ECU and a multi-change owner report, not proof of one cause or a calibration recipe for VAG ME7. Compare the event at the same cam state as well as across the transition, and inspect steady fueling and torque intervention. For the separate effect of misfire on an oxygen reading, see ME7 misfire and lean lambda log diagnosis.

Do not read one start multiplier as total fuel. A stock 1.8T ME7.5 discussion illustrates approximate cold-start and after-start enrichment against engine revolutions since first injection using FKSTT, FNSSM and KFFWL. The author explicitly omitted other influences and noted that changing coolant temperature alters the warm-up contribution. Treat the graphs as an illustration, not the total commanded fuel or a universal setting. Identify each actual axis and control state, and compare temperature, fuel pressure, injection time and lambda-sensor readiness where available.

A cold crank and a throttle blip are different tests. In a 1.8T ME7.5 report, cold cranking became longer after an injector change; the owner used latency data from a different injector, suspected excess start fuel and reported improvement after a start-related calibration change. Neither the mixture during cranking nor the root cause was independently established, so the report is not a map-value recipe. Verify the exact injector data and compare voltage, fuel pressure, soak temperature and the start event.

In a separate modified 1.8T discussion, an owner reported a lean-looking tip-in from idle and immediate improvement after changing an ESUK-related parameter; their partially converted speed-density setup and other changes remained in question. An improvement in one transient does not validate the entire air or fuel model. Compare measured and requested lambda with response delay and state, and verify the baseline before attributing an event to a single wall-film function.

Investigating calibration

First confirm the injector's actual part, pressure, electrical characteristics, physical seating, spray direction and applicable calibration. The injector-change discussion identifies the ME7 ESUK transient-compensation function and discusses temperature-dependent wall-film behavior; map names, axes and active conditions need a matching function description and definition. It is a reason to investigate transient compensation, not a replacement for measurement or a justification for copying somebody else's map values.

Compare matched changes and retain a known baseline. If a remedy helps one temperature or transition, repeat at the other relevant conditions and check that steady fueling has not moved unexpectedly. Related pages: ME7 injector changes and idle diagnosis, cold start and warm-up and overrun and return to throttle. Forum examples are reported outcomes, not independent test results.

If the fuel contains a high or varying ethanol fraction, also see ME7 ethanol blends and flex-fuel logging for blend identification, cold-start evidence and sensor-state checks.

When the transition starts from overrun, see ME7 overrun fuel cut and injector log signals for the distinction between calculated injector time and final suppression.