Scope: the S4 M-box
This article describes the throttle-airflow and backup-load discussion for the Audi S4 2.7T M-box, identified by S4Wiki as 8D0907551M. It is a diagnostic reference, not a recommendation to disconnect the MAF or operate without fault detection. Map names, signal meanings and fallback logic must be checked in the identified ECU software. A separate Bosch ME7.3.1H Alfa function sheet uses some of the same signal names, but does not establish identical M-box logic.
Two ways of describing incoming air
The MAF path measures air passing the hot-film sensor. The throttle path estimates flow using throttle position and the applicable air-path model. The M-box source calls the latter alpha-N and describes it as a fallback if the primary MAF signal is unavailable. The two paths are not two independent physical flow meters.
| Example signal | What to check |
|---|---|
mshfm_w | MAF-derived mass flow and its conversion; establish units in the logger. |
msdk_w | Throttle-path airflow estimate; interpret with the model and its learned state. |
wdkba, engine speed | Throttle and RPM conditions at the same time as the airflow signals. |
pvdks_w, pus_w | Pre-throttle and ambient pressure in the cited logger definitions, with their correct units. |
Compare like units and reasonably stable operating points first. Transients, sampling or filtering differences, purge or other air paths, leaks, MAF conversion and throttle-model calibration can all affect the relationship. A mismatch is a reason to investigate these possibilities; its shape alone does not prove one particular map is wrong. Record fault codes and adaptations before resetting anything. ME7Logger alias list; Bosch ME7.3.1H Alfa function sheet, BGMSZS and EGFE signal descriptions.
WDKUGDN and throttle flow
For the M-box, S4Wiki describes WDKUGDN as a speed-dependent angle at the transition into an effectively unthrottled range. Its reported pressure-ratio threshold of 0.95 is specific to that documented implementation. KFMSNWDK and KFWDKMSN have separate roles in the throttle-flow relationships; check the function and axis definitions for the actual image before treating a curve as a correction.
Do not confuse this M-box transition with sonic choked flow. The MxT ME7 guide calls WDKUGDN a choke point, while the M-box reference distinguishes the two. NASA describes choked flow as the condition in which flow through a restriction reaches Mach 1 at its smallest area. The physical terms and the ECU’s transition should be evaluated separately. S4Wiki Alpha-N, revision 5321; NASA Glenn: mass-flow choking.
The Tuning Database ME7 guide groups KFWDKMSN with fuel enrichment. Bosch's Audi 132 kW ME7.1 function sheet instead describes it as the inverse of a throttle-flow map, and a separate ME7.3.1H Alfa sheet labels it a desired throttle-angle map. These are related reference examples, not an independent verification of the complete M-box implementation. See ME7 map names and definition checks.
Check the function, not the abbreviation
MxT describes FUEREG as fuel adaptation in this discussion. The M-box reference instead identifies it as charge control, and Bosch’s separate ME7.3.1H Alfa sheet also describes a charge controller. Neither is evidence that a WDKUGDN change simply switches closed-loop lambda control off. Determine the actual flags and functions in the ECU being investigated; do not reset learned values or change a transition curve merely to hide a part-throttle airflow difference.
For a heavily modified M-box example involving high wastegate cracking pressure and disputed part-throttle behavior, see ME7 torque intervention during rapid acceleration. That case illustrates why measured pre-throttle pressure, modelled manifold pressure, their requests and fault-driven interventions need separate interpretation.
Sources and attribution
Based on S4Wiki contributors’ Alpha-N, revision 5321, Creative Commons Attribution 4.0; adapted, reorganised and qualified by Tuning Wiki. M-box software behaviour is reported by that source and has not been independently reproduced here. Additional tool context comes from TracqiTechnology/MxT contributors’ ME7 Calibration Guide, rewritten for this page; Apache License 2.0, full text. The Bosch function sheet cited above is for a different ME7.3.1H Alfa application.
Related: ME7 fueling and MAF calibration · ME7 torque, load and boost control · Adaptations and calibration drift.