Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Bosch Motronic 7
Applies to
Bosch ME7.1, Bosch ME7.5
Tool groups
None
Manufacturers
Audi, Volkswagen

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Why a good lambda trace is not the whole answer

This guide applies to the VAG ME7.1 and ME7.5 port-injection examples discussed in the sources. Identify the exact ECU, MAF and housing, injectors, fuel and pressure-regulator arrangement. Air leaks, exhaust leaks, fuel supply, sensor calibration and the adaptation state must also be considered.

In a NefMoto discussion of injectors without a data sheet, the author explicitly assumes the rest of the system is already characterised. Later replies challenge the idea that meeting one lambda target identifies which of the air or fuel calibrations is correct. A good measured mixture at one point shows their combined effect there; it does not uniquely measure either part.

Illustration, not engine data: suppose a simplified model expects 100 normalised units of air and commands 100 matching units of fuel. If actual air is 110 and the injector delivers 110 fuel units, the actual air-to-fuel ratio still matches the target even though actual air and injector delivery are both 10% above the model's assumed values. On ME7 the incorrect air estimate can also move calculated load and the operating points used by other functions. This deliberately simplified arithmetic does not reproduce the ECU's full calculations.

Compare operating points without changing the question

ComparisonWhat it can help investigate Warm idle before and after a controlled auxiliary-load changeDoes feedback change at similar RPM but a different air and fuel demand? Record voltage and throttle as well: a load change is not an isolated injector test. Stable light-load points over several speedsLook for repeatable patterns with airflow, load and pulse width. A changing MAF transfer error, injector non-linearity or a leak can overlap. Similar operation at different supply voltagesCompare voltage and injector-time behavior only when the fuel pressure and other conditions are comparable. A voltage-correlated change suggests a check, not a complete latency curve. Separate banks where supportedCompare sensors, leaks and injector behavior before making a global correction; an average can conceal opposing bank errors.

Retain requested and actual lambda, the active lambda-control condition, short-term correction, learned adaptations, RPM, load, MAF voltage and mass, injector-time signals, battery voltage, temperatures and pressure where available. Confirm units, scaling, sampling and software-specific definitions. Compare steady points first and review transients separately. A recent adaptation reset or a small short-term correction after learning is not evidence that the base calibration is correct.

Separate flow, offset and short-pulse behavior

The forum method compares different load and speed conditions, but its proposed values rely on assumptions about the rest of the system and are not a substitute for an injector test. Obtain the exact injector's flow and voltage/pressure data, or characterise it at relevant differential pressures, voltages and pulse widths. Injector Dynamics' GM characterisation example demonstrates why flow, offset and short-pulse non-linearity are distinct; its GM tables and example numbers are not ME7 map definitions.

KRKTE, TVUB and corrections such as FKKVS have different roles in the discussed strategies. The separate KFLF discussion contains changing opinions about which correction to use. Identify the physical source and the active function before applying a correction elsewhere to conceal it. A large high-load error also warrants fuel-pressure and injector-capacity checks; it is not proof of either one.

See ME7 injector changes and idle diagnosis, ME7 MAF and lambda log review and cold and transient fueling. Forum methods are attributed opinions; the wiki has not reproduced them on a vehicle.

For a worked comparison of pressure across the injector and regulator reference behavior, see ME7 fuel pressure and injector differential pressure.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: ME7 identifying injector and MAF errors from logs

Why a good lambda trace is not the whole answer

This guide applies to the VAG ME7.1 and ME7.5 port-injection examples discussed in the sources. Identify the exact ECU, MAF and housing, injectors, fuel and pressure-regulator arrangement. Air leaks, exhaust leaks, fuel supply, sensor calibration and the adaptation state must also be considered.

In a NefMoto discussion of injectors without a data sheet, the author explicitly assumes the rest of the system is already characterised. Later replies challenge the idea that meeting one lambda target identifies which of the air or fuel calibrations is correct. A good measured mixture at one point shows their combined effect there; it does not uniquely measure either part.

Illustration, not engine data: suppose a simplified model expects 100 normalised units of air and commands 100 matching units of fuel. If actual air is 110 and the injector delivers 110 fuel units, the actual air-to-fuel ratio still matches the target even though actual air and injector delivery are both 10% above the model's assumed values. On ME7 the incorrect air estimate can also move calculated load and the operating points used by other functions. This deliberately simplified arithmetic does not reproduce the ECU's full calculations.

Compare operating points without changing the question

ComparisonWhat it can help investigate
Warm idle before and after a controlled auxiliary-load changeDoes feedback change at similar RPM but a different air and fuel demand? Record voltage and throttle as well: a load change is not an isolated injector test.
Stable light-load points over several speedsLook for repeatable patterns with airflow, load and pulse width. A changing MAF transfer error, injector non-linearity or a leak can overlap.
Similar operation at different supply voltagesCompare voltage and injector-time behavior only when the fuel pressure and other conditions are comparable. A voltage-correlated change suggests a check, not a complete latency curve.
Separate banks where supportedCompare sensors, leaks and injector behavior before making a global correction; an average can conceal opposing bank errors.

Retain requested and actual lambda, the active lambda-control condition, short-term correction, learned adaptations, RPM, load, MAF voltage and mass, injector-time signals, battery voltage, temperatures and pressure where available. Confirm units, scaling, sampling and software-specific definitions. Compare steady points first and review transients separately. A recent adaptation reset or a small short-term correction after learning is not evidence that the base calibration is correct.

Separate flow, offset and short-pulse behavior

The forum method compares different load and speed conditions, but its proposed values rely on assumptions about the rest of the system and are not a substitute for an injector test. Obtain the exact injector's flow and voltage/pressure data, or characterise it at relevant differential pressures, voltages and pulse widths. Injector Dynamics' GM characterisation example demonstrates why flow, offset and short-pulse non-linearity are distinct; its GM tables and example numbers are not ME7 map definitions.

KRKTE, TVUB and corrections such as FKKVS have different roles in the discussed strategies. The separate KFLF discussion contains changing opinions about which correction to use. Identify the physical source and the active function before applying a correction elsewhere to conceal it. A large high-load error also warrants fuel-pressure and injector-capacity checks; it is not proof of either one.

See ME7 injector changes and idle diagnosis, ME7 MAF and lambda log review and cold and transient fueling. Forum methods are attributed opinions; the wiki has not reproduced them on a vehicle.

For a worked comparison of pressure across the injector and regulator reference behavior, see ME7 fuel pressure and injector differential pressure.

Revision 2: ME7 identifying injector and MAF errors from logs

Why a good lambda trace is not the whole answer

This guide applies to the VAG ME7.1 and ME7.5 port-injection examples discussed in the sources. Identify the exact ECU, MAF and housing, injectors, fuel and pressure-regulator arrangement. Air leaks, exhaust leaks, fuel supply, sensor calibration and the adaptation state must also be considered.

In a NefMoto discussion of injectors without a data sheet, the author explicitly assumes the rest of the system is already characterised. Later replies challenge the idea that meeting one lambda target identifies which of the air or fuel calibrations is correct. A good measured mixture at one point shows their combined effect there; it does not uniquely measure either part.

Illustration, not engine data: suppose a simplified model expects 100 normalised units of air and commands 100 matching units of fuel. If actual air is 110 and the injector delivers 110 fuel units, the actual air-to-fuel ratio still matches the target even though actual air and injector delivery are both 10% above the model's assumed values. On ME7 the incorrect air estimate can also move calculated load and the operating points used by other functions. This deliberately simplified arithmetic does not reproduce the ECU's full calculations.

Compare operating points without changing the question

ComparisonWhat it can help investigate
Warm idle before and after a controlled auxiliary-load changeDoes feedback change at similar RPM but a different air and fuel demand? Record voltage and throttle as well: a load change is not an isolated injector test.
Stable light-load points over several speedsLook for repeatable patterns with airflow, load and pulse width. A changing MAF transfer error, injector non-linearity or a leak can overlap.
Similar operation at different supply voltagesCompare voltage and injector-time behavior only when the fuel pressure and other conditions are comparable. A voltage-correlated change suggests a check, not a complete latency curve.
Separate banks where supportedCompare sensors, leaks and injector behavior before making a global correction; an average can conceal opposing bank errors.

Retain requested and actual lambda, the active lambda-control condition, short-term correction, learned adaptations, RPM, load, MAF voltage and mass, injector-time signals, battery voltage, temperatures and pressure where available. Confirm units, scaling, sampling and software-specific definitions. Compare steady points first and review transients separately. A recent adaptation reset or a small short-term correction after learning is not evidence that the base calibration is correct.

Separate flow, offset and short-pulse behavior

The forum method compares different load and speed conditions, but its proposed values rely on assumptions about the rest of the system and are not a substitute for an injector test. Obtain the exact injector's flow and voltage/pressure data, or characterise it at relevant differential pressures, voltages and pulse widths. Injector Dynamics' GM characterisation example demonstrates why flow, offset and short-pulse non-linearity are distinct; its GM tables and example numbers are not ME7 map definitions.

KRKTE, TVUB and corrections such as FKKVS have different roles in the discussed strategies. The separate KFLF discussion contains changing opinions about which correction to use. Identify the physical source and the active function before applying a correction elsewhere to conceal it. A large high-load error also warrants fuel-pressure and injector-capacity checks; it is not proof of either one.

See ME7 injector changes and idle diagnosis, ME7 MAF and lambda log review and cold and transient fueling. Forum methods are attributed opinions; the wiki has not reproduced them on a vehicle.

For a worked comparison of pressure across the injector and regulator reference behavior, see ME7 fuel pressure and injector differential pressure.