Page organisation in this revision
- Page type
- Technical article
- Subject
- Supercharging
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Part of the supercharger types and Eaton model guide.
What it is
The M24 is a compact early Eaton Roots-type unit. Its approximately 0.393-litre rotor displacement describes one blower rotation, not the size of the engine. Eaton reported its introduction on the Brazilian Ford Fiesta.
SpecificationDetailRotor familyM-series Roots-type; nominal positive displacementNominal supercharger displacement24 in³ ≈ 0.393 L / rotor revolution
Displacement: the blower volume is nominal air volume moved per rotor revolution. The engine figures below are cylinder capacity. Actual delivered air depends on speed, pressure, leakage and temperature.
Cars, engines and examples
These are documented examples, not a complete fitment catalogue. Factory equipment and aftermarket conversions are identified separately. Confirm market, vehicle, engine code and complete part number.
Vehicle and periodEngine displacement and typeInstallation and identificationEvidenceFord Fiesta Supercharger, Brazil, 2002 launch1.0 L Zetec Rocam inline-fourFactory example. Eaton's 2002 annual report names the Fiesta M24; a parts manufacturer's application list separately identifies the 1.0 Supercharger engine.Eaton; Tuper
Design and application
The small rotor capacity can suit compact-engine projects, but the mounting, inlet and drive were engineered for the donor. It is not automatically suitable for every 1.0-litre engine. Verify the housing, pulley, bypass and clearance before planning a swap.
Identification, maintenance and upgrades
Inspect rotor coating and case for contact, the input bearings, seals and coupling, and the bypass where fitted. Obtain lubrication and speed limits for the actual part number; do not transfer them from a larger M-series or a TVS unit.
Before increasing speed or load, match the complete fuel, ignition, cooling, bypass and engine-calibration package to the intended use. Refer to the exact supplier's specifications; a generic pulley size or blower displacement is not a safe operating limit.
Sources
Eaton 2002 annual report: M24 and Brazilian Fiesta. Accessed 2026-11-14.
Tuper Ford application catalogue: Fiesta 1.0 Supercharger. Accessed 2026-11-14.
FSAE research: M24 nominal displacement. Accessed 2026-11-14.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Eaton M24 supercharger
Part of the supercharger types and Eaton model guide.
What it is
The M24 is a compact early Eaton Roots-type unit. Its approximately 0.393-litre rotor displacement describes one blower rotation, not the size of the engine. Eaton reported its introduction on the Brazilian Ford Fiesta.
| Specification | Detail |
|---|
| Rotor family | M-series Roots-type; nominal positive displacement |
|---|
| Nominal supercharger displacement | 24 in³ ≈ 0.393 L / rotor revolution |
|---|
Displacement: the blower volume is nominal air volume moved per rotor revolution. The engine figures below are cylinder capacity. Actual delivered air depends on speed, pressure, leakage and temperature.
Cars, engines and examples
These are documented examples, not a complete fitment catalogue. Factory equipment and aftermarket conversions are identified separately. Confirm market, vehicle, engine code and complete part number.
| Vehicle and period | Engine displacement and type | Installation and identification | Evidence |
|---|
| Ford Fiesta Supercharger, Brazil, 2002 launch | 1.0 L Zetec Rocam inline-four | Factory example. Eaton's 2002 annual report names the Fiesta M24; a parts manufacturer's application list separately identifies the 1.0 Supercharger engine. | Eaton; Tuper |
Design and application
The small rotor capacity can suit compact-engine projects, but the mounting, inlet and drive were engineered for the donor. It is not automatically suitable for every 1.0-litre engine. Verify the housing, pulley, bypass and clearance before planning a swap.
Identification, maintenance and upgrades
Inspect rotor coating and case for contact, the input bearings, seals and coupling, and the bypass where fitted. Obtain lubrication and speed limits for the actual part number; do not transfer them from a larger M-series or a TVS unit.
Before increasing speed or load, match the complete fuel, ignition, cooling, bypass and engine-calibration package to the intended use. Refer to the exact supplier's specifications; a generic pulley size or blower displacement is not a safe operating limit.
Sources
Revision 1: Eaton M24 supercharger
Part of the supercharger types and Eaton model guide.
What it is
The M24 is a compact early Eaton Roots-type unit. Its approximately 0.393-litre rotor displacement describes one blower rotation, not the size of the engine. Eaton reported its introduction on the Brazilian Ford Fiesta.
| Specification | Detail |
|---|
| Rotor family | M-series Roots-type; nominal positive displacement |
|---|
| Nominal supercharger displacement | 24 in³ ≈ 0.393 L / rotor revolution |
|---|
Displacement: the blower volume is nominal air volume moved per rotor revolution. The engine figures below are cylinder capacity. Actual delivered air depends on speed, pressure, leakage and temperature.
Cars, engines and examples
These are documented examples, not a complete fitment catalogue. Factory equipment and aftermarket conversions are identified separately. Confirm market, vehicle, engine code and complete part number.
| Vehicle and period | Engine displacement and type | Installation and identification | Evidence |
|---|
| Ford Fiesta Supercharger, Brazil, 2002 launch | 1.0 L Zetec Rocam inline-four | Factory example. Eaton's 2002 annual report names the Fiesta M24; a parts manufacturer's application list separately identifies the 1.0 Supercharger engine. | Eaton; Tuper |
Design and application
The small rotor capacity can suit compact-engine projects, but the mounting, inlet and drive were engineered for the donor. It is not automatically suitable for every 1.0-litre engine. Verify the housing, pulley, bypass and clearance before planning a swap.
Identification, maintenance and upgrades
Inspect rotor coating and case for contact, the input bearings, seals and coupling, and the bypass where fitted. Obtain lubrication and speed limits for the actual part number; do not transfer them from a larger M-series or a TVS unit.
Before increasing speed or load, match the complete fuel, ignition, cooling, bypass and engine-calibration package to the intended use. Refer to the exact supplier's specifications; a generic pulley size or blower displacement is not a safe operating limit.
Sources