Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Supercharging
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

What a supercharger does

A mechanically driven supercharger moves or compresses intake air using power taken from the engine, commonly through a belt, gears or a traction drive. It can provide response without waiting for an exhaust turbine to accelerate, but the drive consumes crankshaft power and the compressed air becomes hot. The best choice depends on the engine's desired torque curve, available packaging, heat rejection and use.

Roots-type

A Roots blower is a positive-displacement air mover. Lobed rotors carry air from inlet to outlet; pressure builds principally against the resistance downstream. Modern examples can have twisted lobes, as in Eaton's TVS. Air delivery per revolution is related to the displacement of the rotor set, although leakage and efficiency change with speed and pressure. It can deliver useful low-speed response when correctly sized, while heat, drive power and the engine's airflow still limit the system.

Twin-screw

A twin-screw is also a positive-displacement machine, but its meshing rotors progressively reduce the volume of trapped air inside the case. Whipple describes that internal compression before discharge into the manifold. Rotor shape and porting distinguish the design; the presence of a helical or twisted rotor by itself does not prove a blower has the same internal compression. Roots and twin-screw units are both often described as positive displacement, but they are not mechanically identical.

Centrifugal

A centrifugal supercharger uses an impeller and compressor housing rather like the compressor side of a turbo. A belt and internal step-up drive turn the impeller at high speed. With a fixed drive ratio, its boost usually rises strongly with engine speed, so its torque delivery can differ from a positive-displacement unit. Rotrex uses a planetary traction drive and a specified fluid circuit; other makes use different drives and lubrication. Match the unit by its compressor map and speed limits, not by a generic boost number.

Drive ratio and pulleys

At a fixed crank pulley diameter and engine speed, fitting a smaller pulley to the supercharger makes its input turn faster. For a belt drive with negligible slip, input speed is approximately engine speed multiplied by crank pulley diameter divided by supercharger pulley diameter. Where there is an internal step-up, multiply input speed by that ratio to estimate impeller speed. Check the manufacturer's definition of each limit: input and impeller speed are not interchangeable.

Calculate speed at the highest engine speed the engine can reach, and stay within the exact model's limit. A pulley change also changes heat and drive load and can require a different calibration, fuel system or cooling. Belt wrap, tension, alignment, brackets and pulley compatibility matter; belt slip or a damaged drive can make actual speed different from the calculation. Rotrex's handbook gives its own model-specific procedure and ratios; they are not universal.

Bypass and twincharging

Many positive-displacement installations have a bypass that opens at light load to reduce the pressure difference across the blower and associated losses, then closes when boost is requested. Whipple's Mustang instructions describe that function for its kit; valve control and plumbing differ by installation. A supercharger bypass is not the same device as the exhaust wastegate on a turbo.

Twincharging combines a supercharger and a turbocharger. The mechanical unit can assist response while the turbo builds its contribution; valves and sometimes a clutch coordinate the paths. Volkswagen's 1.4-litre dual-charged TSI is one production example. See the forced-induction overview for the series arrangement and the documented operating ranges.

Upgrades, supporting systems and maintenance

  • Cooling and fuel: More delivered air requires a matched fuel and ignition calibration and an assessment of knock, charge temperature and intercooling. See charge cooling and fuel system upgrades.
  • Engine and driveline: Verify that the pistons, rods, head sealing, clutch and transmission suit the intended torque and duty. A pulley or blower rating does not establish the engine's safe limit.
  • Lubrication: Follow the specific supercharger's oil, reservoir, cooling and maintenance instructions. Some have a self-contained gear case; others use an external fluid circuit. Do not substitute fluids between designs.
  • Verification: Check the drive, bypass and intake for correct operation and leaks; monitor pressure, intake temperature, fuel pressure and appropriate mixture and knock data under controlled load. Investigate unexpected noise, belt dust or rising temperature before increasing load.

Sources