Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engines
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Bosch

What the crank and cam sensors are for

A four-stroke engine needs the crank angle within one revolution, and it needs to know which of the two revolutions is under way. The crank pattern repeats every turn. The cycle takes two, so compression top dead centre and exhaust top dead centre share a crank angle.

The 2016 Bosch Mobility crankshaft sensor measures speed and position. Its Hall version can also measure direction of rotation. The control unit uses that measurement for injection and ignition timing. See common-rail diesel fuel systems and ignition systems and spark plugs. D-Jetronic timed injection from distributor contacts, which turned with the camshaft, and it had no crankshaft sensor.

Later control units read a toothed wheel on the crankshaft. A second sensor, usually on the camshaft, separates the two revolutions.

Inductive sensors

An inductive sensor is a coil and a magnet facing a toothed steel wheel. The Bosch Motorsport IS-C is a bar magnet, a soft-magnetic pole pin and a coil with two connections. A ferromagnetic tooth changes the flux, and the coil voltage follows that change. The time between zero crossings gives the speed.

The Bosch iBusiness catalogue describes the same sensors. A tooth concentrates the flux and a gap weakens it, so each edge induces an alternating voltage. Pulse size depends on speed, air gap, tooth shape and the wheel metal. Amplitude and frequency both rise with speed. At low speed the voltage is very small, and a minimum speed is required before it can be used.

For DG-6-K, part 0 261 210 128, the range is 20 to 7000 rpm. Winding resistance is 860 Ω ± 10% at 20 °C. Inductance at 1 kHz is 370 ± 60 mH. Output is 210 V at 0.3 mm and 7000 rpm, and 170 mV at 1.5 mm and 50 rpm. The table lists 7000 Hz for a 60-2 wheel.

Those voltages belong to the DG-6-K. The IS-C coil resistance is 340 Ω and its maximum inductance is 64 mH. The air gap on its drawn wheel is 0.8 ± 0.3 mm. It has no supply pin. On connector ASL 6-06-05SN-HE, pin 2 is ground, pin 3 is Sig+ and pin 5 is the screen (Scr). Pins 1 and 4 are unused. The mating connector is ASL 0-06-05PN-HE, order F 02U 000 237-01. This is the 3/8-24 UNF IS-C, order B 261 209 609-01.

Hall sensors

A Hall sensor needs a supply. The catalogue Hall speed sensors combine a Hall element, a Schmitt trigger, an open-collector output and a permanent magnet, and they are listed for crank, cam or wheel speed. The voltage the control unit evaluates does not depend on wheel speed, so the wheel can be read almost down to a stop. In that catalogue, nmin = 0 means static operation is possible.

DG-23, part 0 261 210 303, has a rated supply of 5 V, an allowed range of 4.5 to 18 V, a minimum speed of 0 rpm and a working air gap of 0.3 to 1.5 mm. The low level is a saturation voltage of 0.5 V or less.

The Mini-HA-P is a Bosch Motorsport Hall sensor for camshaft or wheel speed, facing a ferromagnetic wheel. The output is digital, active low, and an open collector for 1 kΩ. Supply is 5 to 18 V at 10 mA. The signal runs from 0.4 V to less than the supply. On ASL606-05PC-HE, order F02U.V00.564-03, pin 1 is supply, pin 2 is ground and pin 3 is the signal. On connector 1 234 482 092, order F02U.V00.566-02, pin 1 is supply, pin 2 is the signal and pin 3 is ground.

The 2016 Mobility crankshaft sensor is differential Hall, with or without direction detection, or inductive. Its Hall air gap is 0.2 to 1.8 mm, on a steel or multipole wheel. Its inductive version is described as giving a high output at low speed.

The missing-tooth wheel

Equal teeth give speed. A gap marks one place in the revolution. The Mobility crankshaft sheet says the reference is a missing element, and it labels the wheel 60-2. The catalogue calls that mark a large tooth gap, used for position as well as speed. The IS-C sheet lists 60-2 teeth.

On the MS 6 EVO the tooth count includes the missing teeth, and a second label is how many are missing. The manual starts from 60-2, also written 60 (-2). On those labels, 60-2 is 60 tooth positions with two missing. The control unit finds the gap, then takes angle from the teeth after it. The MS 3 Sport manual puts the reference on the second falling edge after the gap, and measures top dead centre from that tooth.

The same manuals give other counts. The MS 3 Sport accepts 36-2 or 60-2. The MS 6 EVO allows 30 to 60 teeth, including the missing ones, and it states that 4-1 and 6-1 wheels are not usable. Fewer teeth make the angle coarser. The count has to be read from the wheel and entered for that control unit.

The IS-C drawing and the MS 6 recommendation use a tooth depth of 3.5 mm and a gap of half that depth. The manual says that half depth matters for an inductive sensor. The IS-C is specified for a ferromagnetic wheel of that drawn size, and a different wheel has to be tested.

Why the camshaft is still required

The 60-2 gap is back in the same place after one crank turn, and the four-stroke cycle is only half done. The MS 3 Sport separates the turns with one camshaft tooth and a Hall sensor. It recommends the HA-P, part 0 232 103 037. At compression top dead centre the tooth is at the sensor. After 360 crank degrees, at exhaust top dead centre, the crank mark lines up again and the cam tooth is on the opposite side. That edge identifies the compression event, so injection and the spark are timed to that stroke.

On the MS 3 Sport the tooth produces a low Hall signal. The MS 6 EVO manual allows the same inversion, and it asks for one cam tooth at least 48 crank degrees wide (24 cam degrees). It also allows a quick-start production camshaft design. Bosch patent US 9,316,126 describes camshaft wheels with four teeth of different lengths, used for faster synchronisation and a quicker start.

The 2016 Mobility camshaft position sensor is a single-Hall product with true power on. The sheet calls that quick start: a position is available as soon as the engine starts. The air gap is 0.2 to 1.8 mm. The control unit uses the camshaft position for injection, ignition and variable camshaft phasing. Where the camshaft sits, and how it is driven, is on camshafts.

Air gap, the wheel and the cranking signal

DG-6-K states 210 V at 7000 rpm with a 0.3 mm gap, and 170 mV at 50 rpm with a 1.5 mm gap. Amplitude rises with speed, and it also depends on the gap, so the high-speed voltage can be large while the voltage at cranking speed is small. The catalogue requires a minimum speed before those low voltages can be used. DG-6-K starts at 20 rpm. DG-23 is specified from 0 rpm, and its level is not set by speed.

A wider air gap reduces the inductive pulse. The allowed gap is the one on that sensor’s sheet: 0.8 ± 0.3 mm for the IS-C and the MS 6 wheel, and the wider ranges given above for the Mobility, DG-23 and Mini-HA-P parts.

The MS 3 Sport manual requires sharp teeth on the sensor wheel. The catalogue says the ring is part of the measurement and has to be made to a high standard. The reference edge on the MS 3 Sport is the second falling edge after the gap. The IS-C names the coil wires Sig+ and ground.

Sources

Accessed 2026-11-13.

  1. Bosch Motorsport, Inductive Speed Sensor IS-C, 20 October 2016, order B 261 209 609-01. Supports the coil and magnet, the zero crossings, 340 Ω, 64 mH, the 0.8 ± 0.3 mm air gap, the 60-2 wheel, the ferromagnetic-wheel note and the IS-C connector.
  2. Bosch iBusiness sensors catalogue, Bosch Group PDF, file properties dated 16 April 2018. Supports the alternating voltage, amplitude against speed and air gap, the tooth-gap reference, DG-6-K part 0 261 210 128, and Hall sensor DG-23 part 0 261 210 303, including supply, saturation voltage and nmin = 0.
  3. Bosch Mobility, Crankshaft speed sensor, document 292000P1GQ-2015-DS, 2016. Supports Hall or inductive sensing, the missing element as the reference, the 60-2 label, the air-gap ranges, direction detection, and use of the signal for injection and ignition timing.
  4. Bosch Mobility, Camshaft position sensor, document 292000P1GR-2015-DS, 2016. Supports the single-Hall principle, true power on, position immediately after start, the 0.2 to 1.8 mm air gap, and use of camshaft position for injection, ignition and camshaft phasing.
  5. Bosch Motorsport, Speed Sensor Hall-Effect Mini-HA-P, 12 June 2026. Supports the digital Hall output, the 5 to 18 V supply, the 0.4 V to supply signal, the open-collector circuit, the air gap and the two connector pinouts.
  6. Bosch Motorsport, ECU MS 3 Sport manual, version 1.4, 16 September 2016. Supports 36-2 and 60-2 wheels, the single cam tooth, HA-P part 0 232 103 037, compression and exhaust top dead centre, the second falling edge after the gap, sharp teeth and the inverted Hall signal.
  7. Bosch Motorsport, Engine Control Unit MS 6 EVO manual, version 2.5, 23 July 2026. Supports 60 (-2), a tooth count that includes the missing teeth, the missing-tooth count, the 30 to 60 range, rejection of 4-1 and 6-1, one cam tooth or a quick-start production cam design, the low Hall level on a tooth, the 0.8 ± 0.3 mm gap and the half-depth gap for an inductive sensor.
  8. Robert Bosch GmbH, US patent 9,316,126, granted 19 April 2016. Supports the description of camshaft sensor wheels with four teeth of different lengths, used for faster synchronisation and a quicker engine start.