What the 14CUX is
The Lucas 14CUX is the last of three hot-wire fuel-injection controllers Lucas fitted to the Rover V8 in Land Rover vehicles. The Land Rover systems notes treat them as one system:
- 13CU, 1987-88
- 14CU, 1989
- 14CUX, 1990-95
All three use a 40-pin connector and control fuel only. Spark remains on a distributor. The published history says Lucas built the 13CU by revising Bosch L-Jetronic, adding the diagnostics California required, and replacing the flap meter with a hot-wire sensor. In that account the 13CU and 14CU were for the 3.5 litre V8 only. The 14CU is the more compact ECU, used on US-market Range Rovers in 1989. The 14CUX added later injectors and, in some markets, an external fault display and a tune resistor.
Land Rover fitment in that history is Discovery, Defender and Range Rover. TVR used it on the Griffith and Chimaera, including capacities up to 5.0 litres that needed their own maps. Ginetta used it on the G33 3.9 of 1990-93, and Marcos and Morgan used it as well. For 1996 Land Rover replaced it with GEMS. The same article names Bosch Motronic ML2.1 as the other successor. The earlier flap system is the 4CU.
The module is under the passenger seat on 1987-94 vehicles and behind the glovebox on 1995 vehicles. The main relay follows that move. On a Defender the relay is on the passenger side of the bulkhead.
Air, throttle and temperature
The airflow sensor holds one wire 100 °C above the other. More air needs more current to hold that difference. The systems notes give a typical idle output of 1.3-1.5 V. Fault 12 is set below 122 mV once the engine is above cranking speed, or above 4.96 V while speed is under 976 rpm for more than 160 ms.
The throttle potentiometer adds fuel during hard acceleration and cuts fuel on a closed-throttle overrun. A 13CU sensor has to be set to 290-360 mV when it is fitted. A 14CU or 14CUX adapts to an initial voltage from 80 to 500 mV and is not adjusted that way. If the sensor fails, the notes say the ECU substitutes 576 mV and lights the lamp. Fault 17 is under 78 mV for more than 160 ms.
The coolant sensor is used for cold and hot fuelling and for the closed-loop decision. Fault 14 is a signal outside 0.15-4.9 V for more than 160 ms. The ECU then substitutes 36 °C. The fuel-temperature sensor on the rail lengthens the pulse on a hot restart. From 1989 the notes also use it to run the cooling fans when the under-bonnet temperature is extreme. Fault 15, 14CUX only, is a signal outside 0.08-4.9 V for more than 160 ms, with no default value.
Lambda, speed and the injectors
A heated oxygen sensor in each downpipe lets the ECU trim the banks separately. The signals sit in a 0-1.1 V band. Faults 44 and 45 are a sensor that will not switch after a large fuel change on that bank, tested hot, with throttle voltage above 2 V and a road-speed signal present. Engine speed comes from the coil negative through a 6800 ohm dropper, about 7 V at the ECU. Without ignition pulses the injectors stay closed. Road speed tells the ECU whether the vehicle is above or below 3 mph so the idle valve can be placed as the vehicle stops. Fault 69, 14CUX only, watches the park/neutral switch.
The ECU grounds bank A on pin 13 and bank B on pin 11. The banks alternate, except during starting, when both fire together. Overrun closes them. The notes give about 2.4 ms at idle and about 9.0 ms at full load. Each injector is 16 ohms; a parallel bank reads about 4 ohms.
The idle valve has 180 steps. Position 0 is fully open and 180 is fully closed. Hot, with no extra load, the notes put it near step 160. Air conditioning, the heated screen and a shift out of park open it by a fixed number of steps. Coil resistance is 40-60 ohms cold and up to 70 ohms hot. At key-off the published description says the ECU drives the bypass fully open for the next start.
Purge is a 14CU and 14CUX output. Above 54 °C coolant, and in closed loop, the ECU pulses the valve below 1700 rpm and holds it open above that speed, then stops if the oxygen sensors show the canister is empty. The pump runs for one second at key-on and then whenever ignition pulses say the engine is turning. The inertia switch is under the left front seat until 1994 and on the engine-bay bulkhead from 1995.
Processor, tune resistor and fault codes
The published hardware description says the 14CUX uses a Motorola MC6803U4, chosen because its three timer outputs can drive the two injector banks separately. The chip carries a Lucas number, not the Motorola marking. Memory is a 27C128 or 27C256, soldered on most early PRC boards and socketed on later PRC and AMR boards. Only half of a 32 KB device is used, so the image is stored twice. Up to five fuel maps can be present. In some markets a harness resistor selects the map. North American firmware in that account ignores the resistor. The Land Rover connector list marks pin 5 as the tune resistor for 1990 only, and some North American cars have no pin there. Fault 21 is the tune-select code.
Diagnostics predate OBD-II. The published serial description is 7812.5 baud, from a 1 MHz clock divided by 128, at non-standard levels, able to read memory. Faults are kept while a battery-derived 5 V supply holds a 32-byte area, so disconnecting the battery clears them. On 1990-95 vehicles a two-digit display under the serial connector shows one code at a time, in priority order, with the ignition on. The Land Rover clear is: ignition on, unplug the serial connector for five seconds, reconnect, ignition off until the main relay drops, ignition on, and repeat until the display is blank. TestBook or the Lucas hand-held tester uses pins 9 and 18.
The 14CUX list, in the priority order of those notes, is:
| Code | Meaning in the Land Rover list |
|---|---|
| 02 | ECU supply was disconnected. Shown until the next key cycle. |
| 29 | ECU memory check. |
| 44 | Lambda sensor, bank A. |
| 45 | Lambda sensor, bank B. |
| 25 | Ignition misfire. |
| 40 | Misfire, bank A. |
| 50 | Misfire, bank B. |
| 12 | Airflow meter. |
| 21 | Tune select. |
| 34 | Injector bank A. |
| 36 | Injector bank B. |
| 14 | Coolant-temperature sensor. |
| 17 | Throttle potentiometer. |
| 18 | Throttle voltage high while airflow voltage is low. |
| 19 | Throttle voltage low while airflow voltage is high. |
| 88 | Purge valve. |
| 28 | Intake air leak. |
| 23 | Fuel supply. |
| 48 | Idle stepper. |
| 68 | Road-speed sensor. |
| 69 | Park/neutral switch. |
| 59 | Group fault: fuel supply or an air leak. |
| 15 | Fuel-temperature sensor. |
The 13CU and 14CU have a shorter list. A code from this table is not evidence that a 13CU stores it. The notes still say those earlier ECUs watch the oxygen sensors, the throttle potentiometer, the airflow meter and the coolant sensor.
Tune identities in the same notes are separate from the PRC and AMR hardware prefixes. The later cold-start calibrations they name are R3652 for the 1993-95 3.9 Range Rover Classic and Discovery, R3653 for the 1993-95 4.2 Range Rover Classic, and R3654 for the 3.9 Defender of those years. Using one of those tunes for a cold-start complaint required the rest of the cold-start package the notes specify, except on the Defender 110.
Sources
- Land Rover, 13/14CU and 14CUX Systems, the systems chapter circulated with Discovery I training material. Thresholds, pulse widths, fault codes and tune examples. Accessed 2026-11-13.
- Lucas 14CUX, Wikipedia. Processor, PROM layout, tune resistor, serial rate, applications and the GEMS successor. Accessed 2026-11-13.