How to read these tables
These are the air-flow meter plugs used on the Nissan engines named with each table, plus a Ford Cobra meter that has been fitted in front of a Z31 control unit through a level converter, and the insert used in an R35 GT-R and a Z33 350Z. Wire colours are the colours recorded with that engine. A pin marked not used was present and was not connected for the metering signal. Sensor ground and chassis ground are joined together on the early six-pin meters.
Early hot-wire meters, 2 to 7 V
CR31 RB30
| Pin | Function | Colour |
| 1 | Sensor ground | Black |
| 2 | Chassis ground | Black |
| 3 | Air-flow output, 2 to 7 V | White, shielded |
| 4 | Hot-wire cleaning, not used | Red |
| 5 | 12 V from the ECCS relay, ignition | Thick white |
| 6 | Calibration potentiometer, not used | Yellow/red |
VL RB30
| Pin | Function | Colour |
| 1 | Sensor ground | Black |
| 2 | Chassis ground | Dark brown |
| 3 | Air-flow output, 2 to 7 V | Grey/yellow, shielded |
| 4 | Hot-wire cleaning, not used | Blue |
| 5 | 12 V from the ECCS relay, ignition | Orange/black |
| 6 | Calibration potentiometer, not used | Tan |
Z31 VG30
| Pin | Function | Colour |
| A | Calibration position, not used | |
| B | Output, 2 to 7 V | Black, shielded |
| C | Chassis ground | Black |
| D | ECCS ground | Black |
| E | 12 V battery | Black, striped |
| F | Self-cleaning, not used | |
Later Nissan meters
Z32 VG30, 80 mm
| Wire | Function | Colour |
| A | Not connected | |
| B | Signal | White, shielded |
| C | 12 V ground | Black |
| D | Signal ground | Black, shielded |
| E | 12 V power | White |
| F | Not connected | |
S13 CA18 and S14 SR20, 65 mm
| Wire | Function |
| A | Not connected |
| B | 12 V power |
| C | Ground |
| D | Air-flow signal |
R32 RB20 and R33 RB25 series 1, 80 mm
| Wire | Function |
| A | Not connected |
| B | Signal |
| C | 12 V ground |
| D | Signal ground |
| E | 12 V power |
R33 series 2, R34 and WC34 RB25, 80 mm
| Colour | Function |
| White with a blue trace | Ground |
| Orange with a black trace | Signal |
| Black with a white trace | 12 V power |
Q45 VH45, 90 mm
| Wire | Colour | Function |
| 1 | White | Signal |
| 2 | Black | Ground |
| 3 | Red/white and black | 12 V power |
R35 GT-R and Z33 350Z VQ35DE insert
| Wire | Colour | Function |
| A | | No pin |
| B | Red | 12 V |
| C | Black | Ground |
| D | White | Signal |
| E | Brown | Intake-air temperature, not connected on this insert |
| F | Black | Intake-air temperature ground, not connected on this insert |
Ford Cobra meter
This pinout is the Cobra meter as used with a level converter in front of a Z31 control unit.
| Wire | Function |
| A | 12 V |
| B | Ground |
| C | Ground |
| D | Signal |
Consult diagnostic plug
The Consult port is the control-unit diagnostic connector, not the air-flow meter. Confirm the pins against the control unit before using them. Power and ground below are the ignition supply and the ground that have to be present before the data lines will answer.
S13 CA18, S14 SR20DET, HCR32 RB20, BNR32 RB20, Z32 VG30
21 is RX, 22 is TX, 31 is CLK, 32 is CHK. Ignition 12 V is on 49 and 59. Ground is on 50 and 60.
S13, S14A and S15 SR20DET, B13 SR20DE, S13 KA24DE
7 is RX, 15 is TX, 14 is CLK, 23 is CHK. Ignition 12 V is on 38 and 47. Ground is on 39 and 48.
B14 SR20DE, S14 KA24DE, N15 GA16DE
64 is RX, 65 is TX, 68 is CLK. Ignition 12 V is on 56 and 61. Ground is on 39 and 43.
ER34 and WC34 RB25DET, 1996 Z32 VG30DETT, A32 Maxima VQ30DE
75 is RX, 76 is TX, 78 is CLK on the Z32 only. Ignition 12 V is on 67 and 72. Ground is on 32.