Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Diagnostics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

A CAN transceiver is the chip between the controller and the two bus wires, or the one wire of a single-wire network. The controller speaks logic levels. The transceiver makes the dominant and recessive levels on the pair, and it is what survives a short to battery. The levels, the bit rate and the termination are on the CAN bus page. This page is the parts a board actually carries: the transceiver families, the controllers and system-basis chips beside them, and the choke, the clamp and the resistors on the same copper.

What the suffix is saying

The same silicon is sold in several moods, and the letters are the difference a replacement has to match.

MarkWhat it changes Standby or sleepA low-current mode with bus wake-up. A part with no standby, such as the TJA1050 or the plain TJA1051, stays powered with the node. VIO, /3, or a V suffixA separate logic supply so RXD and TXD match a 3.3 V, or on some newer parts a 1.8 V, microcontroller. The bus side stays on 5 V. SPLITA mid-rail bias for the two resistors of a split termination. On the TJA1040 this pin replaced the older Vref pin. Silent or receive-onlyThe driver is off and the receiver still listens. Used while a controller is learning the bit rate, so its error frames cannot hold the bus dominant. G, or a 5 Mbit/s guaranteeThe loop delay is symmetrical enough for the CAN FD data phase. A classic 1 Mbit/s part on an FD network will not keep that symmetry. SICSignal improvement. The transceiver damps the ringing of a dominant-to-recessive edge so a network with long stubs can run the data phase at 5 Mbit/s or, where the part is specified, 8 Mbit/s. Partial networkingThe transceiver itself checks a wake frame and leaves the microcontroller asleep. Specified from what was ISO 11898-6, now inside ISO 11898-2. Q1, or AEC-Q100The automotive grade. A catalog part with the same number and no Q1 is the industrial temperature and screening.

The usual 8-pin high-speed footprint, the one NXP documents for the PCA82C250, the TJA1050 and the TJA1040, is TXD, ground, VCC and RXD down one side, and the reference or SPLIT pin, CANL, CANH and the slope, silent or standby pin down the other. Later families that advertise pin compatibility keep that footprint. A fault-tolerant part and a single-wire part use a different one.

Classic high-speed, up to 1 Mbit/s

These are the transceivers on modules built before CAN FD timing was required. They speak ISO 11898-2 at up to 1 Mbit/s. NXP's own migration note treats the TJA1040 as the successor of the PCA82C250 and PCA82C251, and the TJA1050 as the same silicon idea without a standby mode.

PartMakerWhat is on the board PCA82C250NXPThe first widely fitted high-speed transceiver. Slope control on the Rs pin, standby, up to 1 Mbit/s, at least 110 nodes. Bus pins tolerate less abuse than later parts. Not for new designs. PCA82C251NXPThe 24 V sibling of the PCA82C250, with a wider bus-pin voltage. TJA1050NXPHigh-speed, no standby. Built for nodes that lose power with ignition. Much lower emissions than the PCA82C250. SPLIT pin for the termination midpoint. TJA1040NXPThe TJA1050 with standby and bus wake-up. Pin compatible with the PCA82C250, and passive on the bus when VCC is off. TJA1041, TJA1041ANXPHigh-speed with sleep, local and bus wake-up, an inhibit output and a go-to-sleep command. The part NXP's application note uses when it draws the choke and the ESD diode. TLE6251-2GInfineonHigh-speed up to 1 Mbaud, ISO 11898-5 wake-up, VIO, a SPLIT pin, receive-only mode, and a diagnosis pin for shorted bus wires and a stuck dominant. MCP2551Microchip5 V high-speed transceiver up to 1 Mbit/s, the part beside a huge number of MCP2515 boards. MCP2561, MCP2562MicrochipThe later high-speed pair. The MCP2562 brings out VIO. Standby mode. SN65HVD230, 231, 232Texas Instruments3.3 V high-speed family up to 1 Mbit/s. The 230 has slope control and standby, the 231 has a sleep pin, the 232 is the always-on version. SN65HVD251Texas Instruments5 V high-speed transceiver for 12 V and 24 V nodes. L9615STHigh-speed transceiver specified to 500 kbaud, with two slope settings. L9616STThe 1 Mbaud member of the same ST family, AEC-Q100, slope control for 1 Mbaud or 250 kbaud. MAX3051Analog Devices3.3 V, up to 1 Mbit/s, with slope control, standby and shutdown. The common-mode range is wider than ISO 11898. It is not the automotive fault-voltage part.

CAN FD, up to 2 Mbit/s and 5 Mbit/s

A CAN FD transceiver is still an ISO 11898-2 part. The extra promise is loop-delay symmetry in the data phase. NXP's CAN FD portfolio guarantees that symmetry to 5 Mbit/s. Texas Instruments splits the same idea: the plain TCAN1042 is specified to 2 Mbit/s, and the G suffix to 5 Mbit/s. Infineon states the same 5 Mbit/s ceiling on the TLE9250 and TLE9251, and says the symmetry is good enough that many boards drop the common-mode choke.

FamilyMakerWhat distinguishes it TJA1042, including B and CNXPStandby and bus wake-up, 12 V and 24 V, FD to 5 Mbit/s. B and C shorten the propagation delay for a larger network. Some variants have VIO, some have SPLIT. TJA1043NXPThe FD part with fail-safe diagnostics and a fuller power-management scheme. TJA1044, TJA1044VNXPStandby, aimed at automotive nodes. The V variant is the VIO version. TJA1049NXPStandby with bus wake-up, biased toward low emission and ESD. TJA1051NXPFD transceiver for nodes that do not need standby. /3 is VIO, /E is a low-current off mode. NXP now points new designs at the TJA1057. TJA1057NXPThe current recommendation in place of the TJA1051, in the same role. TJA1059NXPTwo high-speed transceivers in one package. UJA1161A, UJA1162A, UJA1166ANXPFD transceivers with their own 5 V CAN supply. Standby on the UJA1161A, sleep on the UJA1162A, and a 5 V output for other loads on the UJA1166A. TLE9250InfineonFD to 5 Mbit/s, no separate wake supply. The cost-optimised member of the family. TLE9251, TLE9351BInfineonFD to 5 Mbit/s with standby. The wake receiver can be supplied from VIO. The B generation is the current migration target. TLE9252, TLT9252InfineonTwo supplies, so the bus side stays up while the logic supply dips in cranking. TLT parts are the higher-temperature Endurance grades, to 150 °C ambient. TLE9254, TLE9350BInfineonThe FD family with and without VIO. TLE9350B is the later, cost-optimised generation. TCAN1042-Q1, TCAN1042V-Q1Texas InstrumentsFD, standby, bus fault to ±58 V. Plain parts to 2 Mbit/s, G parts to 5 Mbit/s. V is the I/O level shift. Fault protection and a passive unpowered bus. TCAN1044A-Q1Texas InstrumentsThe newer standby part Texas Instruments names as the upgrade from the TCAN1042. TCAN1051-Q1Texas InstrumentsSilent mode, so the node can listen without driving. Classic CAN and FD to 2 Mbit/s, and to 5 Mbit/s with the G suffix. V is the I/O supply. Bus fault is ±58 V, or ±70 V on the H variants. TCAN330, TCAN332, TCAN334, TCAN337Texas Instruments3.3 V parts to 1 Mbit/s, sharing a bus with 5 V transceivers. The G suffix on each, TCAN330G through TCAN337G, adds FD timing to 5 Mbit/s. Silent mode is on the 330 and 337, standby with wake on the 334, and the 332 is normal mode only. Bus fault protection is ±14 V. MCP2561FD, MCP2562FDMicrochipFD timing specified at 2, 5 and 8 Mbit/s, with standby. One variant has the SPLIT pin and the other has VIO from 1.8 V to 5.5 V. ATA6560, ATA6561 and the ATA656x familyMicrochipAutomotive high-speed and FD transceivers from the former Atmel line. Standby, and VIO on the variants that have it. NCV7344onsemiFD timing specified to 5 Mbit/s, standby with bus wake-up, VIO on the -3 version. Follows the NCV734x series and the earlier AMIS42665 and AMIS-30660.

Signal improvement, and partial networking

Signal-improvement parts stay inside ISO 11898-2 and add the behaviour in CiA 601-4. They are sold as pin-compatible replacements for the ordinary FD transceivers. NXP's TJA1462 replaces a TJA1042 footprint. Texas Instruments' TCAN1462-Q1 replaces a TCAN1042-Q1 or TCAN1044A-Q1 footprint. Infineon's TLE9371 replaces a TLE9251 or TLE9351 footprint. The data phase these families advertise, where the wiring allows it, is 8 Mbit/s. NXP also lists a CAN SIC XL category aimed at 20 Mbit/s. That is a separate transceiver mode, using the pulse-width signalling the CAN page already distinguishes from ordinary CAN FD.

PartMakerStatus and role TJA1462NXPSIC with standby. The drop-in for a TJA1042-class node. TJA1463NXPSIC with sleep. TJA1464, TJA1467, TJA1468NXPFurther SIC parts. NXP was listing these as preproduction, the TJA1468 as a dual channel. TJA1465, TJA1466NXPSIC with partial networking. NXP was listing these as under development. TCAN1462-Q1, TCAN1462V-Q1Texas InstrumentsSIC with standby, ±58 V bus fault, VIO down to 1.8 V on the V part. Specified for networks that want 5 Mbit/s or 8 Mbit/s with stubs. TLE9371SJ, TLE9371VSJInfineonSIC with bus wake-up. The V part has VIO. Infineon states ISO 11898-2:2024 and backwards behaviour at 1, 2 and 5 Mbit/s.

Partial networking is the selective wake-up. The transceiver watches the identifiers and, on the parts that allow it, a slice of the data field, and only then wakes the microcontroller.

PartMakerWhat it wakes on TJA1145ANXPFD partial networking to 5 Mbit/s, ISO 11898-2:2016. TLE9255W, TLT9255WInfineonSPI-configured wake identifier up to 29 bits and data up to 64 bits. Can be set to ignore a CAN FD payload so a classic controller can share the wire. Sleep current is specified under 26 µA. The TLT grade is the hotter Endurance part. TCAN1145-Q1Texas InstrumentsAutomotive FD partial-networking transceiver. Texas Instruments publishes an evaluation board for it. UJA1169NXPA system-basis chip whose transceiver can be CAN FD-passive and still do selective wake-up, so the microcontroller need not understand FD frames while it is asleep.

Secure, isolated, fault-tolerant, single-wire

The TJA1152 is NXP's secure high-speed transceiver. It behaves as a normal FD transceiver until it sees a frame its configuration does not allow: a spoofed identifier, a flooded bus, or a tampered message. It then contains that traffic without a cryptographic stack in the microcontroller. The TJA1152A has VIO. The arbitration rate is 125, 250 or 500 kbit/s, and the data phase is two or four times that.

Isolated transceivers put the barrier in the same package as the driver. They are the parts on a battery-management board, a 48 V rail, or a charger, where the bus ground is not the logic ground.

PartMakerIsolation and rate TJA1052i, grades /1, /2 and /5NXPCapacitive isolation, FD to 5 Mbit/s. The three grades are the three isolation voltages in the SO16. Aimed at electric and hybrid vehicles. ISO1042, ISO1042-Q1Texas InstrumentsIsolated FD. Classic CAN to 1 Mbit/s and FD to 5 Mbit/s, 5 kV RMS, bus fault ±70 V, logic supply from 1.8 V to 5 V. ISO1044Texas InstrumentsThe smaller isolated FD part, 5 Mbit/s, 3 kV RMS, bus fault ±58 V. ISOW1050Texas InstrumentsIsolated transceiver to 5 Mbit/s with the isolated supply in the same package, 5 kV RMS, bus fault ±58 V. ADM3050EAnalog DevicesIsolated FD with iCoupler and an on-chip isolated supply. About 5 kV RMS, ±40 V bus pins, ±25 V common mode. ADM3055E, ADM3057EAnalog DevicesThe same isolation idea with standby, and a silent mode that lets a controller hunt the bit rate without driving error frames. ADM3056EAnalog DevicesIsolated FD with the low-power mode and without the integrated power of the ADM3055E.

Fault-tolerant transceivers are ISO 11898-3, 125 kbit/s, and they are a different pinout and a different voltage. The TJA1054 and the later TJA1055 drive a differential pair and, if one wire shorts, carry on with the surviving wire. The TJA1055 is NXP's enhanced TJA1054: lower sleep current, better ESD, and wake-up indicated even when VCC is down. The TJA1054 itself replaced the PCA82C252 and the TJA1053. Up to 32 nodes. Putting a high-speed 120 ohm transceiver on this network, or the other way round, does not make a working bus.

Single-wire transceivers are SAE J2411, one wire and ground, normal traffic near 33.3 kbit/s and a high-speed download near 83.3 kbit/s while a service tool holds the extra load. The high-speed mode is for that download. It is not the rate of the body bus in ordinary driving.

PartMakerNotes NCV7356onsemiJ2411 and GMW3089. Supply 5 V to 27 V. Normal rate typically 33 kbit/s, high-speed typically 83 kbit/s, with the part capable of 40 kbit/s and 100 kbit/s. SO8 and SO14. Sleep under 60 µA. TH8056MelexisGMW3089 and J2411. The same two rates. SO8 and a thermally enhanced SO14 with an inhibit pin for an external regulator. AU5790NXPThe earlier Philips single-wire part. 33.3 kbit/s with 32 nodes, 83 kbit/s high-speed mode, waveshaping, load-dump protection. The SO8 shares the later single-wire pinout. MC33897NXPThe Freescale single-wire transceiver, sold in the 14-pin package. TLE6255InfineonThe earlier single-wire transceiver, 14-pin. Hardware notes now list it as obsolete, with the NCV7356 and the TH8056 in the same role.

Controllers and system-basis chips

The transceiver is not the protocol. These are the chips that hand it TXD and RXD, or that hide both behind SPI.

PartMakerRole SJA1000NXPThe standalone classic CAN controller of the 1990s and 2000s. Parallel bus, acceptance filter with its own mask polarity. Still the core inside a lot of older interface hardware. MCP2515MicrochipSPI classic CAN controller, almost always paired with an MCP2551 or MCP2562. MCP2517FD, MCP2518FDMicrochipSPI CAN FD controllers. The MCP2518FD is the later one. MCP25625MicrochipMCP2515 controller and a transceiver in one package. TCAN4550Texas InstrumentsBosch M_CAN and a FD transceiver behind SPI. The product page states bus rates up to 5 Mbit/s, with standby, sleep and wake from the bus or a local pin. The way a processor with no CAN peripheral still sits on the pair. UJA1169NXPMini system-basis chip: FD transceiver, 5 V or 3.3 V regulator at 250 mA, watchdog, SPI, and partial networking on the variants that have it. Six supply combinations. TLE926x, TLE927x, TLE9461, TLE9471InfineonOPTIREG system-basis chips. The CAN transceiver is one block inside a regulator, watchdog and wake-up device.

The parts on the same copper

NXP's application notes for the TJA1050 and the TJA1041 draw the same network between the transceiver and the connector, and it is what a repair turns up there.

Termination is two 60 ohm resistors in series across CANH and CANL, or one 120 ohm, at each end of the bus and nowhere else. The midpoint of the split pair can go to the SPLIT pin through a capacitor. A third 120 ohm, added because a drawing showed one, is the fault the CAN page already warns about.

The clamp is a low-capacitance dual diode at the connector. NXP specifies the PESD1CAN, about 11 pF, for this job, and an ECU with both that diode and a choke was measured above 20 kV. onsemi's NUP2105L is the dual TVS its CAN protection note puts in the same position. The diode sits at the connector. The choke sits at the transceiver.

The choke is a common-mode part. NXP asks for stray inductance under 500 nH, which is what a bifilar winding gives, and names the B82789-C104 as the example. A choke with more leakage rings against the pin capacitance and can make RXD toggle twice on one edge. Texas Instruments measured that ringing on a set of production chokes. The values that show up on CAN boards are 51 µH and 100 µH.

ChokeMakerWhere it is specified B82789-C104EPCOS100 µH. The part NXP draws next to the TJA1050. B82789C0223, B82789C0513EPCOS22 µH and 51 µH. Both are in the set Texas Instruments measured. B82799C0474EPCOS470 µH. Included in that same measurement set. A larger inductance is not automatically a better CAN choke. ACT45B-510-2P, ACT45B-101-2PTDK51 µH and 100 µH. In the Texas Instruments measurement set. ACT1210-101-2PTDK100 µH in the 1210 size. B82787C0104EPCOS100 µH, the EPCOS part in the same distributor lists as the ACT45B. DLW43SH510, DLW43SH101Murata51 µH and 100 µH. The 100 µH part is also listed at 100 mA. DLW32SH101Murata100 µH, the 1210 size those lists mark for CAN FD. PE-1210ACC101Pulse100 µH in 1210.

A newer FD transceiver is often specified to pass the vehicle EMC test with no choke at all. Fitting one anyway is a system choice. Fitting a large toroid because it is also 100 µH is the choice Texas Instruments' measurements argue against: the leakage, not the common-mode inductance, is what rings.

Sources

CAN FD portfolio. NXP. TJA1042, TJA1043, TJA1044, TJA1049, TJA1051, TJA1052i, TJA1057, TJA1059, TJA1145A and the UJA116x. Accessed 2026-11-12. CAN SIC portfolio. NXP. TJA1462, TJA1463 and the later TJA146x, including which were preproduction. Accessed 2026-11-12. TJA1042. NXP. 5 Mbit/s FD timing, VIO, SPLIT, and the B and C delay grades. Accessed 2026-11-12. Upgrading from the PCA82C250 and PCA82C251. NXP. TJA1040 and TJA1050 as the successors, with the supply, standby and bus-pin limits. Accessed 2026-11-12. TJA1055. NXP. Fault-tolerant transceiver, 125 kbit/s, single-wire fallback. Accessed 2026-11-12. TJA1152. NXP. Secure FD transceiver, allowed arbitration rates and data-phase ratios. Accessed 2026-11-12. TJA1052i. NXP. Isolated FD transceiver to 5 Mbit/s. Accessed 2026-11-12. UJA1169. NXP. System-basis chip, regulator current, and CAN FD-passive selective wake-up. Accessed 2026-11-12. TJA1050 application note. NXP. Choke, split termination, PESD1CAN, and the 500 nH stray-inductance limit. Accessed 2026-11-12. Automotive CAN transceivers. Infineon. TLE9350B, TLE9351B, TLE9255W, TLT grades and the TLE9371 SIC family. Accessed 2026-11-12. TCAN1042V-Q1. Texas Instruments. 2 Mbit/s and 5 Mbit/s grades, ±58 V, VIO. Accessed 2026-11-12. TCAN4550. Texas Instruments. SPI CAN FD controller with an integrated transceiver. Accessed 2026-11-12. ISO1042. Texas Instruments. Isolated FD, 5 Mbit/s, 5 kV RMS, ±70 V bus fault. Accessed 2026-11-12. ISO1044. Texas Instruments. Isolated FD transceiver, 5 Mbit/s, 3 kV RMS. Accessed 2026-11-12. ISOW1050. Texas Instruments. Isolated transceiver to 5 Mbit/s with an on-chip isolated supply. Accessed 2026-11-12. TCAN330 family. Texas Instruments. 3.3 V transceivers, 1 Mbit/s, and 5 Mbit/s on the G suffix. Accessed 2026-11-12. TCAN1051-Q1. Texas Instruments. Silent mode, 2 Mbit/s, 5 Mbit/s on the G suffix. Accessed 2026-11-12. MCP2561FD and MCP2562FD. Microchip. FD timing at 2, 5 and 8 Mbit/s, SPLIT and VIO. Accessed 2026-11-12. Common-mode chokes in CAN networks. Texas Instruments. Measured chokes, including ACT45B, B82789 and DLW43SH. Accessed 2026-11-12. NCV7344. onsemi. FD to 5 Mbit/s, and the earlier AMIS42665 generation. Accessed 2026-11-12. NCV7356. onsemi. Single-wire CAN, 33 kbit/s and 83 kbit/s. Accessed 2026-11-12. TH8056. Melexis. Single-wire CAN to GMW3089 and J2411. Accessed 2026-11-12. AU5790. NXP. Single-wire transceiver, 33.3 kbit/s and 83 kbit/s. Accessed 2026-11-12. Single-wire CAN breakout. Beyondlogic. The shared SO8 pinout, and the MC33897 and TLE6255 as the 14-pin parts. Accessed 2026-11-12. SN65HVD230. Texas Instruments. 3.3 V high-speed transceiver. Accessed 2026-11-12. L9616. ST. High-speed transceiver to 1 Mbaud. Accessed 2026-11-12. MAX3051. Analog Devices. 3.3 V transceiver to 1 Mbit/s. Accessed 2026-11-12. MCP2562. Microchip. High-speed transceiver with standby and VIO. Accessed 2026-11-12. Galvanically isolated CAN FD. CAN in Automation, 2019. ADM3050E, ADM3055E, ADM3056E and ADM3057E. Accessed 2026-11-12.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: CAN transceivers and the parts around them

A CAN transceiver is the chip between the controller and the two bus wires, or the one wire of a single-wire network. The controller speaks logic levels. The transceiver makes the dominant and recessive levels on the pair, and it is what survives a short to battery. The levels, the bit rate and the termination are on the CAN bus page. This page is the parts a board actually carries: the transceiver families, the controllers and system-basis chips beside them, and the choke, the clamp and the resistors on the same copper.

What the suffix is saying

The same silicon is sold in several moods, and the letters are the difference a replacement has to match.

MarkWhat it changes
Standby or sleepA low-current mode with bus wake-up. A part with no standby, such as the TJA1050 or the plain TJA1051, stays powered with the node.
VIO, /3, or a V suffixA separate logic supply so RXD and TXD match a 3.3 V, or on some newer parts a 1.8 V, microcontroller. The bus side stays on 5 V.
SPLITA mid-rail bias for the two resistors of a split termination. On the TJA1040 this pin replaced the older Vref pin.
Silent or receive-onlyThe driver is off and the receiver still listens. Used while a controller is learning the bit rate, so its error frames cannot hold the bus dominant.
G, or a 5 Mbit/s guaranteeThe loop delay is symmetrical enough for the CAN FD data phase. A classic 1 Mbit/s part on an FD network will not keep that symmetry.
SICSignal improvement. The transceiver damps the ringing of a dominant-to-recessive edge so a network with long stubs can run the data phase at 5 Mbit/s or, where the part is specified, 8 Mbit/s.
Partial networkingThe transceiver itself checks a wake frame and leaves the microcontroller asleep. Specified from what was ISO 11898-6, now inside ISO 11898-2.
Q1, or AEC-Q100The automotive grade. A catalog part with the same number and no Q1 is the industrial temperature and screening.

The usual 8-pin high-speed footprint, the one NXP documents for the PCA82C250, the TJA1050 and the TJA1040, is TXD, ground, VCC and RXD down one side, and the reference or SPLIT pin, CANL, CANH and the slope, silent or standby pin down the other. Later families that advertise pin compatibility keep that footprint. A fault-tolerant part and a single-wire part use a different one.

Classic high-speed, up to 1 Mbit/s

These are the transceivers on modules built before CAN FD timing was required. They speak ISO 11898-2 at up to 1 Mbit/s. NXP's own migration note treats the TJA1040 as the successor of the PCA82C250 and PCA82C251, and the TJA1050 as the same silicon idea without a standby mode.

PartMakerWhat is on the board
PCA82C250NXPThe first widely fitted high-speed transceiver. Slope control on the Rs pin, standby, up to 1 Mbit/s, at least 110 nodes. Bus pins tolerate less abuse than later parts. Not for new designs.
PCA82C251NXPThe 24 V sibling of the PCA82C250, with a wider bus-pin voltage.
TJA1050NXPHigh-speed, no standby. Built for nodes that lose power with ignition. Much lower emissions than the PCA82C250. SPLIT pin for the termination midpoint.
TJA1040NXPThe TJA1050 with standby and bus wake-up. Pin compatible with the PCA82C250, and passive on the bus when VCC is off.
TJA1041, TJA1041ANXPHigh-speed with sleep, local and bus wake-up, an inhibit output and a go-to-sleep command. The part NXP's application note uses when it draws the choke and the ESD diode.
TLE6251-2GInfineonHigh-speed up to 1 Mbaud, ISO 11898-5 wake-up, VIO, a SPLIT pin, receive-only mode, and a diagnosis pin for shorted bus wires and a stuck dominant.
MCP2551Microchip5 V high-speed transceiver up to 1 Mbit/s, the part beside a huge number of MCP2515 boards.
MCP2561, MCP2562MicrochipThe later high-speed pair. The MCP2562 brings out VIO. Standby mode.
SN65HVD230, 231, 232Texas Instruments3.3 V high-speed family up to 1 Mbit/s. The 230 has slope control and standby, the 231 has a sleep pin, the 232 is the always-on version.
SN65HVD251Texas Instruments5 V high-speed transceiver for 12 V and 24 V nodes.
L9615STHigh-speed transceiver specified to 500 kbaud, with two slope settings.
L9616STThe 1 Mbaud member of the same ST family, AEC-Q100, slope control for 1 Mbaud or 250 kbaud.
MAX3051Analog Devices3.3 V, up to 1 Mbit/s, with slope control, standby and shutdown. The common-mode range is wider than ISO 11898. It is not the automotive fault-voltage part.

CAN FD, up to 2 Mbit/s and 5 Mbit/s

A CAN FD transceiver is still an ISO 11898-2 part. The extra promise is loop-delay symmetry in the data phase. NXP's CAN FD portfolio guarantees that symmetry to 5 Mbit/s. Texas Instruments splits the same idea: the plain TCAN1042 is specified to 2 Mbit/s, and the G suffix to 5 Mbit/s. Infineon states the same 5 Mbit/s ceiling on the TLE9250 and TLE9251, and says the symmetry is good enough that many boards drop the common-mode choke.

FamilyMakerWhat distinguishes it
TJA1042, including B and CNXPStandby and bus wake-up, 12 V and 24 V, FD to 5 Mbit/s. B and C shorten the propagation delay for a larger network. Some variants have VIO, some have SPLIT.
TJA1043NXPThe FD part with fail-safe diagnostics and a fuller power-management scheme.
TJA1044, TJA1044VNXPStandby, aimed at automotive nodes. The V variant is the VIO version.
TJA1049NXPStandby with bus wake-up, biased toward low emission and ESD.
TJA1051NXPFD transceiver for nodes that do not need standby. /3 is VIO, /E is a low-current off mode. NXP now points new designs at the TJA1057.
TJA1057NXPThe current recommendation in place of the TJA1051, in the same role.
TJA1059NXPTwo high-speed transceivers in one package.
UJA1161A, UJA1162A, UJA1166ANXPFD transceivers with their own 5 V CAN supply. Standby on the UJA1161A, sleep on the UJA1162A, and a 5 V output for other loads on the UJA1166A.
TLE9250InfineonFD to 5 Mbit/s, no separate wake supply. The cost-optimised member of the family.
TLE9251, TLE9351BInfineonFD to 5 Mbit/s with standby. The wake receiver can be supplied from VIO. The B generation is the current migration target.
TLE9252, TLT9252InfineonTwo supplies, so the bus side stays up while the logic supply dips in cranking. TLT parts are the higher-temperature Endurance grades, to 150 °C ambient.
TLE9254, TLE9350BInfineonThe FD family with and without VIO. TLE9350B is the later, cost-optimised generation.
TCAN1042-Q1, TCAN1042V-Q1Texas InstrumentsFD, standby, bus fault to ±58 V. Plain parts to 2 Mbit/s, G parts to 5 Mbit/s. V is the I/O level shift. Fault protection and a passive unpowered bus.
TCAN1044A-Q1Texas InstrumentsThe newer standby part Texas Instruments names as the upgrade from the TCAN1042.
TCAN1051-Q1Texas InstrumentsSilent mode, so the node can listen without driving. Classic CAN and FD to 2 Mbit/s, and to 5 Mbit/s with the G suffix. V is the I/O supply. Bus fault is ±58 V, or ±70 V on the H variants.
TCAN330, TCAN332, TCAN334, TCAN337Texas Instruments3.3 V parts to 1 Mbit/s, sharing a bus with 5 V transceivers. The G suffix on each, TCAN330G through TCAN337G, adds FD timing to 5 Mbit/s. Silent mode is on the 330 and 337, standby with wake on the 334, and the 332 is normal mode only. Bus fault protection is ±14 V.
MCP2561FD, MCP2562FDMicrochipFD timing specified at 2, 5 and 8 Mbit/s, with standby. One variant has the SPLIT pin and the other has VIO from 1.8 V to 5.5 V.
ATA6560, ATA6561 and the ATA656x familyMicrochipAutomotive high-speed and FD transceivers from the former Atmel line. Standby, and VIO on the variants that have it.
NCV7344onsemiFD timing specified to 5 Mbit/s, standby with bus wake-up, VIO on the -3 version. Follows the NCV734x series and the earlier AMIS42665 and AMIS-30660.

Signal improvement, and partial networking

Signal-improvement parts stay inside ISO 11898-2 and add the behaviour in CiA 601-4. They are sold as pin-compatible replacements for the ordinary FD transceivers. NXP's TJA1462 replaces a TJA1042 footprint. Texas Instruments' TCAN1462-Q1 replaces a TCAN1042-Q1 or TCAN1044A-Q1 footprint. Infineon's TLE9371 replaces a TLE9251 or TLE9351 footprint. The data phase these families advertise, where the wiring allows it, is 8 Mbit/s. NXP also lists a CAN SIC XL category aimed at 20 Mbit/s. That is a separate transceiver mode, using the pulse-width signalling the CAN page already distinguishes from ordinary CAN FD.

PartMakerStatus and role
TJA1462NXPSIC with standby. The drop-in for a TJA1042-class node.
TJA1463NXPSIC with sleep.
TJA1464, TJA1467, TJA1468NXPFurther SIC parts. NXP was listing these as preproduction, the TJA1468 as a dual channel.
TJA1465, TJA1466NXPSIC with partial networking. NXP was listing these as under development.
TCAN1462-Q1, TCAN1462V-Q1Texas InstrumentsSIC with standby, ±58 V bus fault, VIO down to 1.8 V on the V part. Specified for networks that want 5 Mbit/s or 8 Mbit/s with stubs.
TLE9371SJ, TLE9371VSJInfineonSIC with bus wake-up. The V part has VIO. Infineon states ISO 11898-2:2024 and backwards behaviour at 1, 2 and 5 Mbit/s.

Partial networking is the selective wake-up. The transceiver watches the identifiers and, on the parts that allow it, a slice of the data field, and only then wakes the microcontroller.

PartMakerWhat it wakes on
TJA1145ANXPFD partial networking to 5 Mbit/s, ISO 11898-2:2016.
TLE9255W, TLT9255WInfineonSPI-configured wake identifier up to 29 bits and data up to 64 bits. Can be set to ignore a CAN FD payload so a classic controller can share the wire. Sleep current is specified under 26 µA. The TLT grade is the hotter Endurance part.
TCAN1145-Q1Texas InstrumentsAutomotive FD partial-networking transceiver. Texas Instruments publishes an evaluation board for it.
UJA1169NXPA system-basis chip whose transceiver can be CAN FD-passive and still do selective wake-up, so the microcontroller need not understand FD frames while it is asleep.

Secure, isolated, fault-tolerant, single-wire

The TJA1152 is NXP's secure high-speed transceiver. It behaves as a normal FD transceiver until it sees a frame its configuration does not allow: a spoofed identifier, a flooded bus, or a tampered message. It then contains that traffic without a cryptographic stack in the microcontroller. The TJA1152A has VIO. The arbitration rate is 125, 250 or 500 kbit/s, and the data phase is two or four times that.

Isolated transceivers put the barrier in the same package as the driver. They are the parts on a battery-management board, a 48 V rail, or a charger, where the bus ground is not the logic ground.

PartMakerIsolation and rate
TJA1052i, grades /1, /2 and /5NXPCapacitive isolation, FD to 5 Mbit/s. The three grades are the three isolation voltages in the SO16. Aimed at electric and hybrid vehicles.
ISO1042, ISO1042-Q1Texas InstrumentsIsolated FD. Classic CAN to 1 Mbit/s and FD to 5 Mbit/s, 5 kV RMS, bus fault ±70 V, logic supply from 1.8 V to 5 V.
ISO1044Texas InstrumentsThe smaller isolated FD part, 5 Mbit/s, 3 kV RMS, bus fault ±58 V.
ISOW1050Texas InstrumentsIsolated transceiver to 5 Mbit/s with the isolated supply in the same package, 5 kV RMS, bus fault ±58 V.
ADM3050EAnalog DevicesIsolated FD with iCoupler and an on-chip isolated supply. About 5 kV RMS, ±40 V bus pins, ±25 V common mode.
ADM3055E, ADM3057EAnalog DevicesThe same isolation idea with standby, and a silent mode that lets a controller hunt the bit rate without driving error frames.
ADM3056EAnalog DevicesIsolated FD with the low-power mode and without the integrated power of the ADM3055E.

Fault-tolerant transceivers are ISO 11898-3, 125 kbit/s, and they are a different pinout and a different voltage. The TJA1054 and the later TJA1055 drive a differential pair and, if one wire shorts, carry on with the surviving wire. The TJA1055 is NXP's enhanced TJA1054: lower sleep current, better ESD, and wake-up indicated even when VCC is down. The TJA1054 itself replaced the PCA82C252 and the TJA1053. Up to 32 nodes. Putting a high-speed 120 ohm transceiver on this network, or the other way round, does not make a working bus.

Single-wire transceivers are SAE J2411, one wire and ground, normal traffic near 33.3 kbit/s and a high-speed download near 83.3 kbit/s while a service tool holds the extra load. The high-speed mode is for that download. It is not the rate of the body bus in ordinary driving.

PartMakerNotes
NCV7356onsemiJ2411 and GMW3089. Supply 5 V to 27 V. Normal rate typically 33 kbit/s, high-speed typically 83 kbit/s, with the part capable of 40 kbit/s and 100 kbit/s. SO8 and SO14. Sleep under 60 µA.
TH8056MelexisGMW3089 and J2411. The same two rates. SO8 and a thermally enhanced SO14 with an inhibit pin for an external regulator.
AU5790NXPThe earlier Philips single-wire part. 33.3 kbit/s with 32 nodes, 83 kbit/s high-speed mode, waveshaping, load-dump protection. The SO8 shares the later single-wire pinout.
MC33897NXPThe Freescale single-wire transceiver, sold in the 14-pin package.
TLE6255InfineonThe earlier single-wire transceiver, 14-pin. Hardware notes now list it as obsolete, with the NCV7356 and the TH8056 in the same role.

Controllers and system-basis chips

The transceiver is not the protocol. These are the chips that hand it TXD and RXD, or that hide both behind SPI.

PartMakerRole
SJA1000NXPThe standalone classic CAN controller of the 1990s and 2000s. Parallel bus, acceptance filter with its own mask polarity. Still the core inside a lot of older interface hardware.
MCP2515MicrochipSPI classic CAN controller, almost always paired with an MCP2551 or MCP2562.
MCP2517FD, MCP2518FDMicrochipSPI CAN FD controllers. The MCP2518FD is the later one.
MCP25625MicrochipMCP2515 controller and a transceiver in one package.
TCAN4550Texas InstrumentsBosch M_CAN and a FD transceiver behind SPI. The product page states bus rates up to 5 Mbit/s, with standby, sleep and wake from the bus or a local pin. The way a processor with no CAN peripheral still sits on the pair.
UJA1169NXPMini system-basis chip: FD transceiver, 5 V or 3.3 V regulator at 250 mA, watchdog, SPI, and partial networking on the variants that have it. Six supply combinations.
TLE926x, TLE927x, TLE9461, TLE9471InfineonOPTIREG system-basis chips. The CAN transceiver is one block inside a regulator, watchdog and wake-up device.

The parts on the same copper

NXP's application notes for the TJA1050 and the TJA1041 draw the same network between the transceiver and the connector, and it is what a repair turns up there.

Termination is two 60 ohm resistors in series across CANH and CANL, or one 120 ohm, at each end of the bus and nowhere else. The midpoint of the split pair can go to the SPLIT pin through a capacitor. A third 120 ohm, added because a drawing showed one, is the fault the CAN page already warns about.

The clamp is a low-capacitance dual diode at the connector. NXP specifies the PESD1CAN, about 11 pF, for this job, and an ECU with both that diode and a choke was measured above 20 kV. onsemi's NUP2105L is the dual TVS its CAN protection note puts in the same position. The diode sits at the connector. The choke sits at the transceiver.

The choke is a common-mode part. NXP asks for stray inductance under 500 nH, which is what a bifilar winding gives, and names the B82789-C104 as the example. A choke with more leakage rings against the pin capacitance and can make RXD toggle twice on one edge. Texas Instruments measured that ringing on a set of production chokes. The values that show up on CAN boards are 51 µH and 100 µH.

ChokeMakerWhere it is specified
B82789-C104EPCOS100 µH. The part NXP draws next to the TJA1050.
B82789C0223, B82789C0513EPCOS22 µH and 51 µH. Both are in the set Texas Instruments measured.
B82799C0474EPCOS470 µH. Included in that same measurement set. A larger inductance is not automatically a better CAN choke.
ACT45B-510-2P, ACT45B-101-2PTDK51 µH and 100 µH. In the Texas Instruments measurement set.
ACT1210-101-2PTDK100 µH in the 1210 size.
B82787C0104EPCOS100 µH, the EPCOS part in the same distributor lists as the ACT45B.
DLW43SH510, DLW43SH101Murata51 µH and 100 µH. The 100 µH part is also listed at 100 mA.
DLW32SH101Murata100 µH, the 1210 size those lists mark for CAN FD.
PE-1210ACC101Pulse100 µH in 1210.

A newer FD transceiver is often specified to pass the vehicle EMC test with no choke at all. Fitting one anyway is a system choice. Fitting a large toroid because it is also 100 µH is the choice Texas Instruments' measurements argue against: the leakage, not the common-mode inductance, is what rings.

Sources

  • CAN FD portfolio. NXP. TJA1042, TJA1043, TJA1044, TJA1049, TJA1051, TJA1052i, TJA1057, TJA1059, TJA1145A and the UJA116x. Accessed 2026-11-12.
  • CAN SIC portfolio. NXP. TJA1462, TJA1463 and the later TJA146x, including which were preproduction. Accessed 2026-11-12.
  • TJA1042. NXP. 5 Mbit/s FD timing, VIO, SPLIT, and the B and C delay grades. Accessed 2026-11-12.
  • Upgrading from the PCA82C250 and PCA82C251. NXP. TJA1040 and TJA1050 as the successors, with the supply, standby and bus-pin limits. Accessed 2026-11-12.
  • TJA1055. NXP. Fault-tolerant transceiver, 125 kbit/s, single-wire fallback. Accessed 2026-11-12.
  • TJA1152. NXP. Secure FD transceiver, allowed arbitration rates and data-phase ratios. Accessed 2026-11-12.
  • TJA1052i. NXP. Isolated FD transceiver to 5 Mbit/s. Accessed 2026-11-12.
  • UJA1169. NXP. System-basis chip, regulator current, and CAN FD-passive selective wake-up. Accessed 2026-11-12.
  • TJA1050 application note. NXP. Choke, split termination, PESD1CAN, and the 500 nH stray-inductance limit. Accessed 2026-11-12.
  • Automotive CAN transceivers. Infineon. TLE9350B, TLE9351B, TLE9255W, TLT grades and the TLE9371 SIC family. Accessed 2026-11-12.
  • TCAN1042V-Q1. Texas Instruments. 2 Mbit/s and 5 Mbit/s grades, ±58 V, VIO. Accessed 2026-11-12.
  • TCAN4550. Texas Instruments. SPI CAN FD controller with an integrated transceiver. Accessed 2026-11-12.
  • ISO1042. Texas Instruments. Isolated FD, 5 Mbit/s, 5 kV RMS, ±70 V bus fault. Accessed 2026-11-12.
  • ISO1044. Texas Instruments. Isolated FD transceiver, 5 Mbit/s, 3 kV RMS. Accessed 2026-11-12.
  • ISOW1050. Texas Instruments. Isolated transceiver to 5 Mbit/s with an on-chip isolated supply. Accessed 2026-11-12.
  • TCAN330 family. Texas Instruments. 3.3 V transceivers, 1 Mbit/s, and 5 Mbit/s on the G suffix. Accessed 2026-11-12.
  • TCAN1051-Q1. Texas Instruments. Silent mode, 2 Mbit/s, 5 Mbit/s on the G suffix. Accessed 2026-11-12.
  • MCP2561FD and MCP2562FD. Microchip. FD timing at 2, 5 and 8 Mbit/s, SPLIT and VIO. Accessed 2026-11-12.
  • Common-mode chokes in CAN networks. Texas Instruments. Measured chokes, including ACT45B, B82789 and DLW43SH. Accessed 2026-11-12.
  • NCV7344. onsemi. FD to 5 Mbit/s, and the earlier AMIS42665 generation. Accessed 2026-11-12.
  • NCV7356. onsemi. Single-wire CAN, 33 kbit/s and 83 kbit/s. Accessed 2026-11-12.
  • TH8056. Melexis. Single-wire CAN to GMW3089 and J2411. Accessed 2026-11-12.
  • AU5790. NXP. Single-wire transceiver, 33.3 kbit/s and 83 kbit/s. Accessed 2026-11-12.
  • Single-wire CAN breakout. Beyondlogic. The shared SO8 pinout, and the MC33897 and TLE6255 as the 14-pin parts. Accessed 2026-11-12.
  • SN65HVD230. Texas Instruments. 3.3 V high-speed transceiver. Accessed 2026-11-12.
  • L9616. ST. High-speed transceiver to 1 Mbaud. Accessed 2026-11-12.
  • MAX3051. Analog Devices. 3.3 V transceiver to 1 Mbit/s. Accessed 2026-11-12.
  • MCP2562. Microchip. High-speed transceiver with standby and VIO. Accessed 2026-11-12.
  • Galvanically isolated CAN FD. CAN in Automation, 2019. ADM3050E, ADM3055E, ADM3056E and ADM3057E. Accessed 2026-11-12.
Revision 1: CAN transceivers and the parts around them

A CAN transceiver is the chip between the controller and the two bus wires, or the one wire of a single-wire network. The controller speaks logic levels. The transceiver makes the dominant and recessive levels on the pair, and it is what survives a short to battery. The levels, the bit rate and the termination are on the CAN bus page. This page is the parts a board actually carries: the transceiver families, the controllers and system-basis chips beside them, and the choke, the clamp and the resistors on the same copper.

What the suffix is saying

The same silicon is sold in several moods, and the letters are the difference a replacement has to match.

MarkWhat it changes
Standby or sleepA low-current mode with bus wake-up. A part with no standby, such as the TJA1050 or the plain TJA1051, stays powered with the node.
VIO, /3, or a V suffixA separate logic supply so RXD and TXD match a 3.3 V, or on some newer parts a 1.8 V, microcontroller. The bus side stays on 5 V.
SPLITA mid-rail bias for the two resistors of a split termination. On the TJA1040 this pin replaced the older Vref pin.
Silent or receive-onlyThe driver is off and the receiver still listens. Used while a controller is learning the bit rate, so its error frames cannot hold the bus dominant.
G, or a 5 Mbit/s guaranteeThe loop delay is symmetrical enough for the CAN FD data phase. A classic 1 Mbit/s part on an FD network will not keep that symmetry.
SICSignal improvement. The transceiver damps the ringing of a dominant-to-recessive edge so a network with long stubs can run the data phase at 5 Mbit/s or, where the part is specified, 8 Mbit/s.
Partial networkingThe transceiver itself checks a wake frame and leaves the microcontroller asleep. Specified from what was ISO 11898-6, now inside ISO 11898-2.
Q1, or AEC-Q100The automotive grade. A catalog part with the same number and no Q1 is the industrial temperature and screening.

The usual 8-pin high-speed footprint, the one NXP documents for the PCA82C250, the TJA1050 and the TJA1040, is TXD, ground, VCC and RXD down one side, and the reference or SPLIT pin, CANL, CANH and the slope, silent or standby pin down the other. Later families that advertise pin compatibility keep that footprint. A fault-tolerant part and a single-wire part use a different one.

Classic high-speed, up to 1 Mbit/s

These are the transceivers on modules built before CAN FD timing was required. They speak ISO 11898-2 at up to 1 Mbit/s. NXP's own migration note treats the TJA1040 as the successor of the PCA82C250 and PCA82C251, and the TJA1050 as the same silicon idea without a standby mode.

PartMakerWhat is on the board
PCA82C250NXPThe first widely fitted high-speed transceiver. Slope control on the Rs pin, standby, up to 1 Mbit/s, at least 110 nodes. Bus pins tolerate less abuse than later parts. Not for new designs.
PCA82C251NXPThe 24 V sibling of the PCA82C250, with a wider bus-pin voltage.
TJA1050NXPHigh-speed, no standby. Built for nodes that lose power with ignition. Much lower emissions than the PCA82C250. SPLIT pin for the termination midpoint.
TJA1040NXPThe TJA1050 with standby and bus wake-up. Pin compatible with the PCA82C250, and passive on the bus when VCC is off.
TJA1041, TJA1041ANXPHigh-speed with sleep, local and bus wake-up, an inhibit output and a go-to-sleep command. The part NXP's application note uses when it draws the choke and the ESD diode.
TLE6251-2GInfineonHigh-speed up to 1 Mbaud, ISO 11898-5 wake-up, VIO, a SPLIT pin, receive-only mode, and a diagnosis pin for shorted bus wires and a stuck dominant.
MCP2551Microchip5 V high-speed transceiver up to 1 Mbit/s, the part beside a huge number of MCP2515 boards.
MCP2561, MCP2562MicrochipThe later high-speed pair. The MCP2562 brings out VIO. Standby mode.
SN65HVD230, 231, 232Texas Instruments3.3 V high-speed family up to 1 Mbit/s. The 230 has slope control and standby, the 231 has a sleep pin, the 232 is the always-on version.
SN65HVD251Texas Instruments5 V high-speed transceiver for 12 V and 24 V nodes.
L9615STHigh-speed transceiver specified to 500 kbaud, with two slope settings.
L9616STThe 1 Mbaud member of the same ST family, AEC-Q100, slope control for 1 Mbaud or 250 kbaud.
MAX3051Analog Devices3.3 V, up to 1 Mbit/s, with slope control, standby and shutdown. The common-mode range is wider than ISO 11898. It is not the automotive fault-voltage part.

CAN FD, up to 2 Mbit/s and 5 Mbit/s

A CAN FD transceiver is still an ISO 11898-2 part. The extra promise is loop-delay symmetry in the data phase. NXP's CAN FD portfolio guarantees that symmetry to 5 Mbit/s. Texas Instruments splits the same idea: the plain TCAN1042 is specified to 2 Mbit/s, and the G suffix to 5 Mbit/s. Infineon states the same 5 Mbit/s ceiling on the TLE9250 and TLE9251, and says the symmetry is good enough that many boards drop the common-mode choke.

FamilyMakerWhat distinguishes it
TJA1042, including B and CNXPStandby and bus wake-up, 12 V and 24 V, FD to 5 Mbit/s. B and C shorten the propagation delay for a larger network. Some variants have VIO, some have SPLIT.
TJA1043NXPThe FD part with fail-safe diagnostics and a fuller power-management scheme.
TJA1044, TJA1044VNXPStandby, aimed at automotive nodes. The V variant is the VIO version.
TJA1049NXPStandby with bus wake-up, biased toward low emission and ESD.
TJA1051NXPFD transceiver for nodes that do not need standby. /3 is VIO, /E is a low-current off mode. NXP now points new designs at the TJA1057.
TJA1057NXPThe current recommendation in place of the TJA1051, in the same role.
TJA1059NXPTwo high-speed transceivers in one package.
UJA1161A, UJA1162A, UJA1166ANXPFD transceivers with their own 5 V CAN supply. Standby on the UJA1161A, sleep on the UJA1162A, and a 5 V output for other loads on the UJA1166A.
TLE9250InfineonFD to 5 Mbit/s, no separate wake supply. The cost-optimised member of the family.
TLE9251, TLE9351BInfineonFD to 5 Mbit/s with standby. The wake receiver can be supplied from VIO. The B generation is the current migration target.
TLE9252, TLT9252InfineonTwo supplies, so the bus side stays up while the logic supply dips in cranking. TLT parts are the higher-temperature Endurance grades, to 150 °C ambient.
TLE9254, TLE9350BInfineonThe FD family with and without VIO. TLE9350B is the later, cost-optimised generation.
TCAN1042-Q1, TCAN1042V-Q1Texas InstrumentsFD, standby, bus fault to ±58 V. Plain parts to 2 Mbit/s, G parts to 5 Mbit/s. V is the I/O level shift. Fault protection and a passive unpowered bus.
TCAN1044A-Q1Texas InstrumentsThe newer standby part Texas Instruments names as the upgrade from the TCAN1042.
TCAN1051-Q1Texas InstrumentsSilent mode, so the node can listen without driving. Classic CAN and FD to 2 Mbit/s, and to 5 Mbit/s with the G suffix. V is the I/O supply. Bus fault is ±58 V, or ±70 V on the H variants.
TCAN330, TCAN332, TCAN334, TCAN337Texas Instruments3.3 V parts to 1 Mbit/s, sharing a bus with 5 V transceivers. The G suffix on each, TCAN330G through TCAN337G, adds FD timing to 5 Mbit/s. Silent mode is on the 330 and 337, standby with wake on the 334, and the 332 is normal mode only. Bus fault protection is ±14 V.
MCP2561FD, MCP2562FDMicrochipFD timing specified at 2, 5 and 8 Mbit/s, with standby. One variant has the SPLIT pin and the other has VIO from 1.8 V to 5.5 V.
ATA6560, ATA6561 and the ATA656x familyMicrochipAutomotive high-speed and FD transceivers from the former Atmel line. Standby, and VIO on the variants that have it.
NCV7344onsemiFD timing specified to 5 Mbit/s, standby with bus wake-up, VIO on the -3 version. Follows the NCV734x series and the earlier AMIS42665 and AMIS-30660.

Signal improvement, and partial networking

Signal-improvement parts stay inside ISO 11898-2 and add the behaviour in CiA 601-4. They are sold as pin-compatible replacements for the ordinary FD transceivers. NXP's TJA1462 replaces a TJA1042 footprint. Texas Instruments' TCAN1462-Q1 replaces a TCAN1042-Q1 or TCAN1044A-Q1 footprint. Infineon's TLE9371 replaces a TLE9251 or TLE9351 footprint. The data phase these families advertise, where the wiring allows it, is 8 Mbit/s. NXP also lists a CAN SIC XL category aimed at 20 Mbit/s. That is a separate transceiver mode, using the pulse-width signalling the CAN page already distinguishes from ordinary CAN FD.

PartMakerStatus and role
TJA1462NXPSIC with standby. The drop-in for a TJA1042-class node.
TJA1463NXPSIC with sleep.
TJA1464, TJA1467, TJA1468NXPFurther SIC parts. NXP was listing these as preproduction, the TJA1468 as a dual channel.
TJA1465, TJA1466NXPSIC with partial networking. NXP was listing these as under development.
TCAN1462-Q1, TCAN1462V-Q1Texas InstrumentsSIC with standby, ±58 V bus fault, VIO down to 1.8 V on the V part. Specified for networks that want 5 Mbit/s or 8 Mbit/s with stubs.
TLE9371SJ, TLE9371VSJInfineonSIC with bus wake-up. The V part has VIO. Infineon states ISO 11898-2:2024 and backwards behaviour at 1, 2 and 5 Mbit/s.

Partial networking is the selective wake-up. The transceiver watches the identifiers and, on the parts that allow it, a slice of the data field, and only then wakes the microcontroller.

PartMakerWhat it wakes on
TJA1145ANXPFD partial networking to 5 Mbit/s, ISO 11898-2:2016.
TLE9255W, TLT9255WInfineonSPI-configured wake identifier up to 29 bits and data up to 64 bits. Can be set to ignore a CAN FD payload so a classic controller can share the wire. Sleep current is specified under 26 µA. The TLT grade is the hotter Endurance part.
TCAN1145-Q1Texas InstrumentsAutomotive FD partial-networking transceiver. Texas Instruments publishes an evaluation board for it.
UJA1169NXPA system-basis chip whose transceiver can be CAN FD-passive and still do selective wake-up, so the microcontroller need not understand FD frames while it is asleep.

Secure, isolated, fault-tolerant, single-wire

The TJA1152 is NXP's secure high-speed transceiver. It behaves as a normal FD transceiver until it sees a frame its configuration does not allow: a spoofed identifier, a flooded bus, or a tampered message. It then contains that traffic without a cryptographic stack in the microcontroller. The TJA1152A has VIO. The arbitration rate is 125, 250 or 500 kbit/s, and the data phase is two or four times that.

Isolated transceivers put the barrier in the same package as the driver. They are the parts on a battery-management board, a 48 V rail, or a charger, where the bus ground is not the logic ground.

PartMakerIsolation and rate
TJA1052i, grades /1, /2 and /5NXPCapacitive isolation, FD to 5 Mbit/s. The three grades are the three isolation voltages in the SO16. Aimed at electric and hybrid vehicles.
ISO1042, ISO1042-Q1Texas InstrumentsIsolated FD. Classic CAN to 1 Mbit/s and FD to 5 Mbit/s, 5 kV RMS, bus fault ±70 V, logic supply from 1.8 V to 5 V.
ISO1044Texas InstrumentsThe smaller isolated FD part, 5 Mbit/s, 3 kV RMS, bus fault ±58 V.
ISOW1050Texas InstrumentsIsolated transceiver to 5 Mbit/s with the isolated supply in the same package, 5 kV RMS, bus fault ±58 V.
ADM3050EAnalog DevicesIsolated FD with iCoupler and an on-chip isolated supply. About 5 kV RMS, ±40 V bus pins, ±25 V common mode.
ADM3055E, ADM3057EAnalog DevicesThe same isolation idea with standby, and a silent mode that lets a controller hunt the bit rate without driving error frames.
ADM3056EAnalog DevicesIsolated FD with the low-power mode and without the integrated power of the ADM3055E.

Fault-tolerant transceivers are ISO 11898-3, 125 kbit/s, and they are a different pinout and a different voltage. The TJA1054 and the later TJA1055 drive a differential pair and, if one wire shorts, carry on with the surviving wire. The TJA1055 is NXP's enhanced TJA1054: lower sleep current, better ESD, and wake-up indicated even when VCC is down. The TJA1054 itself replaced the PCA82C252 and the TJA1053. Up to 32 nodes. Putting a high-speed 120 ohm transceiver on this network, or the other way round, does not make a working bus.

Single-wire transceivers are SAE J2411, one wire and ground, normal traffic near 33.3 kbit/s and a high-speed download near 83.3 kbit/s while a service tool holds the extra load. The high-speed mode is for that download. It is not the rate of the body bus in ordinary driving.

PartMakerNotes
NCV7356onsemiJ2411 and GMW3089. Supply 5 V to 27 V. Normal rate typically 33 kbit/s, high-speed typically 83 kbit/s, with the part capable of 40 kbit/s and 100 kbit/s. SO8 and SO14. Sleep under 60 µA.
TH8056MelexisGMW3089 and J2411. The same two rates. SO8 and a thermally enhanced SO14 with an inhibit pin for an external regulator.
AU5790NXPThe earlier Philips single-wire part. 33.3 kbit/s with 32 nodes, 83 kbit/s high-speed mode, waveshaping, load-dump protection. The SO8 shares the later single-wire pinout.
MC33897NXPThe Freescale single-wire transceiver, sold in the 14-pin package.
TLE6255InfineonThe earlier single-wire transceiver, 14-pin. Hardware notes now list it as obsolete, with the NCV7356 and the TH8056 in the same role.

Controllers and system-basis chips

The transceiver is not the protocol. These are the chips that hand it TXD and RXD, or that hide both behind SPI.

PartMakerRole
SJA1000NXPThe standalone classic CAN controller of the 1990s and 2000s. Parallel bus, acceptance filter with its own mask polarity. Still the core inside a lot of older interface hardware.
MCP2515MicrochipSPI classic CAN controller, almost always paired with an MCP2551 or MCP2562.
MCP2517FD, MCP2518FDMicrochipSPI CAN FD controllers. The MCP2518FD is the later one.
MCP25625MicrochipMCP2515 controller and a transceiver in one package.
TCAN4550Texas InstrumentsBosch M_CAN and a FD transceiver behind SPI. The product page states bus rates up to 5 Mbit/s, with standby, sleep and wake from the bus or a local pin. The way a processor with no CAN peripheral still sits on the pair.
UJA1169NXPMini system-basis chip: FD transceiver, 5 V or 3.3 V regulator at 250 mA, watchdog, SPI, and partial networking on the variants that have it. Six supply combinations.
TLE926x, TLE927x, TLE9461, TLE9471InfineonOPTIREG system-basis chips. The CAN transceiver is one block inside a regulator, watchdog and wake-up device.

The parts on the same copper

NXP's application notes for the TJA1050 and the TJA1041 draw the same network between the transceiver and the connector, and it is what a repair turns up there.

Termination is two 60 ohm resistors in series across CANH and CANL, or one 120 ohm, at each end of the bus and nowhere else. The midpoint of the split pair can go to the SPLIT pin through a capacitor. A third 120 ohm, added because a drawing showed one, is the fault the CAN page already warns about.

The clamp is a low-capacitance dual diode at the connector. NXP specifies the PESD1CAN, about 11 pF, for this job, and an ECU with both that diode and a choke was measured above 20 kV. onsemi's NUP2105L is the dual TVS its CAN protection note puts in the same position. The diode sits at the connector. The choke sits at the transceiver.

The choke is a common-mode part. NXP asks for stray inductance under 500 nH, which is what a bifilar winding gives, and names the B82789-C104 as the example. A choke with more leakage rings against the pin capacitance and can make RXD toggle twice on one edge. Texas Instruments measured that ringing on a set of production chokes. The values that show up on CAN boards are 51 µH and 100 µH.

ChokeMakerWhere it is specified
B82789-C104EPCOS100 µH. The part NXP draws next to the TJA1050.
B82789C0223, B82789C0513EPCOS22 µH and 51 µH. Both are in the set Texas Instruments measured.
B82799C0474EPCOS470 µH. Included in that same measurement set. A larger inductance is not automatically a better CAN choke.
ACT45B-510-2P, ACT45B-101-2PTDK51 µH and 100 µH. In the Texas Instruments measurement set.
ACT1210-101-2PTDK100 µH in the 1210 size.
B82787C0104EPCOS100 µH, the EPCOS part in the same distributor lists as the ACT45B.
DLW43SH510, DLW43SH101Murata51 µH and 100 µH. The 100 µH part is also listed at 100 mA.
DLW32SH101Murata100 µH, the 1210 size those lists mark for CAN FD.
PE-1210ACC101Pulse100 µH in 1210.

A newer FD transceiver is often specified to pass the vehicle EMC test with no choke at all. Fitting one anyway is a system choice. Fitting a large toroid because it is also 100 µH is the choice Texas Instruments' measurements argue against: the leakage, not the common-mode inductance, is what rings.

Sources

  • CAN FD portfolio. NXP. TJA1042, TJA1043, TJA1044, TJA1049, TJA1051, TJA1052i, TJA1057, TJA1059, TJA1145A and the UJA116x. Accessed 2026-11-12.
  • CAN SIC portfolio. NXP. TJA1462, TJA1463 and the later TJA146x, including which were preproduction. Accessed 2026-11-12.
  • TJA1042. NXP. 5 Mbit/s FD timing, VIO, SPLIT, and the B and C delay grades. Accessed 2026-11-12.
  • Upgrading from the PCA82C250 and PCA82C251. NXP. TJA1040 and TJA1050 as the successors, with the supply, standby and bus-pin limits. Accessed 2026-11-12.
  • TJA1055. NXP. Fault-tolerant transceiver, 125 kbit/s, single-wire fallback. Accessed 2026-11-12.
  • TJA1152. NXP. Secure FD transceiver, allowed arbitration rates and data-phase ratios. Accessed 2026-11-12.
  • TJA1052i. NXP. Isolated FD transceiver to 5 Mbit/s. Accessed 2026-11-12.
  • UJA1169. NXP. System-basis chip, regulator current, and CAN FD-passive selective wake-up. Accessed 2026-11-12.
  • TJA1050 application note. NXP. Choke, split termination, PESD1CAN, and the 500 nH stray-inductance limit. Accessed 2026-11-12.
  • Automotive CAN transceivers. Infineon. TLE9350B, TLE9351B, TLE9255W, TLT grades and the TLE9371 SIC family. Accessed 2026-11-12.
  • TCAN1042V-Q1. Texas Instruments. 2 Mbit/s and 5 Mbit/s grades, ±58 V, VIO. Accessed 2026-11-12.
  • TCAN4550. Texas Instruments. SPI CAN FD controller with an integrated transceiver. Accessed 2026-11-12.
  • ISO1042. Texas Instruments. Isolated FD, 5 Mbit/s, 5 kV RMS, ±70 V bus fault. Accessed 2026-11-12.
  • ISO1044. Texas Instruments. Isolated FD transceiver, 5 Mbit/s, 3 kV RMS. Accessed 2026-11-12.
  • ISOW1050. Texas Instruments. Isolated transceiver to 5 Mbit/s with an on-chip isolated supply. Accessed 2026-11-12.
  • TCAN330 family. Texas Instruments. 3.3 V transceivers, 1 Mbit/s, and 5 Mbit/s on the G suffix. Accessed 2026-11-12.
  • TCAN1051-Q1. Texas Instruments. Silent mode, 2 Mbit/s, 5 Mbit/s on the G suffix. Accessed 2026-11-12.
  • MCP2561FD and MCP2562FD. Microchip. FD timing at 2, 5 and 8 Mbit/s, SPLIT and VIO. Accessed 2026-11-12.
  • Common-mode chokes in CAN networks. Texas Instruments. Measured chokes, including ACT45B, B82789 and DLW43SH. Accessed 2026-11-12.
  • NCV7344. onsemi. FD to 5 Mbit/s, and the earlier AMIS42665 generation. Accessed 2026-11-12.
  • NCV7356. onsemi. Single-wire CAN, 33 kbit/s and 83 kbit/s. Accessed 2026-11-12.
  • TH8056. Melexis. Single-wire CAN to GMW3089 and J2411. Accessed 2026-11-12.
  • AU5790. NXP. Single-wire transceiver, 33.3 kbit/s and 83 kbit/s. Accessed 2026-11-12.
  • Single-wire CAN breakout. Beyondlogic. The shared SO8 pinout, and the MC33897 and TLE6255 as the 14-pin parts. Accessed 2026-11-12.
  • SN65HVD230. Texas Instruments. 3.3 V high-speed transceiver. Accessed 2026-11-12.
  • L9616. ST. High-speed transceiver to 1 Mbaud. Accessed 2026-11-12.
  • MAX3051. Analog Devices. 3.3 V transceiver to 1 Mbit/s. Accessed 2026-11-12.
  • MCP2562. Microchip. High-speed transceiver with standby and VIO. Accessed 2026-11-12.
  • Galvanically isolated CAN FD. CAN in Automation, 2019. ADM3050E, ADM3055E, ADM3056E and ADM3057E. Accessed 2026-11-12.