Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Citroën, Peugeot

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

The AL4 is a transverse four-speed automatic. A lock-up torque converter feeds two Simpson epicyclic trains, a step-down gear and a differential with sealed outputs. A Siemens ECU with fuzzy-logic laws controls the converter, the shifts and the driver programs. The stated torque capacity is 210 N·m. The unit is sealed. Oil is cooled in a water–oil heat exchanger, and the ECU is tied to the engine ECU so that shift quality, mechanical protection and the emissions limits are handled together.

The rear housing carries the component reference and the serial number. The ECU label carries the Siemens reference and serial number, the software version, the hardware version and the customer number. Diagnostic identity is read with the factory tool on the K-line. The ECU is a 56-track Flash unit.

Gear train

The Simpson arrangement joins two simple epicyclic trains. Planet carrier PS1 is connected to ring C2, and planet carrier PS2 is connected to ring C1. Train 1 sits on the rear-housing side. Train 2 sits on the converter side, and the output always leaves through planet carrier PS2 into the primary step-down pinion.

Tooth counts are sun P1 33, sun P2 40, planet S1 21, planet S2 19, ring C1 81 and ring C2 80. The elements that drive and react in each gear, and the resulting ratios, are:

GearDrivingReactionRatio 1P1P22.72 2PS1–C2P21.5 3P1 and PS1–C2none1 4PS1–C2P10.71 ReverseP1PS1–C22.45

The friction elements are clutch E1 for reverse and 1st, clutch E2 for 2nd, 3rd and 4th, brake F1 for 4th, brake F2 for reverse, and brake F3 for 1st and 2nd. The hydraulic block (DH) contains the manual valve. An auxiliary block (DHA) sits with it. A park wheel locks the transmission in P.

Converter and lock-up

The converter is bolted to the engine drive plate. The impeller is driven by the engine, the turbine drives the gearbox, and the stator sits on a freewheel between them. In the converter phase, torque is multiplied by up to 2.2. In the coupling phase the efficiency is 0.98, and it is 1 when the lock-up clutch is closed.

Lock-up is hydraulic. The ECU decides it from vehicle speed, throttle position and the gear engaged, and an electrovalve reverses the oil flow. Unlocked, pressure on the lock-up circuit lifts the piston off the friction plate and oil then feeds the converter. Locked, the lock-up circuit is opened to the tank, oil arriving through the converter circuit pushes the piston on, and the turbine is joined to the impeller through the damper and the double-sided plate. Lock-up is used in 2nd, 3rd and 4th, and in 1st only in rare cases. Closing it gives engine braking, lowers fuel use and cools the oil by stopping converter slip.

Hydraulic control

The engine-driven pump supplies line pressure to the hydraulic block, which feeds the brakes, the clutches, the converter, the lock-up clutch and the lubrication. The solenoids sit in a hydraulic accumulator.

Six sequence valves, EVS1 to EVS6, select the elements. EVM1 modulates line pressure. EVM2 modulates the lock-up clutch. The manual valve VM moves with the selector. A further electrovalve, EPDE, modulates flow through the heat exchanger and can bypass it.

Line pressure is closed-loop. The reference is the turbine torque that has to be held. When a shift is ordered, the ECU drives the electrovalves in a fixed order with timers that depend on engine load and road speed, so the element that is emptying and the element that is filling overlap. During the shift the transmission ECU asks the engine ECU for a brief ignition retard, taken from a table the engine ECU supplies, so torque drops while the elements exchange. Idle speed is raised through the engine ECU to offset the drag of a gear being engaged.

Selector, programs and laws

The lever works the multifunction switch and the manual valve through the selector shaft. The grid is P, R, N, D, 3, 2. A radial movement of the lever releases the mechanical safety. With the ignition on, shift-lock holds the lever in P until the brake pedal is pressed. Position 2 is the position from which a separate “1” button imposes 1st, where that button is fitted. Later cars add a sequential gate: M for manual selection, “+” for one gear up and “−” for one gear down. On that gearbox the electrical state of P, R, N and D still comes from multifunction switch 1600, and sequential control 1603 is wired straight to the ECU.

The readable part of the sequential switch logic is:

DMM+M− S11010 S21001

Contacts S3 to S6 and the Park/Neutral contact exist on the switch. Their levels depend on the car, so a continuity check follows the diagram for that car.

The ECU holds ten shift laws: six adaptive laws, a snow law, an unlocked law for low temperature, a cold depollution law that heats the catalyst, and a transmission-temperature protection law. The six adaptive laws split into three for driving style (economy, medium, sport) and three for road and load (gentle slope, steep slope, downhill). After a law change, a short gear lock stops an immediate further shift. A sudden lift of the accelerator suppresses the upshift so engine braking stays. Sustained braking is used to anticipate downshifts. A double downshift, 4th to 2nd or 3rd to 1st, is allowed. A sudden full press in the normal program temporarily selects a sportier law. Kick-down is ordered by the transmission ECU at full accelerator and still depends on road speed. The gearbox will not change up at no load.

Three driver programs sit on buttons beside the lever. Normal is the base program and is restored at every ignition cycle. Sport keeps automatic shifts and moves the laws towards performance. Snow, on low-grip ground, drops 1st or both 1st and 2nd out of Drive and makes downshifts less frequent. In the imposed positions 1, 2 and 3 the snow laws still respect the limit of the position the lever is in. The gear and the program are shown on the instrument panel. A buzzer for leaving the car out of P is fitted on some versions. The multifunction switch also drives the reversing lamps and inhibits cranking unless the lever is in P or N.

Reverse is inhibited above a road-speed threshold. A shift from N into D or R is refused if engine speed is above a threshold, and is allowed once speed falls or a timer expires. The numeric thresholds are calibration values.

What the ECU exchanges with the engine

Engine load reaches the transmission in one of three ways: a double-track throttle potentiometer, a single-track potentiometer, or, on a diesel with a mechanical pump, a potentiometer on the pump load lever. The injection ECU supplies engine torque, engine speed and coolant temperature. The transmission ECU returns a torque-reduction request, an idle-compensation request, and, on L4 emissions and above, a request to light the engine-management warning when a transmission fault makes emissions worse. Kick-down can also be a switch on the accelerator cable. Petrol cars with a motorised throttle use the throttle-housing procedure instead of the cable pedal-programming routine.

The gearbox-side inputs are oil temperature, oil pressure, input (turbine) speed, output speed, the multifunction switch, the program buttons, the brake switch and its redundant contact, and the “1” button. Outputs drive the sequence valves, the pressure and lock-up modulators, the heat-exchanger valve, the shift-lock, the instrument display and the starter-prevention relay.

Connector

Supply, valve drives and the main sensors use the 56-track ECU connector. Pins that the listing gives two jobs are marked. The wiring diagram for the car decides which job that pin has.

PinFunction 1Supply to sequence valves EVS1–EVS6 2Supply to the heat-exchanger flow valve 3Air-conditioning compressor cut, unused on this listing 4Instrument-panel display 5Torque-reduction request and idle compensation 6Version-dependent: torque reduction and idle compensation, unused, or the EOBD-lamp request on the L4 version 7EVS3 earth 8EVS4 earth 9EVS2 earth 10EVS1 earth 11Shift-lock actuator 12Heat-exchanger oil-flow valve (EPDE) 13EVS5 earth 14EVS6 earth 15Kick-down input 16Redundant brake contact (opening contact) 17L diagnostic line 18K diagnostic line 19Lock-up valve 20Main-pressure valve 22Engine-torque input 23Listed as unused, and also as throttle position (driver demand) 24Oil-pressure sensor supply + 25Oil-pressure sensor supply − 26Supply to the pressure and lock-up modulating valves 27Ignition positive 28ECU earth, common with the engine ECU 29–30CAN high and CAN low 31Multifunction switch S2 32Multifunction switch S3 33Multifunction switch S4 34Park/Neutral contact 36“1” button 37Multifunction switch S1 38–39A second CAN high and CAN low pair is also listed 40Snow button 41Normal/Sport button 42Electronic earth for the multifunction switch 43Stop-lamp contact (closing contact) 45Turbine-speed sensor + 46Turbine-speed sensor − 47Output-speed sensor − 48Output-speed sensor + 49Engine speed (TDC) 51Listed as the double-track throttle-potentiometer negative supply, and also as unused 52Throttle-potentiometer positive supply, double-track version 53Oil-temperature probe − 54Oil-temperature probe + 55Line-pressure signal 56Listed as the throttle-potentiometer signal, and also as battery positive

On the gearbox, a blue 3-pin plug is the heat-exchanger bypass solenoid, a yellow 3-pin plug is the input-speed sensor, a green 3-pin plug is the oil-pressure sensor, a yellow 12-pin plug is the hydraulic block and oil temperature, and a green 12-pin plug is the multifunction switch.

Oil level and the oil counter

New units are filled. The grade and the total capacity follow the car. The level check is not part of pre-delivery or the first service. The transmission must be out of a downgraded mode, and the car must be level.

Remove the filler plug and add 0.5 litre at the start of every check. Hold the brake and pass through every gear. With the lever in P, the engine idling and the oil at 60 °C, remove the level plug. The level is correct when oil streams and then drips. If it only drips, or does not flow, refit the plug, stop the engine, add another 0.5 litre and repeat. Filler and level plugs tighten to 2.4 m·daN (24 N·m). Too much oil heats and leaks. Too little oil damages the unit.

A later workshop method checks the level only with the drain plug removed, and drains by unscrewing the overflow tube with an Allen key. The plug evolution includes a sealing washer. The method follows the casing on the car: some casings have a separate level plug, and the later check is the overflow tube inside the drain plug.

The ECU counts oil age from oil temperature and the time spent hot. At the calibrated maximum the Sport and Snow lamps flash together to call for an oil change. After an oil change, or a transmission replacement, initialise the counter. If the ECU is replaced and the oil is not changed, copy the counter from the old ECU into the new one. If the old counter cannot be read, change the oil. Burnt oil means the heat exchanger is replaced with the transmission.

Download, configuration and pedal programming

The ECU adapts continuously by storing the difference between a reference and the value it measures. After a transmission, an ECU or another transmission component is replaced, the road test has to run frequent shifts through every gear and every program. That test is what rebuilds shift quality.

Downloading the transmission ECU is always paired with downloading the engine ECU. The download is followed by pedal programming, configuration and the road test. A new or freshly downloaded ECU is configured for the three options the car actually has: shift-lock, air conditioning, and EOBD (L4). Configuring them stops the diagnostics looking for hardware that is not fitted.

Pedal programming is required after ECU replacement, transmission replacement, a download, accelerator-cable replacement or adjustment, engine-ECU replacement or download, throttle-potentiometer replacement, and diesel injection-pump replacement. After cable work, the kick-down switch is checked as well. Cars with a motorised throttle use the throttle-housing procedure instead of this pedal routine.

WorkWhat follows it TransmissionAdjust the multifunction switch, initialise the oil counter, road test. The new unit arrives filled. Oil changeInitialise the oil counter. Hydraulic distributor or its valvesAdjust the internal control, then road test. The setting uses a screw and a shim for the internal selector. Input-speed, output-speed or pressure sensorDo not drain. Check the level. Oil-temperature probeThe probe is in the distributor. Drain, remove the distributor and the internal harness, adjust the internal control, check the level. Transmission ECUCopy the oil counter, configure, write the counter back, program the pedal, road test, and download the engine ECU. Injection ECUProgram the pedal and download the transmission ECU.

Downgraded modes

Sport and Snow lamps flashing together mean the oil is too hot (they go out once it cools), the oil counter is at its maximum, the serial link to the instrument panel is broken, or a stored fault is present. Faults that flash the lamps include the ECU and its supply, the oil-pressure sensor, the sequence-valve supply, main-pressure regulation, the multifunction switch, the sequence valves, the pressure and lock-up modulators, the heat-exchanger valve, an unprogrammed accelerator pedal, a speed comparison that fails (input against output, input against engine, output against engine), engine speed, pedal position, and the analogue-sensor supply.

LevelTypical causeBehaviour 1Kick-down inputTransmission operation is unchanged. 2Oil temperature, engine-torque information, display, shift-lockComfort is affected. The degradation is small. 3Vehicle speed, lock-up valve, torque-reduction output, pressure sensor, sensor supply, brake switch, heat-exchanger valve, or throttle position lost together with torqueShift quality falls and functions are lost. 4Engine speed, or the input-speed sensorFunctions are lost or downgraded. 5Throttle potentiometer, engine torque, multifunction switch, analogue supply, pressure valve, main-pressure regulation, heat-exchanger valve control, or a failed speed comparisonHydraulic 3rd at the next ignition-on. If the car is in 4th, 4th is kept until that ignition cycle. This is the deferred stopping mode. Reverse-gear safety while driving is lost with the multifunction-switch fault. 6ECU failed, sequence valves or their supply, or the accelerator pedal not programmedHydraulic 3rd immediately. This is the stopping mode.

In stopping mode a shift from P to R or from N to R can bang. In hydraulic emergency mode the gear-change safety limits are dropped. A loud engagement is a reason to read the fault memory before condemning a clutch.

Faults that have a mechanical cause

A metallic rattle at low mileage, on units built from September to December 2003, comes from the paper face of the F1 brake discs. Driving the car through 3rd–4th shifts beds F1 in. The discs are not replaced for that noise.

A flare of 400 to 500 rpm on a cold 1st-to-2nd shift, with slip only when cold, is the emissions shift law. It is the calibration, and it is not cured by a clutch repair.

Judder in 4th around 45 mph is F3 cocking and dragging on its drum. F3 is used in 1st and 2nd. From 9 October 2003 a retaining clip is fitted, and the first gearbox number with it is 592185. In service the gearbox is replaced.

Internal bushes were changed because aluminium bushes wear, lose pressure, slip the clutches and bands, and put the gearbox into backup with oil that smells burnt. The change was described more than once, and the dates do not all agree. The plan that was then carried out, from gearbox serial 859620 on 12 April 2005, replaces the bushes that wear first: the input-shaft bush and the oil-pump-hub bush in bronze LF5, the primary-gear bush in aluminium A590, and the brake-3 drum bush with its bore opened by 0.2 mm. The satellite-carrier bush and the oil-pump-body bush followed later, in LF5. Aluminium remains in the box, so black or discoloured oil on its own is not proof of a failed gearbox. Burnt-smelling oil together with backup mode is the pressure-loss symptom. A six-bush kit exists for reconditioning.

The six bushes and what they do are: input shaft, alignment and clutch-pressure circuit; satellite-carrier 2 in the bell housing, alignment and lubrication; brake 3 drum, lubrication; oil-pump hub, alignment and clutch pressure; oil-pump body, alignment and lubrication; primary gear, alignment.

Difficult selection, judder or slip on C3, C5 and C8, with P0745 or P0932 or both, and with oil pressure that does not move in measurement, points at the oil-pressure sensor. Doubtful manufacture dates, read as 05xxx, are 05237–05238, 05241–05245, 05248–05251 and 05256–05257. The replacement sensor is 2529 24.

Backup with P0745 on any AL4 built before June 2005 that still has the Borg Warner pressure-modulator valves is a slow solenoid, caused by the solenoid spring. The electrovalve evolution number has to be above 05097. Below that, the valve is replaced. Borg Warner valves that are noisy when the car is stationary were a known complaint with no hardware change attached at the time.

On an Xsara HDi, a lack of power with the gearbox in backup and no warning lamp can be engine-torque incoherence in the gearbox ECU. The injection ECU has to be on data block D2 before any other check. A C3 that stores P1762, instrument-panel serial line, at pre-delivery is a software fault in reference 9657229780, version 037, edition 1701, and the fault does not apply to a multiplexed car.

Handling

The pump turns only with the engine, so the drive wheels are raised for a tow. Towing on the wheels is limited to N, with no oil added, and to 30 miles at no more than 30 mph. The car is not driven with the ignition off, and it cannot be push-started. The battery stays connected while the engine is running, and the ECU stays connected while the ignition is on. The electrics are not fed above 16 V, and a test lamp is not used on the ECU wiring. When the transmission is removed, the converter is pinned so it stays in the bell housing, and the centring pin is removed only as the unit is offered up to the engine.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: AL4 automatic transmission

The AL4 is a transverse four-speed automatic. A lock-up torque converter feeds two Simpson epicyclic trains, a step-down gear and a differential with sealed outputs. A Siemens ECU with fuzzy-logic laws controls the converter, the shifts and the driver programs. The stated torque capacity is 210 N·m. The unit is sealed. Oil is cooled in a water–oil heat exchanger, and the ECU is tied to the engine ECU so that shift quality, mechanical protection and the emissions limits are handled together.

The rear housing carries the component reference and the serial number. The ECU label carries the Siemens reference and serial number, the software version, the hardware version and the customer number. Diagnostic identity is read with the factory tool on the K-line. The ECU is a 56-track Flash unit.

Gear train

The Simpson arrangement joins two simple epicyclic trains. Planet carrier PS1 is connected to ring C2, and planet carrier PS2 is connected to ring C1. Train 1 sits on the rear-housing side. Train 2 sits on the converter side, and the output always leaves through planet carrier PS2 into the primary step-down pinion.

Tooth counts are sun P1 33, sun P2 40, planet S1 21, planet S2 19, ring C1 81 and ring C2 80. The elements that drive and react in each gear, and the resulting ratios, are:

GearDrivingReactionRatio
1P1P22.72
2PS1–C2P21.5
3P1 and PS1–C2none1
4PS1–C2P10.71
ReverseP1PS1–C22.45

The friction elements are clutch E1 for reverse and 1st, clutch E2 for 2nd, 3rd and 4th, brake F1 for 4th, brake F2 for reverse, and brake F3 for 1st and 2nd. The hydraulic block (DH) contains the manual valve. An auxiliary block (DHA) sits with it. A park wheel locks the transmission in P.

Converter and lock-up

The converter is bolted to the engine drive plate. The impeller is driven by the engine, the turbine drives the gearbox, and the stator sits on a freewheel between them. In the converter phase, torque is multiplied by up to 2.2. In the coupling phase the efficiency is 0.98, and it is 1 when the lock-up clutch is closed.

Lock-up is hydraulic. The ECU decides it from vehicle speed, throttle position and the gear engaged, and an electrovalve reverses the oil flow. Unlocked, pressure on the lock-up circuit lifts the piston off the friction plate and oil then feeds the converter. Locked, the lock-up circuit is opened to the tank, oil arriving through the converter circuit pushes the piston on, and the turbine is joined to the impeller through the damper and the double-sided plate. Lock-up is used in 2nd, 3rd and 4th, and in 1st only in rare cases. Closing it gives engine braking, lowers fuel use and cools the oil by stopping converter slip.

Hydraulic control

The engine-driven pump supplies line pressure to the hydraulic block, which feeds the brakes, the clutches, the converter, the lock-up clutch and the lubrication. The solenoids sit in a hydraulic accumulator.

Six sequence valves, EVS1 to EVS6, select the elements. EVM1 modulates line pressure. EVM2 modulates the lock-up clutch. The manual valve VM moves with the selector. A further electrovalve, EPDE, modulates flow through the heat exchanger and can bypass it.

Line pressure is closed-loop. The reference is the turbine torque that has to be held. When a shift is ordered, the ECU drives the electrovalves in a fixed order with timers that depend on engine load and road speed, so the element that is emptying and the element that is filling overlap. During the shift the transmission ECU asks the engine ECU for a brief ignition retard, taken from a table the engine ECU supplies, so torque drops while the elements exchange. Idle speed is raised through the engine ECU to offset the drag of a gear being engaged.

Selector, programs and laws

The lever works the multifunction switch and the manual valve through the selector shaft. The grid is P, R, N, D, 3, 2. A radial movement of the lever releases the mechanical safety. With the ignition on, shift-lock holds the lever in P until the brake pedal is pressed. Position 2 is the position from which a separate “1” button imposes 1st, where that button is fitted. Later cars add a sequential gate: M for manual selection, “+” for one gear up and “−” for one gear down. On that gearbox the electrical state of P, R, N and D still comes from multifunction switch 1600, and sequential control 1603 is wired straight to the ECU.

The readable part of the sequential switch logic is:

DMM+M−
S11010
S21001

Contacts S3 to S6 and the Park/Neutral contact exist on the switch. Their levels depend on the car, so a continuity check follows the diagram for that car.

The ECU holds ten shift laws: six adaptive laws, a snow law, an unlocked law for low temperature, a cold depollution law that heats the catalyst, and a transmission-temperature protection law. The six adaptive laws split into three for driving style (economy, medium, sport) and three for road and load (gentle slope, steep slope, downhill). After a law change, a short gear lock stops an immediate further shift. A sudden lift of the accelerator suppresses the upshift so engine braking stays. Sustained braking is used to anticipate downshifts. A double downshift, 4th to 2nd or 3rd to 1st, is allowed. A sudden full press in the normal program temporarily selects a sportier law. Kick-down is ordered by the transmission ECU at full accelerator and still depends on road speed. The gearbox will not change up at no load.

Three driver programs sit on buttons beside the lever. Normal is the base program and is restored at every ignition cycle. Sport keeps automatic shifts and moves the laws towards performance. Snow, on low-grip ground, drops 1st or both 1st and 2nd out of Drive and makes downshifts less frequent. In the imposed positions 1, 2 and 3 the snow laws still respect the limit of the position the lever is in. The gear and the program are shown on the instrument panel. A buzzer for leaving the car out of P is fitted on some versions. The multifunction switch also drives the reversing lamps and inhibits cranking unless the lever is in P or N.

Reverse is inhibited above a road-speed threshold. A shift from N into D or R is refused if engine speed is above a threshold, and is allowed once speed falls or a timer expires. The numeric thresholds are calibration values.

What the ECU exchanges with the engine

Engine load reaches the transmission in one of three ways: a double-track throttle potentiometer, a single-track potentiometer, or, on a diesel with a mechanical pump, a potentiometer on the pump load lever. The injection ECU supplies engine torque, engine speed and coolant temperature. The transmission ECU returns a torque-reduction request, an idle-compensation request, and, on L4 emissions and above, a request to light the engine-management warning when a transmission fault makes emissions worse. Kick-down can also be a switch on the accelerator cable. Petrol cars with a motorised throttle use the throttle-housing procedure instead of the cable pedal-programming routine.

The gearbox-side inputs are oil temperature, oil pressure, input (turbine) speed, output speed, the multifunction switch, the program buttons, the brake switch and its redundant contact, and the “1” button. Outputs drive the sequence valves, the pressure and lock-up modulators, the heat-exchanger valve, the shift-lock, the instrument display and the starter-prevention relay.

Connector

Supply, valve drives and the main sensors use the 56-track ECU connector. Pins that the listing gives two jobs are marked. The wiring diagram for the car decides which job that pin has.

PinFunction
1Supply to sequence valves EVS1–EVS6
2Supply to the heat-exchanger flow valve
3Air-conditioning compressor cut, unused on this listing
4Instrument-panel display
5Torque-reduction request and idle compensation
6Version-dependent: torque reduction and idle compensation, unused, or the EOBD-lamp request on the L4 version
7EVS3 earth
8EVS4 earth
9EVS2 earth
10EVS1 earth
11Shift-lock actuator
12Heat-exchanger oil-flow valve (EPDE)
13EVS5 earth
14EVS6 earth
15Kick-down input
16Redundant brake contact (opening contact)
17L diagnostic line
18K diagnostic line
19Lock-up valve
20Main-pressure valve
22Engine-torque input
23Listed as unused, and also as throttle position (driver demand)
24Oil-pressure sensor supply +
25Oil-pressure sensor supply −
26Supply to the pressure and lock-up modulating valves
27Ignition positive
28ECU earth, common with the engine ECU
29–30CAN high and CAN low
31Multifunction switch S2
32Multifunction switch S3
33Multifunction switch S4
34Park/Neutral contact
36“1” button
37Multifunction switch S1
38–39A second CAN high and CAN low pair is also listed
40Snow button
41Normal/Sport button
42Electronic earth for the multifunction switch
43Stop-lamp contact (closing contact)
45Turbine-speed sensor +
46Turbine-speed sensor −
47Output-speed sensor −
48Output-speed sensor +
49Engine speed (TDC)
51Listed as the double-track throttle-potentiometer negative supply, and also as unused
52Throttle-potentiometer positive supply, double-track version
53Oil-temperature probe −
54Oil-temperature probe +
55Line-pressure signal
56Listed as the throttle-potentiometer signal, and also as battery positive

On the gearbox, a blue 3-pin plug is the heat-exchanger bypass solenoid, a yellow 3-pin plug is the input-speed sensor, a green 3-pin plug is the oil-pressure sensor, a yellow 12-pin plug is the hydraulic block and oil temperature, and a green 12-pin plug is the multifunction switch.

Oil level and the oil counter

New units are filled. The grade and the total capacity follow the car. The level check is not part of pre-delivery or the first service. The transmission must be out of a downgraded mode, and the car must be level.

Remove the filler plug and add 0.5 litre at the start of every check. Hold the brake and pass through every gear. With the lever in P, the engine idling and the oil at 60 °C, remove the level plug. The level is correct when oil streams and then drips. If it only drips, or does not flow, refit the plug, stop the engine, add another 0.5 litre and repeat. Filler and level plugs tighten to 2.4 m·daN (24 N·m). Too much oil heats and leaks. Too little oil damages the unit.

A later workshop method checks the level only with the drain plug removed, and drains by unscrewing the overflow tube with an Allen key. The plug evolution includes a sealing washer. The method follows the casing on the car: some casings have a separate level plug, and the later check is the overflow tube inside the drain plug.

The ECU counts oil age from oil temperature and the time spent hot. At the calibrated maximum the Sport and Snow lamps flash together to call for an oil change. After an oil change, or a transmission replacement, initialise the counter. If the ECU is replaced and the oil is not changed, copy the counter from the old ECU into the new one. If the old counter cannot be read, change the oil. Burnt oil means the heat exchanger is replaced with the transmission.

Download, configuration and pedal programming

The ECU adapts continuously by storing the difference between a reference and the value it measures. After a transmission, an ECU or another transmission component is replaced, the road test has to run frequent shifts through every gear and every program. That test is what rebuilds shift quality.

Downloading the transmission ECU is always paired with downloading the engine ECU. The download is followed by pedal programming, configuration and the road test. A new or freshly downloaded ECU is configured for the three options the car actually has: shift-lock, air conditioning, and EOBD (L4). Configuring them stops the diagnostics looking for hardware that is not fitted.

Pedal programming is required after ECU replacement, transmission replacement, a download, accelerator-cable replacement or adjustment, engine-ECU replacement or download, throttle-potentiometer replacement, and diesel injection-pump replacement. After cable work, the kick-down switch is checked as well. Cars with a motorised throttle use the throttle-housing procedure instead of this pedal routine.

WorkWhat follows it
TransmissionAdjust the multifunction switch, initialise the oil counter, road test. The new unit arrives filled.
Oil changeInitialise the oil counter.
Hydraulic distributor or its valvesAdjust the internal control, then road test. The setting uses a screw and a shim for the internal selector.
Input-speed, output-speed or pressure sensorDo not drain. Check the level.
Oil-temperature probeThe probe is in the distributor. Drain, remove the distributor and the internal harness, adjust the internal control, check the level.
Transmission ECUCopy the oil counter, configure, write the counter back, program the pedal, road test, and download the engine ECU.
Injection ECUProgram the pedal and download the transmission ECU.

Downgraded modes

Sport and Snow lamps flashing together mean the oil is too hot (they go out once it cools), the oil counter is at its maximum, the serial link to the instrument panel is broken, or a stored fault is present. Faults that flash the lamps include the ECU and its supply, the oil-pressure sensor, the sequence-valve supply, main-pressure regulation, the multifunction switch, the sequence valves, the pressure and lock-up modulators, the heat-exchanger valve, an unprogrammed accelerator pedal, a speed comparison that fails (input against output, input against engine, output against engine), engine speed, pedal position, and the analogue-sensor supply.

LevelTypical causeBehaviour
1Kick-down inputTransmission operation is unchanged.
2Oil temperature, engine-torque information, display, shift-lockComfort is affected. The degradation is small.
3Vehicle speed, lock-up valve, torque-reduction output, pressure sensor, sensor supply, brake switch, heat-exchanger valve, or throttle position lost together with torqueShift quality falls and functions are lost.
4Engine speed, or the input-speed sensorFunctions are lost or downgraded.
5Throttle potentiometer, engine torque, multifunction switch, analogue supply, pressure valve, main-pressure regulation, heat-exchanger valve control, or a failed speed comparisonHydraulic 3rd at the next ignition-on. If the car is in 4th, 4th is kept until that ignition cycle. This is the deferred stopping mode. Reverse-gear safety while driving is lost with the multifunction-switch fault.
6ECU failed, sequence valves or their supply, or the accelerator pedal not programmedHydraulic 3rd immediately. This is the stopping mode.

In stopping mode a shift from P to R or from N to R can bang. In hydraulic emergency mode the gear-change safety limits are dropped. A loud engagement is a reason to read the fault memory before condemning a clutch.

Faults that have a mechanical cause

A metallic rattle at low mileage, on units built from September to December 2003, comes from the paper face of the F1 brake discs. Driving the car through 3rd–4th shifts beds F1 in. The discs are not replaced for that noise.

A flare of 400 to 500 rpm on a cold 1st-to-2nd shift, with slip only when cold, is the emissions shift law. It is the calibration, and it is not cured by a clutch repair.

Judder in 4th around 45 mph is F3 cocking and dragging on its drum. F3 is used in 1st and 2nd. From 9 October 2003 a retaining clip is fitted, and the first gearbox number with it is 592185. In service the gearbox is replaced.

Internal bushes were changed because aluminium bushes wear, lose pressure, slip the clutches and bands, and put the gearbox into backup with oil that smells burnt. The change was described more than once, and the dates do not all agree. The plan that was then carried out, from gearbox serial 859620 on 12 April 2005, replaces the bushes that wear first: the input-shaft bush and the oil-pump-hub bush in bronze LF5, the primary-gear bush in aluminium A590, and the brake-3 drum bush with its bore opened by 0.2 mm. The satellite-carrier bush and the oil-pump-body bush followed later, in LF5. Aluminium remains in the box, so black or discoloured oil on its own is not proof of a failed gearbox. Burnt-smelling oil together with backup mode is the pressure-loss symptom. A six-bush kit exists for reconditioning.

The six bushes and what they do are: input shaft, alignment and clutch-pressure circuit; satellite-carrier 2 in the bell housing, alignment and lubrication; brake 3 drum, lubrication; oil-pump hub, alignment and clutch pressure; oil-pump body, alignment and lubrication; primary gear, alignment.

Difficult selection, judder or slip on C3, C5 and C8, with P0745 or P0932 or both, and with oil pressure that does not move in measurement, points at the oil-pressure sensor. Doubtful manufacture dates, read as 05xxx, are 05237–05238, 05241–05245, 05248–05251 and 05256–05257. The replacement sensor is 2529 24.

Backup with P0745 on any AL4 built before June 2005 that still has the Borg Warner pressure-modulator valves is a slow solenoid, caused by the solenoid spring. The electrovalve evolution number has to be above 05097. Below that, the valve is replaced. Borg Warner valves that are noisy when the car is stationary were a known complaint with no hardware change attached at the time.

On an Xsara HDi, a lack of power with the gearbox in backup and no warning lamp can be engine-torque incoherence in the gearbox ECU. The injection ECU has to be on data block D2 before any other check. A C3 that stores P1762, instrument-panel serial line, at pre-delivery is a software fault in reference 9657229780, version 037, edition 1701, and the fault does not apply to a multiplexed car.

Handling

The pump turns only with the engine, so the drive wheels are raised for a tow. Towing on the wheels is limited to N, with no oil added, and to 30 miles at no more than 30 mph. The car is not driven with the ignition off, and it cannot be push-started. The battery stays connected while the engine is running, and the ECU stays connected while the ignition is on. The electrics are not fed above 16 V, and a test lamp is not used on the ECU wiring. When the transmission is removed, the converter is pinned so it stays in the bell housing, and the centring pin is removed only as the unit is offered up to the engine.

Revision 1: AL4 automatic transmission

The AL4 is a transverse four-speed automatic. A lock-up torque converter feeds two Simpson epicyclic trains, a step-down gear and a differential with sealed outputs. A Siemens ECU with fuzzy-logic laws controls the converter, the shifts and the driver programs. The stated torque capacity is 210 N·m. The unit is sealed. Oil is cooled in a water–oil heat exchanger, and the ECU is tied to the engine ECU so that shift quality, mechanical protection and the emissions limits are handled together.

The rear housing carries the component reference and the serial number. The ECU label carries the Siemens reference and serial number, the software version, the hardware version and the customer number. Diagnostic identity is read with the factory tool on the K-line. The ECU is a 56-track Flash unit.

Gear train

The Simpson arrangement joins two simple epicyclic trains. Planet carrier PS1 is connected to ring C2, and planet carrier PS2 is connected to ring C1. Train 1 sits on the rear-housing side. Train 2 sits on the converter side, and the output always leaves through planet carrier PS2 into the primary step-down pinion.

Tooth counts are sun P1 33, sun P2 40, planet S1 21, planet S2 19, ring C1 81 and ring C2 80. The elements that drive and react in each gear, and the resulting ratios, are:

GearDrivingReactionRatio
1P1P22.72
2PS1–C2P21.5
3P1 and PS1–C2none1
4PS1–C2P10.71
ReverseP1PS1–C22.45

The friction elements are clutch E1 for reverse and 1st, clutch E2 for 2nd, 3rd and 4th, brake F1 for 4th, brake F2 for reverse, and brake F3 for 1st and 2nd. The hydraulic block (DH) contains the manual valve. An auxiliary block (DHA) sits with it. A park wheel locks the transmission in P.

Converter and lock-up

The converter is bolted to the engine drive plate. The impeller is driven by the engine, the turbine drives the gearbox, and the stator sits on a freewheel between them. In the converter phase, torque is multiplied by up to 2.2. In the coupling phase the efficiency is 0.98, and it is 1 when the lock-up clutch is closed.

Lock-up is hydraulic. The ECU decides it from vehicle speed, throttle position and the gear engaged, and an electrovalve reverses the oil flow. Unlocked, pressure on the lock-up circuit lifts the piston off the friction plate and oil then feeds the converter. Locked, the lock-up circuit is opened to the tank, oil arriving through the converter circuit pushes the piston on, and the turbine is joined to the impeller through the damper and the double-sided plate. Lock-up is used in 2nd, 3rd and 4th, and in 1st only in rare cases. Closing it gives engine braking, lowers fuel use and cools the oil by stopping converter slip.

Hydraulic control

The engine-driven pump supplies line pressure to the hydraulic block, which feeds the brakes, the clutches, the converter, the lock-up clutch and the lubrication. The solenoids sit in a hydraulic accumulator.

Six sequence valves, EVS1 to EVS6, select the elements. EVM1 modulates line pressure. EVM2 modulates the lock-up clutch. The manual valve VM moves with the selector. A further electrovalve, EPDE, modulates flow through the heat exchanger and can bypass it.

Line pressure is closed-loop. The reference is the turbine torque that has to be held. When a shift is ordered, the ECU drives the electrovalves in a fixed order with timers that depend on engine load and road speed, so the element that is emptying and the element that is filling overlap. During the shift the transmission ECU asks the engine ECU for a brief ignition retard, taken from a table the engine ECU supplies, so torque drops while the elements exchange. Idle speed is raised through the engine ECU to offset the drag of a gear being engaged.

Selector, programs and laws

The lever works the multifunction switch and the manual valve through the selector shaft. The grid is P, R, N, D, 3, 2. A radial movement of the lever releases the mechanical safety. With the ignition on, shift-lock holds the lever in P until the brake pedal is pressed. Position 2 is the position from which a separate “1” button imposes 1st, where that button is fitted. Later cars add a sequential gate: M for manual selection, “+” for one gear up and “−” for one gear down. On that gearbox the electrical state of P, R, N and D still comes from multifunction switch 1600, and sequential control 1603 is wired straight to the ECU.

The readable part of the sequential switch logic is:

DMM+M−
S11010
S21001

Contacts S3 to S6 and the Park/Neutral contact exist on the switch. Their levels depend on the car, so a continuity check follows the diagram for that car.

The ECU holds ten shift laws: six adaptive laws, a snow law, an unlocked law for low temperature, a cold depollution law that heats the catalyst, and a transmission-temperature protection law. The six adaptive laws split into three for driving style (economy, medium, sport) and three for road and load (gentle slope, steep slope, downhill). After a law change, a short gear lock stops an immediate further shift. A sudden lift of the accelerator suppresses the upshift so engine braking stays. Sustained braking is used to anticipate downshifts. A double downshift, 4th to 2nd or 3rd to 1st, is allowed. A sudden full press in the normal program temporarily selects a sportier law. Kick-down is ordered by the transmission ECU at full accelerator and still depends on road speed. The gearbox will not change up at no load.

Three driver programs sit on buttons beside the lever. Normal is the base program and is restored at every ignition cycle. Sport keeps automatic shifts and moves the laws towards performance. Snow, on low-grip ground, drops 1st or both 1st and 2nd out of Drive and makes downshifts less frequent. In the imposed positions 1, 2 and 3 the snow laws still respect the limit of the position the lever is in. The gear and the program are shown on the instrument panel. A buzzer for leaving the car out of P is fitted on some versions. The multifunction switch also drives the reversing lamps and inhibits cranking unless the lever is in P or N.

Reverse is inhibited above a road-speed threshold. A shift from N into D or R is refused if engine speed is above a threshold, and is allowed once speed falls or a timer expires. The numeric thresholds are calibration values.

What the ECU exchanges with the engine

Engine load reaches the transmission in one of three ways: a double-track throttle potentiometer, a single-track potentiometer, or, on a diesel with a mechanical pump, a potentiometer on the pump load lever. The injection ECU supplies engine torque, engine speed and coolant temperature. The transmission ECU returns a torque-reduction request, an idle-compensation request, and, on L4 emissions and above, a request to light the engine-management warning when a transmission fault makes emissions worse. Kick-down can also be a switch on the accelerator cable. Petrol cars with a motorised throttle use the throttle-housing procedure instead of the cable pedal-programming routine.

The gearbox-side inputs are oil temperature, oil pressure, input (turbine) speed, output speed, the multifunction switch, the program buttons, the brake switch and its redundant contact, and the “1” button. Outputs drive the sequence valves, the pressure and lock-up modulators, the heat-exchanger valve, the shift-lock, the instrument display and the starter-prevention relay.

Connector

Supply, valve drives and the main sensors use the 56-track ECU connector. Pins that the listing gives two jobs are marked. The wiring diagram for the car decides which job that pin has.

PinFunction
1Supply to sequence valves EVS1–EVS6
2Supply to the heat-exchanger flow valve
3Air-conditioning compressor cut, unused on this listing
4Instrument-panel display
5Torque-reduction request and idle compensation
6Version-dependent: torque reduction and idle compensation, unused, or the EOBD-lamp request on the L4 version
7EVS3 earth
8EVS4 earth
9EVS2 earth
10EVS1 earth
11Shift-lock actuator
12Heat-exchanger oil-flow valve (EPDE)
13EVS5 earth
14EVS6 earth
15Kick-down input
16Redundant brake contact (opening contact)
17L diagnostic line
18K diagnostic line
19Lock-up valve
20Main-pressure valve
22Engine-torque input
23Listed as unused, and also as throttle position (driver demand)
24Oil-pressure sensor supply +
25Oil-pressure sensor supply −
26Supply to the pressure and lock-up modulating valves
27Ignition positive
28ECU earth, common with the engine ECU
29–30CAN high and CAN low
31Multifunction switch S2
32Multifunction switch S3
33Multifunction switch S4
34Park/Neutral contact
36“1” button
37Multifunction switch S1
38–39A second CAN high and CAN low pair is also listed
40Snow button
41Normal/Sport button
42Electronic earth for the multifunction switch
43Stop-lamp contact (closing contact)
45Turbine-speed sensor +
46Turbine-speed sensor −
47Output-speed sensor −
48Output-speed sensor +
49Engine speed (TDC)
51Listed as the double-track throttle-potentiometer negative supply, and also as unused
52Throttle-potentiometer positive supply, double-track version
53Oil-temperature probe −
54Oil-temperature probe +
55Line-pressure signal
56Listed as the throttle-potentiometer signal, and also as battery positive

On the gearbox, a blue 3-pin plug is the heat-exchanger bypass solenoid, a yellow 3-pin plug is the input-speed sensor, a green 3-pin plug is the oil-pressure sensor, a yellow 12-pin plug is the hydraulic block and oil temperature, and a green 12-pin plug is the multifunction switch.

Oil level and the oil counter

New units are filled. The grade and the total capacity follow the car. The level check is not part of pre-delivery or the first service. The transmission must be out of a downgraded mode, and the car must be level.

Remove the filler plug and add 0.5 litre at the start of every check. Hold the brake and pass through every gear. With the lever in P, the engine idling and the oil at 60 °C, remove the level plug. The level is correct when oil streams and then drips. If it only drips, or does not flow, refit the plug, stop the engine, add another 0.5 litre and repeat. Filler and level plugs tighten to 2.4 m·daN (24 N·m). Too much oil heats and leaks. Too little oil damages the unit.

A later workshop method checks the level only with the drain plug removed, and drains by unscrewing the overflow tube with an Allen key. The plug evolution includes a sealing washer. The method follows the casing on the car: some casings have a separate level plug, and the later check is the overflow tube inside the drain plug.

The ECU counts oil age from oil temperature and the time spent hot. At the calibrated maximum the Sport and Snow lamps flash together to call for an oil change. After an oil change, or a transmission replacement, initialise the counter. If the ECU is replaced and the oil is not changed, copy the counter from the old ECU into the new one. If the old counter cannot be read, change the oil. Burnt oil means the heat exchanger is replaced with the transmission.

Download, configuration and pedal programming

The ECU adapts continuously by storing the difference between a reference and the value it measures. After a transmission, an ECU or another transmission component is replaced, the road test has to run frequent shifts through every gear and every program. That test is what rebuilds shift quality.

Downloading the transmission ECU is always paired with downloading the engine ECU. The download is followed by pedal programming, configuration and the road test. A new or freshly downloaded ECU is configured for the three options the car actually has: shift-lock, air conditioning, and EOBD (L4). Configuring them stops the diagnostics looking for hardware that is not fitted.

Pedal programming is required after ECU replacement, transmission replacement, a download, accelerator-cable replacement or adjustment, engine-ECU replacement or download, throttle-potentiometer replacement, and diesel injection-pump replacement. After cable work, the kick-down switch is checked as well. Cars with a motorised throttle use the throttle-housing procedure instead of this pedal routine.

WorkWhat follows it
TransmissionAdjust the multifunction switch, initialise the oil counter, road test. The new unit arrives filled.
Oil changeInitialise the oil counter.
Hydraulic distributor or its valvesAdjust the internal control, then road test. The setting uses a screw and a shim for the internal selector.
Input-speed, output-speed or pressure sensorDo not drain. Check the level.
Oil-temperature probeThe probe is in the distributor. Drain, remove the distributor and the internal harness, adjust the internal control, check the level.
Transmission ECUCopy the oil counter, configure, write the counter back, program the pedal, road test, and download the engine ECU.
Injection ECUProgram the pedal and download the transmission ECU.

Downgraded modes

Sport and Snow lamps flashing together mean the oil is too hot (they go out once it cools), the oil counter is at its maximum, the serial link to the instrument panel is broken, or a stored fault is present. Faults that flash the lamps include the ECU and its supply, the oil-pressure sensor, the sequence-valve supply, main-pressure regulation, the multifunction switch, the sequence valves, the pressure and lock-up modulators, the heat-exchanger valve, an unprogrammed accelerator pedal, a speed comparison that fails (input against output, input against engine, output against engine), engine speed, pedal position, and the analogue-sensor supply.

LevelTypical causeBehaviour
1Kick-down inputTransmission operation is unchanged.
2Oil temperature, engine-torque information, display, shift-lockComfort is affected. The degradation is small.
3Vehicle speed, lock-up valve, torque-reduction output, pressure sensor, sensor supply, brake switch, heat-exchanger valve, or throttle position lost together with torqueShift quality falls and functions are lost.
4Engine speed, or the input-speed sensorFunctions are lost or downgraded.
5Throttle potentiometer, engine torque, multifunction switch, analogue supply, pressure valve, main-pressure regulation, heat-exchanger valve control, or a failed speed comparisonHydraulic 3rd at the next ignition-on. If the car is in 4th, 4th is kept until that ignition cycle. This is the deferred stopping mode. Reverse-gear safety while driving is lost with the multifunction-switch fault.
6ECU failed, sequence valves or their supply, or the accelerator pedal not programmedHydraulic 3rd immediately. This is the stopping mode.

In stopping mode a shift from P to R or from N to R can bang. In hydraulic emergency mode the gear-change safety limits are dropped. A loud engagement is a reason to read the fault memory before condemning a clutch.

Faults that have a mechanical cause

A metallic rattle at low mileage, on units built from September to December 2003, comes from the paper face of the F1 brake discs. Driving the car through 3rd–4th shifts beds F1 in. The discs are not replaced for that noise.

A flare of 400 to 500 rpm on a cold 1st-to-2nd shift, with slip only when cold, is the emissions shift law. It is the calibration, and it is not cured by a clutch repair.

Judder in 4th around 45 mph is F3 cocking and dragging on its drum. F3 is used in 1st and 2nd. From 9 October 2003 a retaining clip is fitted, and the first gearbox number with it is 592185. In service the gearbox is replaced.

Internal bushes were changed because aluminium bushes wear, lose pressure, slip the clutches and bands, and put the gearbox into backup with oil that smells burnt. The change was described more than once, and the dates do not all agree. The plan that was then carried out, from gearbox serial 859620 on 12 April 2005, replaces the bushes that wear first: the input-shaft bush and the oil-pump-hub bush in bronze LF5, the primary-gear bush in aluminium A590, and the brake-3 drum bush with its bore opened by 0.2 mm. The satellite-carrier bush and the oil-pump-body bush followed later, in LF5. Aluminium remains in the box, so black or discoloured oil on its own is not proof of a failed gearbox. Burnt-smelling oil together with backup mode is the pressure-loss symptom. A six-bush kit exists for reconditioning.

The six bushes and what they do are: input shaft, alignment and clutch-pressure circuit; satellite-carrier 2 in the bell housing, alignment and lubrication; brake 3 drum, lubrication; oil-pump hub, alignment and clutch pressure; oil-pump body, alignment and lubrication; primary gear, alignment.

Difficult selection, judder or slip on C3, C5 and C8, with P0745 or P0932 or both, and with oil pressure that does not move in measurement, points at the oil-pressure sensor. Doubtful manufacture dates, read as 05xxx, are 05237–05238, 05241–05245, 05248–05251 and 05256–05257. The replacement sensor is 2529 24.

Backup with P0745 on any AL4 built before June 2005 that still has the Borg Warner pressure-modulator valves is a slow solenoid, caused by the solenoid spring. The electrovalve evolution number has to be above 05097. Below that, the valve is replaced. Borg Warner valves that are noisy when the car is stationary were a known complaint with no hardware change attached at the time.

On an Xsara HDi, a lack of power with the gearbox in backup and no warning lamp can be engine-torque incoherence in the gearbox ECU. The injection ECU has to be on data block D2 before any other check. A C3 that stores P1762, instrument-panel serial line, at pre-delivery is a software fault in reference 9657229780, version 037, edition 1701, and the fault does not apply to a multiplexed car.

Handling

The pump turns only with the engine, so the drive wheels are raised for a tow. Towing on the wheels is limited to N, with no oil added, and to 30 miles at no more than 30 mph. The car is not driven with the ignition off, and it cannot be push-started. The battery stays connected while the engine is running, and the ECU stays connected while the ignition is on. The electrics are not fed above 16 V, and a test lamp is not used on the ECU wiring. When the transmission is removed, the converter is pinned so it stays in the bell housing, and the centring pin is removed only as the unit is offered up to the engine.