Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Link standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 4

Removed text is struck through; added text is highlighted.

Link G4+ Monsoon is a programmable G4+ wire-in engine-management ECU. Earlier single A loom model; guide lists four analogue voltage inputs and two temperature inputs. Its injection channels are not available as spare switching outputs in the guide. Link G4+ Monsoon quick-start guide.

Model identification and I/O

ItemDocumented detailsECU familyG4+Outputs4 injection and 4 ignition drivesProgrammingPCLink version matched to ECU generation and firmwareConnector and loomSee the exact-model guide, including connector keys, wire-side orientation and optional functions

The manufacturer guidance and wiring identify the hardware; driver counts do not establish injector electrical compatibility or imply all multiplexed pins can be used at the same time.

Model-specific pinout and installation

The G4+ Monsoon quick-start guide provides the connector diagrams and installer I/O table. Refer to that version for numbered cavities, wire colours, supply, grounds, driver and sensor connection notes. Loom wire-side and ECU header views are identified on the diagram; do not transfer a pin number from another generation.

Software and further sources

Download software, firmware and full installation help from Link's download centre; identify the ECU generation and installed firmware before choosing a PCLink package. The legacy software list separates G5, G4X and G4+ compatibility. See also Link standalone ECUs.

34-position A connector

Link’s G4+ Monsoon quick-start guide, page 3, shows these assignments and colours when looking into the wire side of the loom connector, or into the ECU header. Numbering follows its four-row G4+ diagram. Confirm the actual loom and generation before wiring; this is not the later MonsoonX schedule.

PinFunctionWire colourA1Inj 4Brown/orangeA2Inj 3Brown/redA3Inj 2BrownA4Inj 1Brown/blackA5+14 VRedA6DI 4Red/whiteA7Shield/groundGreenA8Trigger 1BlackA9Trigger 2RedA10Ignition 4Blue/orangeA11Ignition 3Blue/redA12Ignition 2Blue/brownA13Ignition 1BlueA14Analog volt 4White/blackA15Temperature 1YellowA16Temperature 2Yellow/brownA17Analog volt 1Yellow/blueA18Auxiliary 4OrangeA19Auxiliary 3Orange/redA20Auxiliary 2Orange/brownA21Auxiliary 1Orange/blackA22Analog volt 2White/brownA23DI 3Grey/redA24Ground outGreenA25GroundBlackA26Auxiliary 6Orange/purpleA27Auxiliary 5Orange/blueA28CAN highOrange/greenA29CAN lowOrange/yellowA30DI 1Grey/blackA31DI 2Grey/brownA32+5 VRed/blueA33Analog volt 3Yellow/blackA34GroundBlack

The header is redrawn with every pin in Link G4+ Monsoon connector pinout.

Link G4+ family illustration

Link G4+ Atom shown only as a family illustration; the Monsoon model and its connectors differ. Manufacturer image: Link G4+ catalogue, reproduced with permission.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Link G4+ Monsoon

Link G4+ Monsoon is a programmable G4+ wire-in engine-management ECU. Earlier single A loom model; guide lists four analogue voltage inputs and two temperature inputs. Its injection channels are not available as spare switching outputs in the guide. Link G4+ Monsoon quick-start guide.

Model identification and I/O

ItemDocumented details
ECU familyG4+
Outputs4 injection and 4 ignition drives
ProgrammingPCLink version matched to ECU generation and firmware
Connector and loomSee the exact-model guide, including connector keys, wire-side orientation and optional functions

The manufacturer guidance and wiring identify the hardware; driver counts do not establish injector electrical compatibility or imply all multiplexed pins can be used at the same time.

Model-specific pinout and installation

The G4+ Monsoon quick-start guide provides the connector diagrams and installer I/O table. Refer to that version for numbered cavities, wire colours, supply, grounds, driver and sensor connection notes. Loom wire-side and ECU header views are identified on the diagram; do not transfer a pin number from another generation.

Software and further sources

Download software, firmware and full installation help from Link's download centre; identify the ECU generation and installed firmware before choosing a PCLink package. The legacy software list separates G5, G4X and G4+ compatibility. See also Link standalone ECUs.

34-position A connector

Link’s G4+ Monsoon quick-start guide, page 3, shows these assignments and colours when looking into the wire side of the loom connector, or into the ECU header. Numbering follows its four-row G4+ diagram. Confirm the actual loom and generation before wiring; this is not the later MonsoonX schedule.

PinFunctionWire colour
A1Inj 4Brown/orange
A2Inj 3Brown/red
A3Inj 2Brown
A4Inj 1Brown/black
A5+14 VRed
A6DI 4Red/white
A7Shield/groundGreen
A8Trigger 1Black
A9Trigger 2Red
A10Ignition 4Blue/orange
A11Ignition 3Blue/red
A12Ignition 2Blue/brown
A13Ignition 1Blue
A14Analog volt 4White/black
A15Temperature 1Yellow
A16Temperature 2Yellow/brown
A17Analog volt 1Yellow/blue
A18Auxiliary 4Orange
A19Auxiliary 3Orange/red
A20Auxiliary 2Orange/brown
A21Auxiliary 1Orange/black
A22Analog volt 2White/brown
A23DI 3Grey/red
A24Ground outGreen
A25GroundBlack
A26Auxiliary 6Orange/purple
A27Auxiliary 5Orange/blue
A28CAN highOrange/green
A29CAN lowOrange/yellow
A30DI 1Grey/black
A31DI 2Grey/brown
A32+5 VRed/blue
A33Analog volt 3Yellow/black
A34GroundBlack

The header is redrawn with every pin in Link G4+ Monsoon connector pinout.

Link G4+ family illustration

Link G4+ Atom, family illustration
Link G4+ Atom shown only as a family illustration; the Monsoon model and its connectors differ. Manufacturer image: Link G4+ catalogue, reproduced with permission.
Revision 4: Link G4+ Monsoon

Link G4+ Monsoon is a programmable G4+ wire-in engine-management ECU. Earlier single A loom model; guide lists four analogue voltage inputs and two temperature inputs. Its injection channels are not available as spare switching outputs in the guide. Link G4+ Monsoon quick-start guide.

Model identification and I/O

ItemDocumented details
ECU familyG4+
Outputs4 injection and 4 ignition drives
ProgrammingPCLink version matched to ECU generation and firmware
Connector and loomSee the exact-model guide, including connector keys, wire-side orientation and optional functions

The manufacturer guidance and wiring identify the hardware; driver counts do not establish injector electrical compatibility or imply all multiplexed pins can be used at the same time.

Model-specific pinout and installation

The G4+ Monsoon quick-start guide provides the connector diagrams and installer I/O table. Refer to that version for numbered cavities, wire colours, supply, grounds, driver and sensor connection notes. Loom wire-side and ECU header views are identified on the diagram; do not transfer a pin number from another generation.

Software and further sources

Download software, firmware and full installation help from Link's download centre; identify the ECU generation and installed firmware before choosing a PCLink package. The legacy software list separates G5, G4X and G4+ compatibility. See also Link standalone ECUs.

34-position A connector

Link’s G4+ Monsoon quick-start guide, page 3, shows these assignments and colours when looking into the wire side of the loom connector, or into the ECU header. Numbering follows its four-row G4+ diagram. Confirm the actual loom and generation before wiring; this is not the later MonsoonX schedule.

PinFunctionWire colour
A1Inj 4Brown/orange
A2Inj 3Brown/red
A3Inj 2Brown
A4Inj 1Brown/black
A5+14 VRed
A6DI 4Red/white
A7Shield/groundGreen
A8Trigger 1Black
A9Trigger 2Red
A10Ignition 4Blue/orange
A11Ignition 3Blue/red
A12Ignition 2Blue/brown
A13Ignition 1Blue
A14Analog volt 4White/black
A15Temperature 1Yellow
A16Temperature 2Yellow/brown
A17Analog volt 1Yellow/blue
A18Auxiliary 4Orange
A19Auxiliary 3Orange/red
A20Auxiliary 2Orange/brown
A21Auxiliary 1Orange/black
A22Analog volt 2White/brown
A23DI 3Grey/red
A24Ground outGreen
A25GroundBlack
A26Auxiliary 6Orange/purple
A27Auxiliary 5Orange/blue
A28CAN highOrange/green
A29CAN lowOrange/yellow
A30DI 1Grey/black
A31DI 2Grey/brown
A32+5 VRed/blue
A33Analog volt 3Yellow/black
A34GroundBlack

The header is redrawn with every pin in Link G4+ Monsoon connector pinout.

Link G4+ family illustration

Link G4+ Atom, family illustration
Link G4+ Atom shown only as a family illustration; the Monsoon model and its connectors differ. Manufacturer image: Link G4+ catalogue, reproduced with permission.