GEMS EM36: A historical GEMS ECU identity listed in GWv4 connection documentation. Manufacturer source.
Hardware and control
The manufacturer software manual names EM36 in its legacy connection settings. A GEMS forum discussion also names EM40 alongside it, but that discussion does not establish interchangeable hardware or connector functions. Identify the ECU name, version and wiring for the specific unit. GEMS model information.
GEMS systems use GWv4 configuration, with the required ECU definition and licence; software options and custom builds can differ. Record the label, hardware and firmware and confirm connected devices against the matching documentation. GWv4 manual.
Connector and wiring
The GEMS EM36 Operation Manual, © 2008, pages 110–112 gives the 36-way loom-connector schedule below. This is a third-party-hosted copy of the manufacturer's manual; use its loom-end view and wiring notes, and confirm board and calibration with GEMS. Many outputs are configurable, shared, or jumper-dependent. An engineer on GEMS' support forum separately identifies model-specific pin-assignment examples.
| Pin | Function in manual | Source notation |
|---|---|---|
| A1 | IGN1 | TOC1, TO220 |
| A2 | IGN6 / FUEL12 | TOC6, TO220 |
| A3 | FUEL8 | PW8 (PW1678) |
| A4 | Power input | ADR 07 |
| A5 | Power return | |
| A6 | Sensor return | |
| A7 | Crank | TINC IC0, ADR 12, T1 |
| A8 | Timing ground | |
| A9 | Coolant | ADR 05 |
| A10 | MAP2 | ADR 06 |
| A11 | Cam | TINC PH0, ADR 13, also T2 IC7 |
| A12 | IGN2 | TOC2, TO220 |
| B1 | IGN4 / FUEL10 | TOC4, TO220 |
| B2 | IGN5 / FUEL11 | TOC5, TO220 |
| B3 | FUEL6 | PW6 (PW1656) |
| B4 | FUEL1 | PW1 |
| B5 | FUEL5 | PW5 |
| B6 | MAP1 | LS PH3, ADR 01 |
| B7 | Power return | |
| B8 | FUEL7 | TIN PJ3, PW7, ADR 14, T3 |
| B9 | Air temperature | ADR 04 |
| B10 | Knock | 5–15 kHz, ADR 02, ADCR16 |
| B11 | OX2 | ADR 10 |
| B12 | IGN3 / FUEL9 | TOC3, TO220 |
| C1 | Sensor power | HS2 PE7, 12 V |
| C2 | FUEL4 | HB PW4 (PW1634), half-bridge |
| C3 | FUEL2 | HB PW2 (PW1612), half-bridge |
| C4 | Main relay | TOC7, also T2 |
| C5 | HS1 | PE3 |
| C6 | FUEL3 | PW3 |
| C7 | OX1 | ADR 03 |
| C8 | TPS | ADR 00 |
| C9 | Sensor power | ADR 17, 5 V |
| C10 | Timing input | TIN PH7, ADR 15, T4I |
| C11 | Alternate 12 V power | PE0, ADR 17 |
| C12 | Tachometer | LS PE2 |
Nine-way communications socket
The same manual lists optional CAN and RS-422 assignments on the nine-way D-type socket. Options depend on the ECU build and must not be assumed fitted.
| Pin | Function |
|---|---|
| 1 | CAN L (optional) |
| 2 | TX, RS-232C |
| 3 | RX, RS-232C |
| 4 | BUSB (optional RS-422) |
| 5 | Ground |
| 6 | CAN H (optional) |
| 7 | BUSZ (optional RS-422) |
| 8 | BUSY (optional RS-422) |
| 9 | BUSA (optional RS-422) |
Structured pinout
A structured pin index and redrawn diagram for the 36-way loom connector and the 9-way communications socket are in GEMS EM36 connector pinout.
Not established
The microcontroller used in the EM36 is not named in the GEMS documentation available for this page.
Further references
Sources reviewed 17 November 2026.