MaxxECU RACE — Eight-cylinder sequential ECU with eight peak-and-hold injectors, electronic throttle, knock inputs and eight thermocouple inputs. MaxxECU product information.

Model identification and capabilities
The manufacturer lists eight ignition outputs, nine low-driving auxiliary outputs, two 12 V driving outputs and four motor outputs. Built-in features include a 400 kPa MAP sensor, wideband lambda controller and two knock inputs. Up to twelve cylinders can be controlled with wasted-spark ignition, depending on configuration. Manufacturer specification; MaxxECU model comparison.
| Sequential cylinders, maximum | 8 |
|---|---|
| Injector outputs | 8 peak-and-hold |
| Ignition outputs | 8 |
| Configuration | MTune; check the release appropriate to the ECU and hardware revision |
Processor
The manufacturer product page lists an ARM Cortex-M3 main processor running at 120 MHz, with three further processors handling the trigger, injectors and knock detection (manufacturer specification). The specific microcontroller part number is not published.
Identification and installation
This is the original RACE, not GEN2 RACE. Use the model and hardware revision to select the wiring diagram; the manufacturer identifies RACE H2O as a separate water-protected version.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | GPO 5 | |
| A2 | IGN 1 | |
| A3 | IGN 2 | |
| A4 | GPO 8/TACHO | 660ohm pullup |
| B1 | GPO 6 | |
| B2 | IGN 3 | |
| B3 | IGN 4 | |
| B4 | GPO 1 | |
| C1 | GPO 7 | |
| C2 | IGN 5 | |
| C3 | IGN 6 | |
| C4 | GPO 2 | |
| D1 | WBO2 Heater- | |
| D2 | IGN 7 | |
| D3 | IGN 8 | |
| D4 | GPO 3 | |
| E1 | CAN H | |
| E2 | CAN L | |
| E3 | GND Shield | |
| E4 | GPO 4 | |
| F1 | CLT | |
| F2 | IAT | |
| F3 | WBO2 VREF | |
| F4 | WBO2 VS | |
| G1 | +5V sensor supply | (peak 0.5A, max 150mA) |
| G2 | TPS/AIN | |
| G3 | WBO2 IP | |
| G4 | WBO2 RCAL | |
| H1 | Sensor GND | |
| H2 | Trigger GND | |
| H3 | TRIGGER | |
| H4 | HOME | |
| J1 | AIN 1 (Temperature) | |
| J2 | AIN 2 (Temperature) | |
| J3 | AIN 3 (0-5V) | |
| J4 | AIN 4 (0-5V) | |
| K1 | INJ 1 | |
| K2 | INJ 2 | |
| K3 | DIN/VR 1 | |
| K4 | DIN/VR 2 | |
| L1 | INJ 8 | |
| L2 | INJ 7 | |
| L3 | INJ 6 | |
| L4 | Engine GND | |
| M1 | INJ 3 | |
| M2 | INJ 4 | |
| M3 | INJ 5 | |
| M4 | +12V ECU power supply |
RACE connector 2
From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | egt 5+ | |
| A2 | egt 6+ | |
| A3 | egt 7+ | |
| A4 | egt 8+ | |
| B1 | egt 5- | |
| B2 | egt 6- | |
| B3 | egt 7- | |
| B4 | egt 8- | |
| C1 | EGT 1 + | |
| C2 | EGT 2+ | |
| C3 | EGT 3+ | |
| C4 | EGT 4+ | |
| D1 | EGT 1- | |
| D2 | EGT 2- | |
| D3 | EGT 3- | |
| D4 | EGT 4- | |
| E1 | KNOCK GND | |
| E2 | Knock 1 | |
| E3 | knock 2 | |
| E4 | AIN 6 (0-5v) | |
| F1 | ain 7 (0-5v) | |
| F2 | ain 8(0-5V) | |
| F3 | din/vr 4 | |
| F4 | din/vr5 | |
| G1 | gpo 15(+12v) | |
| G2 | gpo 16 (+12v) | |
| G3 | ain 5 (0-5V) | |
| G4 | eNGINE GROUND | |
| H1 | mOTOR 2+ | |
| H2 | mOTOR 1- | |
| H3 | mOTOR 2- | |
| H4 | mOTOR 1+ |
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
All positions of the GEN1 connectors, including this unit's, are listed as a structured pin index in MaxxECU GEN1 connector pinout.
Software and further documents
- MaxxECU RACE: product information
- Model wiring and pinout reference
- MTune, quick-start guides and revision-specific wiring downloads
- MaxxECU family overview
Sources reviewed 17 November 2026.