MaxxECU SPORT — Six-cylinder sequential wire-in ECU with peak-and-hold injection and electronic-throttle outputs. MaxxECU product information.

Model identification and capabilities
SPORT has six peak-and-hold injector outputs, six ignition outputs, seven general ground outputs and two motor outputs. Inputs include two trigger inputs, two extra temperatures, six extra 0–5 V inputs, two digital inputs, an internal 400 kPa MAP sensor and a wideband controller for LSU 4.2/4.9. Its product page describes Bluetooth for MDash and USB for MTune. Manufacturer specification; MaxxECU model comparison.
| Sequential cylinders, maximum | 6 |
|---|---|
| Injector outputs | 6 peak-and-hold |
| Ignition outputs | 6 |
| Configuration | MTune; check the release appropriate to the ECU and hardware revision |
Processor
The manufacturer product page lists an ARM Cortex-M3 main processor running at 120 MHz (manufacturer specification). The specific microcontroller part number is not published.
Identification and installation
SPORT has different assignments from STREET and V1 on several positions of connector 1. Verify both connector columns and ECU revision; 5 V ignition signals require a suitable igniter or smart coil.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | GPO 4 | |
| A2 | IGN 1 | |
| A3 | IGN 2 | |
| A4 | GPO 8/TACHO | 660ohm pullup |
| B1 | GPO 5 | |
| B2 | IGN 3 | |
| B3 | IGN 4 | |
| B4 | GPO 1 | |
| C1 | AIN 5 (0-5V) | |
| C2 | IGN 5 | |
| C3 | IGN 6 | |
| C4 | GPO 2 | |
| D1 | WBO2 Heater- | |
| D2 | AIN 6 (0-5V) | |
| D3 | AIN 7 (0-5V) | |
| D4 | GPO 3 | |
| E1 | CAN H | |
| E2 | CAN L | |
| E3 | GND Shield | |
| E4 | AIN 8 (0-5V) | |
| F1 | CLT | |
| F2 | IAT | |
| F3 | WBO2 VREF | |
| F4 | WBO2 VS | |
| G1 | +5V sensor supply | (peak 0.5A, max 150mA) |
| G2 | TPS/AIN | |
| G3 | WBO2 IP | |
| G4 | WBO2 RCAL | |
| H1 | Sensor GND | |
| H2 | Trigger GND | |
| H3 | TRIGGER | |
| H4 | HOME | |
| J1 | AIN 1 (temperature) | |
| J2 | AIN 2 (Temperature) | |
| J3 | AIN 3 (0-5V) | |
| J4 | AIN 4 (0-5V) | |
| K1 | INJ 1 | |
| K2 | INJ 2 | |
| K3 | DIN 1 | |
| K4 | DIN 2 | |
| L1 | GPO 11/Motor 1- | |
| L2 | GPO 12/MOTOR 1+ | |
| L3 | INJ 6 | |
| L4 | Engine GND | |
| M1 | INJ 3 | |
| M2 | INJ 4 | |
| M3 | INJ 5 | |
| M4 | +12V ECU power supply |
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
All positions of the GEN1 connectors, including this unit's, are listed as a structured pin index in MaxxECU GEN1 connector pinout.
Software and further documents
- MaxxECU SPORT: product information
- Model wiring and pinout reference
- MTune, quick-start guides and revision-specific wiring downloads
- MaxxECU family overview
Sources reviewed 17 November 2026.