Removed text is struck through; added text is highlighted.
MaxxECU V1 — Discontinued first-generation MaxxECU, superseded by RACE according to the manufacturer. MaxxECU product information.
MaxxECU V1, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
V1 has eight peak-and-hold injector outputs and eight ignition outputs, supporting up to eight sequential cylinders or twelve with wasted spark. The manufacturer lists eight EGT inputs, built-in wideband and a 400 kPa MAP sensor. Rev 6 raised injector output capability; Rev 7 added logging and digital-input changes; Rev 9 added LSU 4.9 support. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum8Injector outputs8 peak-and-holdIgnition outputs8ConfigurationMTune; check the release appropriate to the ECU and hardware revision
Processor
The manufacturer product page lists an ARM Cortex-M3 main processor running at 120 MHz, with three further processors handling the triggers, injectors and EGT (manufacturer specification). The specific microcontroller part number is not published.
Identification and installation
The V1 wiring archive includes separate REV5+ and REV9+ documents. Identify the actual hardware revision before choosing a connector diagram or wideband sensor; do not assume a RACE replacement has identical wiring.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
All positions of the GEN1 connectors, including this unit's, are listed as a structured pin index in MaxxECU GEN1 connector pinout.
Software and further documents
MaxxECU V1: product informationModel wiring and pinout referenceMTune, quick-start guides and revision-specific wiring downloadsMaxxECU family overview
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: MaxxECU V1
MaxxECU V1 — Discontinued first-generation MaxxECU, superseded by RACE according to the manufacturer. MaxxECU product information.
MaxxECU V1, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
V1 has eight peak-and-hold injector outputs and eight ignition outputs, supporting up to eight sequential cylinders or twelve with wasted spark. The manufacturer lists eight EGT inputs, built-in wideband and a 400 kPa MAP sensor. Rev 6 raised injector output capability; Rev 7 added logging and digital-input changes; Rev 9 added LSU 4.9 support. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum
8
Injector outputs
8 peak-and-hold
Ignition outputs
8
Configuration
MTune; check the release appropriate to the ECU and hardware revision
Processor
The manufacturer product page lists an ARM Cortex-M3 main processor running at 120 MHz, with three further processors handling the triggers, injectors and EGT (manufacturer specification). The specific microcontroller part number is not published.
Identification and installation
The V1 wiring archive includes separate REV5+ and REV9+ documents. Identify the actual hardware revision before choosing a connector diagram or wideband sensor; do not assume a RACE replacement has identical wiring.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.
Position
Manufacturer function
Notes
A1
GPO 5
A2
IGN 1
A3
IGN 2
A4
GPO 8/TACHO
660ohm pullup
B1
GPO 6
B2
IGN 3
B3
IGN 4
B4
GPO 1
C1
GPO 7
C2
IGN 5
C3
IGN 6
C4
GPO 2
D1
WBO2 Heater-
D2
IGN 7
D3
IGN 8
D4
GPO 3
E1
CAN H
E2
CAN L
E3
GND Shield
E4
GPO 4
F1
CLT
F2
IAT
F3
WBO2 VREF
F4
WBO2 VS
G1
+5V sensor supply
(peak 0.5A, max 150mA)
G2
TPS/AIN
G3
WBO2 IP
G4
WBO2 RCAL
H1
Sensor GND
H2
Trigger GND
H3
TRIGGER
H4
HOME
J1
AIN 1 (Temperature)
J2
AIN 2 (Temperature)
J3
AIN 3 (0-5V)
J4
AIN 4 (0-5V)
K1
INJ 1
K2
INJ 2
K3
DIN/VR 1
K4
DIN/VR 2
L1
INJ 8
L2
INJ 7
L3
INJ 6
L4
Engine GND
M1
INJ 3
M2
INJ 4
M3
INJ 5
M4
+12V ECU power supply
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
All positions of the GEN1 connectors, including this unit's, are listed as a structured pin index in MaxxECU GEN1 connector pinout.
MaxxECU V1 — Discontinued first-generation MaxxECU, superseded by RACE according to the manufacturer. MaxxECU product information.
MaxxECU V1, manufacturer product image: MaxxECU. Used with permission.
Model identification and capabilities
V1 has eight peak-and-hold injector outputs and eight ignition outputs, supporting up to eight sequential cylinders or twelve with wasted spark. The manufacturer lists eight EGT inputs, built-in wideband and a 400 kPa MAP sensor. Rev 6 raised injector output capability; Rev 7 added logging and digital-input changes; Rev 9 added LSU 4.9 support. Manufacturer specification; MaxxECU model comparison.
Sequential cylinders, maximum
8
Injector outputs
8 peak-and-hold
Ignition outputs
8
Configuration
MTune; check the release appropriate to the ECU and hardware revision
Processor
The manufacturer product page lists an ARM Cortex-M3 main processor running at 120 MHz, with three further processors handling the triggers, injectors and EGT (manufacturer specification). The specific microcontroller part number is not published.
Identification and installation
The V1 wiring archive includes separate REV5+ and REV9+ documents. Identify the actual hardware revision before choosing a connector diagram or wideband sensor; do not assume a RACE replacement has identical wiring.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Complete 48-way connector 1 positions from the manufacturer’s model-specific column. A dash in the source is shown as not assigned. Consult the drawing for orientation and the remaining connectors. Exact wiring and connector reference.
Position
Manufacturer function
Notes
A1
GPO 5
A2
IGN 1
A3
IGN 2
A4
GPO 8/TACHO
660ohm pullup
B1
GPO 6
B2
IGN 3
B3
IGN 4
B4
GPO 1
C1
GPO 7
C2
IGN 5
C3
IGN 6
C4
GPO 2
D1
WBO2 Heater-
D2
IGN 7
D3
IGN 8
D4
GPO 3
E1
CAN H
E2
CAN L
E3
GND Shield
E4
GPO 4
F1
CLT
F2
IAT
F3
WBO2 VREF
F4
WBO2 VS
G1
+5V sensor supply
(peak 0.5A, max 150mA)
G2
TPS/AIN
G3
WBO2 IP
G4
WBO2 RCAL
H1
Sensor GND
H2
Trigger GND
H3
TRIGGER
H4
HOME
J1
AIN 1 (Temperature)
J2
AIN 2 (Temperature)
J3
AIN 3 (0-5V)
J4
AIN 4 (0-5V)
K1
INJ 1
K2
INJ 2
K3
DIN/VR 1
K4
DIN/VR 2
L1
INJ 8
L2
INJ 7
L3
INJ 6
L4
Engine GND
M1
INJ 3
M2
INJ 4
M3
INJ 5
M4
+12V ECU power supply
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
All positions of the GEN1 connectors, including this unit's, are listed as a structured pin index in MaxxECU GEN1 connector pinout.