Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Emerald M3DK
Applies to
Emerald M3DK
Tool groups
None
Manufacturers
Emerald

Connector pinout

The Emerald M3DK (produced 2001 to 2007) uses a single 36-way ECU connector. The Emerald M3DK manual v5 draws it on page 52 as a rear view: pins 25 to 36 along the top row, 24 to 13 along the offset middle row and 1 to 12 along the bottom row. The pin-out table on page 53 gives every pin's function; all 36 are listed here as manufacturer documentation.

Supplies are the ignition sense input on pin 11 and the +12 V ignition supply on pin 28 (from the main relay or common with pin 11), with the ECU earth on pin 29 (direct to battery) and the common sensor earth on pin 30. Pin 4 drives the main relay that powers the injectors and coils. Injector drivers 1 to 4 are on pins 24, 23, 26 and 1; ignition driver 1 is pin 25 and ignition driver 2 (distributorless ignition only) pin 5, both to the coil negative terminal. The main trigger input is pin 31 with its sensor earth on pin 32, and the cam phase or custom input pin 15. Throttle position signal and 5 V supply are on pins 8 and 9, air and coolant temperature on pins 16 and 33, and the oxygen sensor on pins 7 and 18 with a heater relay driver on pin 36. The idle valve uses four channels on pins 3, 2, 22 and 27. Apart from the tacho output (pin 12), all driver outputs are switched earths.

Many M3DK units were upgraded to K3 specification and some carry bespoke software, so the actual unit and its configuration must be confirmed before wiring.

Emerald M3DK 36-way ECU connector, rear view
Emerald M3DK 36-way ECU connector, rear view. Diagram redrawn by Tuning Wiki from the Emerald M3DK manual v5.

Sources

  • Emerald M3DK Manual v5, Emerald M3D; pages 52 (36-way ECU connector) and 53 (pin table). Manufacturer documentation. Accessed 19 November 2026.

Connector pinout

Applicability

Emerald M3DK (produced 2001-2007). 36-way ECU connector; functions from the Emerald M3DK manual v5, page 53, and face from page 52 (rear view of connector); manufacturer documentation. Apart from the tacho output all driver outputs are switched earths. Units upgraded to K3 specification or with bespoke software may differ.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

36-way ECU connector

Redrawn connector face
View: Rear view of connector, as drawn in the manufacturer manual
36-way ECU connector — Redrawn connector face. Rear view of connector, as drawn in the manufacturer manual

Select a pin in a photograph or the index to highlight it.

36-way ECU connector — complete pin index
PinFunction / cavityConfidence / sourceNotes
Injector driver 4
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

IACV channel 2
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

IACV channel 1
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Main relay control
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Relay powers injectors & coils
Ignition driver 2
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Only used for distributorless ignition. Connect to coil negative terminal
Cooling fan relay control
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Switched earth
Oxygen sensor signal input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Throttle pot signal input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Throttle pot supply / +5v out
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

5v output, 100mA max
Aux output 1
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Custom output, switched earth
Ignition sense input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

+12v supply via ignition switch
Tacho output signal
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

12v pulsed output
Immobilisor input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

+8v out
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

+8v supply for external sensors
Cam phase or custom input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Air temperature signal input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Aux output 2
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Custom output, switched earth
Oxygen sensor signal earth
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Shift-light driver
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Switched earth
Fuel pump relay driver
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Switched earth
Purge valve / Aux output 3
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

IACV channel 3
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Injector driver 2
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Injector driver 1
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Ignition driver 1
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Connect to coil negative terminal
Injector driver 3
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

IACV channel 4
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

+12v Ignition supply
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Supply from main relay or common with pin 11
ECU earth
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Good earth (direct to battery)
Sensor earth (common earth)
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Common earth for air, coolant & throttle sensors
Main trigger signal input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Crank sensor or distributor input signal
Main trigger sensor earth
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Earth for main/cam trigger sensor
Coolant temp signal input
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Aux analogue input 1
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

0 – 5v input
Aux analogue input 2
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

0 – 5v input
Oxygen sensor heater relay driver
Cavity: Populated
Confirmed

Emerald M3DK manual v5 p.53

Switched earth