Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Haltech standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 4

Removed text is struck through; added text is highlighted.

Nexus T2 product photograph, Haltech; permission to republish confirmed by the user.

Haltech Nexus T2 is a programmable engine-management ECU in Haltech's Nexus family. Haltech lists 5 analogue voltage inputs and 2 differential engine-position inputs. The T2 has no half-bridge outputs or integrated power distribution in the comparison. Haltech universal comparison.

Identification and I/O

ItemManufacturer comparisonInjector channels6, peak-and-holdIgnition channels6Digital pulsed outputs5MAP sensor4 bar internalTuning softwareNexus Software Programmer (NSP); verify installed firmware

Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.

Pinout and wiring

Use the manufacturer wiring diagrams and select the Nexus T2 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.

Software and further information

Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.

T1/T2 main power pins

Haltech identifies A26 as the fused supply switched by the engine-control relay and A10 as ECU ground to battery negative. These positions refer to the manufacturer T1/T2 connector, not another Nexus model. See Nexus T1/T2 pinout and installation guide for the full connector diagram, trigger wiring and electrical limits.

The full 34-pin assignment of connector A, shared by the Nexus T2 and T1 and redrawn from Haltech's wiring diagram revision 2.0 (August 2026), is in Haltech Nexus T2 and T1 connector pinout.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Haltech Nexus T2
Haltech Nexus T2 ECU
Nexus T2 product photograph, Haltech; permission to republish confirmed by the user.

Haltech Nexus T2 is a programmable engine-management ECU in Haltech's Nexus family. Haltech lists 5 analogue voltage inputs and 2 differential engine-position inputs. The T2 has no half-bridge outputs or integrated power distribution in the comparison. Haltech universal comparison.

Identification and I/O

ItemManufacturer comparison
Injector channels6, peak-and-hold
Ignition channels6
Digital pulsed outputs5
MAP sensor4 bar internal
Tuning softwareNexus Software Programmer (NSP); verify installed firmware

Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.

Pinout and wiring

Use the manufacturer wiring diagrams and select the Nexus T2 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.

Software and further information

Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.

T1/T2 main power pins

Haltech identifies A26 as the fused supply switched by the engine-control relay and A10 as ECU ground to battery negative. These positions refer to the manufacturer T1/T2 connector, not another Nexus model. See Nexus T1/T2 pinout and installation guide for the full connector diagram, trigger wiring and electrical limits.

The full 34-pin assignment of connector A, shared by the Nexus T2 and T1 and redrawn from Haltech's wiring diagram revision 2.0 (August 2026), is in Haltech Nexus T2 and T1 connector pinout.

Revision 4: Haltech Nexus T2
Haltech Nexus T2 ECU
Nexus T2 product photograph, Haltech; permission to republish confirmed by the user.

Haltech Nexus T2 is a programmable engine-management ECU in Haltech's Nexus family. Haltech lists 5 analogue voltage inputs and 2 differential engine-position inputs. The T2 has no half-bridge outputs or integrated power distribution in the comparison. Haltech universal comparison.

Identification and I/O

ItemManufacturer comparison
Injector channels6, peak-and-hold
Ignition channels6
Digital pulsed outputs5
MAP sensor4 bar internal
Tuning softwareNexus Software Programmer (NSP); verify installed firmware

Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.

Pinout and wiring

Use the manufacturer wiring diagrams and select the Nexus T2 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.

Software and further information

Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.

T1/T2 main power pins

Haltech identifies A26 as the fused supply switched by the engine-control relay and A10 as ECU ground to battery negative. These positions refer to the manufacturer T1/T2 connector, not another Nexus model. See Nexus T1/T2 pinout and installation guide for the full connector diagram, trigger wiring and electrical limits.

The full 34-pin assignment of connector A, shared by the Nexus T2 and T1 and redrawn from Haltech's wiring diagram revision 2.0 (August 2026), is in Haltech Nexus T2 and T1 connector pinout.