Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MegaSquirt and MS3Pro standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 5 to revision 5

Removed text is struck through; added text is highlighted.

MicroSquirt V3. Image: manufacturer product page; permission to republish confirmed by user.

MicroSquirt V3 is a MegaSquirt-family engine-management product. Compact MicroSquirt V3 ECU; its AMPSEAL connector is not pin-compatible with the later MS3Pro Mini despite similar physical appearance. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Wiring and pinout

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Engine-control hardware

DIYAutoTune lists two high-impedance injector outputs and two dedicated ignition outputs, plus two general-purpose outputs that can be repurposed as ignition. It has two VR-conditioned inputs and an optoisolated RPM input. Different firmware can instead use the same hardware as a transmission controller or CAN I/O device; identify the firmware before assuming an engine-control installation. MicroSquirt V3 product specification.

35-way AMPSEAL connector

Functions below follow the MicroSquirt V3 wiring guide. The V3 quick-start identifies pins 4 and 21 as VR2+ and VR2−. Do not substitute the earlier hardware's pin 21 ground assignment. See its connector view, electrical limits and related input guidance before wiring; supported assignments can depend on firmware and hardware modifications.

PinFunction in guide112 Volt Supply2CAN High3CAN Low4VRIN2+5Spare Input 26Flex Fuel7FIDLE8FUEL PUMP9INJECTOR 110INJECTOR 211IGNITION OUTPUT #212IGNITION OUTPUT #113SERIAL Rx (pre-wired)14SERIAL Tx (pre-wired)15BOOTLOADER16ACCEL LED17Warm-Up LED182ND SENSOR GROUND19SERIAL GROUND (pre-wired)20SENSOR GROUND21VR2IN-22GROUND23GROUND24MAP25CLT26IAT27TPS28Vref29Spare Input 130OPTOIN+31OPTOIN-32VRIN1+33VRIN1-34O235TACH OUTPUT

Structured pinout

The same 35-way connector, with harness colours and current ratings from the manufacturer's Microsquirt Hardware Manual (MS2/Extra 3.4.x), is tabulated and redrawn as a pin index in MicroSquirt V3 and V2 AMPSEAL connector pinout. The manual names pins 11 and 12 as Spark B and Spark A logic outputs (0.02 A) for external coil drivers, and pins 16 and 17 as spare 3 A relay outputs. Microsquirt Hardware Manual, dated 19 January 2016, accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 5: MicroSquirt V3
MicroSquirt V3
MicroSquirt V3. Image: manufacturer product page; permission to republish confirmed by user.

MicroSquirt V3 is a MegaSquirt-family engine-management product. Compact MicroSquirt V3 ECU; its AMPSEAL connector is not pin-compatible with the later MS3Pro Mini despite similar physical appearance. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Wiring and pinout

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Engine-control hardware

DIYAutoTune lists two high-impedance injector outputs and two dedicated ignition outputs, plus two general-purpose outputs that can be repurposed as ignition. It has two VR-conditioned inputs and an optoisolated RPM input. Different firmware can instead use the same hardware as a transmission controller or CAN I/O device; identify the firmware before assuming an engine-control installation. MicroSquirt V3 product specification.

35-way AMPSEAL connector

Functions below follow the MicroSquirt V3 wiring guide. The V3 quick-start identifies pins 4 and 21 as VR2+ and VR2−. Do not substitute the earlier hardware's pin 21 ground assignment. See its connector view, electrical limits and related input guidance before wiring; supported assignments can depend on firmware and hardware modifications.

PinFunction in guide
112 Volt Supply
2CAN High
3CAN Low
4VRIN2+
5Spare Input 2
6Flex Fuel
7FIDLE
8FUEL PUMP
9INJECTOR 1
10INJECTOR 2
11IGNITION OUTPUT #2
12IGNITION OUTPUT #1
13SERIAL Rx (pre-wired)
14SERIAL Tx (pre-wired)
15BOOTLOADER
16ACCEL LED
17Warm-Up LED
182ND SENSOR GROUND
19SERIAL GROUND (pre-wired)
20SENSOR GROUND
21VR2IN-
22GROUND
23GROUND
24MAP
25CLT
26IAT
27TPS
28Vref
29Spare Input 1
30OPTOIN+
31OPTOIN-
32VRIN1+
33VRIN1-
34O2
35TACH OUTPUT

Structured pinout

The same 35-way connector, with harness colours and current ratings from the manufacturer's Microsquirt Hardware Manual (MS2/Extra 3.4.x), is tabulated and redrawn as a pin index in MicroSquirt V3 and V2 AMPSEAL connector pinout. The manual names pins 11 and 12 as Spark B and Spark A logic outputs (0.02 A) for external coil drivers, and pins 16 and 17 as spare 3 A relay outputs. Microsquirt Hardware Manual, dated 19 January 2016, accessed 19 November 2026.

Revision 5: MicroSquirt V3
MicroSquirt V3
MicroSquirt V3. Image: manufacturer product page; permission to republish confirmed by user.

MicroSquirt V3 is a MegaSquirt-family engine-management product. Compact MicroSquirt V3 ECU; its AMPSEAL connector is not pin-compatible with the later MS3Pro Mini despite similar physical appearance. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Wiring and pinout

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Engine-control hardware

DIYAutoTune lists two high-impedance injector outputs and two dedicated ignition outputs, plus two general-purpose outputs that can be repurposed as ignition. It has two VR-conditioned inputs and an optoisolated RPM input. Different firmware can instead use the same hardware as a transmission controller or CAN I/O device; identify the firmware before assuming an engine-control installation. MicroSquirt V3 product specification.

35-way AMPSEAL connector

Functions below follow the MicroSquirt V3 wiring guide. The V3 quick-start identifies pins 4 and 21 as VR2+ and VR2−. Do not substitute the earlier hardware's pin 21 ground assignment. See its connector view, electrical limits and related input guidance before wiring; supported assignments can depend on firmware and hardware modifications.

PinFunction in guide
112 Volt Supply
2CAN High
3CAN Low
4VRIN2+
5Spare Input 2
6Flex Fuel
7FIDLE
8FUEL PUMP
9INJECTOR 1
10INJECTOR 2
11IGNITION OUTPUT #2
12IGNITION OUTPUT #1
13SERIAL Rx (pre-wired)
14SERIAL Tx (pre-wired)
15BOOTLOADER
16ACCEL LED
17Warm-Up LED
182ND SENSOR GROUND
19SERIAL GROUND (pre-wired)
20SENSOR GROUND
21VR2IN-
22GROUND
23GROUND
24MAP
25CLT
26IAT
27TPS
28Vref
29Spare Input 1
30OPTOIN+
31OPTOIN-
32VRIN1+
33VRIN1-
34O2
35TACH OUTPUT

Structured pinout

The same 35-way connector, with harness colours and current ratings from the manufacturer's Microsquirt Hardware Manual (MS2/Extra 3.4.x), is tabulated and redrawn as a pin index in MicroSquirt V3 and V2 AMPSEAL connector pinout. The manual names pins 11 and 12 as Spark B and Spark A logic outputs (0.02 A) for external coil drivers, and pins 16 and 17 as spare 3 A relay outputs. Microsquirt Hardware Manual, dated 19 January 2016, accessed 19 November 2026.