SCS lists Tornado 2 separately in its obsolete 2008–2015 hardware programme and identifies Delta 700 as its replacement, with a connector change required. An archived S65 installation is reported for a Tornado 2, but this example does not prove compatibility with all S65 engines or harnesses. Manufacturer or supplier evidence.
Identification, software and support
Record the complete ECU label, hardware revision, original application, connector type and current calibration. SCS identifies the older Typhoon, Tornado, Storm and Hurricane families with its final SXT Legacy software. Its newer Delta devices use the current SXTune release. The availability of calibration migration does not mean the same project should be written to different hardware without conversion. SCS software downloads · manufacturer upgrade notes.
Model-specific wiring
A third-party display interface guide identifies Tornado 2 connector A pin 21 as CAN high and pin 22 as CAN low. It links a Tornado V3 diagram; this identifies communications only and is not a full engine-harness pinout. Confirm the exact unit and get the original loom diagram. PLEX Tornado 2 connection guide.
Replacement and calibration
SCS identifies Delta 700 as the replacement for this model in its trade-in list. Consult SCS about ECU-specific connector changes, harness, software and calibration before making any conversion. See the SCS model index for the separate Delta reference.
Manufacturer connector schedules
The manufacturer’s SXTune user manual, revision 4, identifies Typhoon 2 and Tornado 2 and documents a common 35-way connector and a second 23-way Tornado connector. This archive is a copy of the Specialist Components manual. Verify the ECU label, hardware and application against the original diagrams before wiring.
Both ECU connectors are drawn as connector faces, with all 58 pins, on SC Typhoon 2 and Tornado 2 connector pinout.
35-way ECU connector
| Pin | Name | Function | Source notes |
|---|---|---|---|
| 1 | VBATT | Battery voltage direct | 6–15 V direct power |
| 2 | VKEY | Ignition key input | Switched ignition feed |
| 3 | GROUND | Power ground | — |
| 4 | INJ1 | Injector 1 | 5 A protected output |
| 5 | INJ2 | Injector 2 | 5 A protected output |
| 6 | INJ3 | Injector 3 | 5 A protected output |
| 7 | INJ4 | Injector 4 | 5 A protected output |
| 8 | DIG_GND | Crank/cam sensor ground | Digital ground |
| 9 | CRANK | Crank sensor | Hall or variable reluctance |
| 10 | CAM1 | Inlet camshaft sensor, bank 1 | Hall or variable reluctance |
| 11 | TCOOL | Coolant temperature input | 0–5 V analogue |
| 12 | TAIR | Air temperature input | 0–5 V analogue |
| 13 | IGN1 | Ignition coil 1 | Power or TTL; hardware-selected |
| 14 | IGN2 | Ignition coil 2 | Power or TTL; hardware-selected |
| 15 | IGN3 | Ignition coil 3 | Power or TTL; hardware-selected |
| 16 | IGN4 | Ignition coil 4 | Power or TTL; hardware-selected |
| 17 | LINEAR1 | Analogue input 1 | Configurable 0–5 V |
| 18 | CAM2 | Inlet camshaft sensor, bank 2 | Hall or variable reluctance |
| 19 | NTC_GND1 | Temperature sensor ground | Analogue ground |
| 20 | LAMBDA1 | Lambda sensor bank 1 | 0–5 V analogue |
| 21 | CANH | CAN high | To PC communications DB9 |
| 22 | CANL | CAN low | To PC communications DB9 |
| 23 | PROG | Program enable | To PC communications DB9 |
| 24 | RELAY1 | Relay output | Configurable function |
| 25 | RELAY2 | Fuel pump relay output | Fuel pump and O2 heater relay |
| 26 | PWM1 | PWM output 1 | Configurable; 5 A protected |
| 27 | PWM2 | PWM output 2 | Configurable; 5 A protected |
| 28 | AUX1 | Auxiliary output 1 | 5 A protected |
| 29 | AUX2 | Auxiliary output 2 | 5 A protected |
| 30 | LINEAR_GND1 | TPS and MAP ground | Analogue ground |
| 31 | NTC_1 | NTC sensor input 1 | Temperature sensor input |
| 32 | TPS1 | Throttle position sensor 1 | 0–5 V input |
| 33 | MAP | Manifold pressure sensor input | 0–5 V input |
| 34 | VREF1 | TPS and MAP reference voltage | 5 V reference |
| 35 | GROUND | Power ground | — |
23-way Tornado connector
| Pin | Name | Function | Source notes |
|---|---|---|---|
| 1 | IGN5/INJ7 | Ignition coil 5 | Power or TTL; hardware-selected |
| 2 | IGN6/INJ8 | Ignition coil 6 | Power or TTL; hardware-selected |
| 3 | AUX3 | Auxiliary output 3 | Configurable; 5 A protected |
| 4 | AUX4 | Auxiliary output 4 | Configurable; 5 A protected |
| 5 | HBRIDGE+ | DC motor positive | 5 A motor control |
| 6 | HBRIDGE− | DC motor negative | 5 A motor control |
| 7 | FANS1 | Cooling fan relay 1 | 5 A protected |
| 8 | FANS2 | Cooling fan relay 2 | 5 A protected |
| 9 | PWM3 | PWM output 3 | Configurable; 5 A protected |
| 10 | PWM4 | PWM output 4 | 5 A high-speed; shared with H-bridge |
| 11 | WSPEED1 | Left rear wheel speed | Hall input |
| 12 | WSPEED2 | Right rear wheel speed | Hall input |
| 13 | WSPEED3 | Left front wheel speed | Hall input |
| 14 | WSPEED4 | Right front wheel speed | Hall input |
| 15 | LAMBDA2 | Lambda sensor bank 2 | 0–5 V input |
| 16 | TPS2 | Analogue input | 0–5 V input |
| 17 | PPS1 | Analogue input | 0–5 V input |
| 18 | PPS2 | Analogue input | 0–5 V input |
| 19 | LINEAR5 | Analogue input 5 | 0–5 V input |
| 20 | NTC_2 | NTC sensor input 2 | 0–5 V temperature input |
| 21 | NTC_3 | NTC sensor input 3 | 0–5 V temperature input |
| 22 | SENS_GND2 | Analogue ground | Sensor ground |
| 23 | VREF2 | Voltage reference | 5 V reference |
13-way automotive harness expansion connector
The manual describes this as a connector usually provided on SC-supplied automotive looms; it is a harness connector, not the 23-way ECU connector. Individual looms can vary.
| Pin | Function |
|---|---|
| 1 | +12 V ignition feed |
| 2 | Ground |
| 3 | Lambda sensor signal input |
| 4 | Linear 1 analogue input |
| 5 | Fuel pump output, positive supply to pump |
| 6 | Relay 1 switched output |
| 7 | PWM 1 output |
| 8 | PWM 2 output |
| 9 | Auxiliary 1 output |
| 10 | Auxiliary 2 output |
| 11 | Cam 2 input |
| 12 | Reference voltage output |
| 13 | Manifold pressure sensor input |