Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MegaSquirt and MS3Pro standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

MicroSquirt Module V2.2. Image: manufacturer product page; permission to republish confirmed by user.

A compact assembled MicroSquirt-based engine-control board intended to be integrated into a custom carrier and enclosure; not a complete sealed wire-in ECU. DIYAutoTune product and support information.

Identification and wiring

Record exact model, board revision, firmware, installation and carrier before wiring. DIYAutoTune documentation index includes model-specific manuals; connector functions are not interchangeable across ECU and module designs. Confirm all power, grounds and driver ratings from the applicable manual.

See MegaSquirt and MS3Pro family. Sources reviewed 17 November 2026.

Processor and firmware

The module is a Megasquirt-2 product: the developers guide states that purchase of the module licenses any of the Megasquirt 2 firmwares on it, and documents it for MS2/Extra 3.4.x. The guide does not name the processor part number. Manufacturer documentation.

Capabilities

Electrically the module is similar to the MicroSquirt for most sensor inputs and outputs. It has two injector channels (INJ1, INJ2), low-current ignition outputs Spark A and B plus mid-current outputs usable as Spark C and D, VR and opto tach inputs, MAP, coolant, air temperature, throttle and oxygen inputs, flex fuel, CAN and serial. Unlike the MicroSquirt it uses single-ended, non-adjustable tach circuits and brings out more I/O on a secondary header, where PT6 and PT7 can drive a stepper idle valve or give four-cylinder sequential fuel. It is a universal module for custom carriers; no vehicle-specific application list applies.

Connector pinout

The J2 50-pin main header and J1 10-pin secondary header are tabulated and redrawn in MicroSquirt Module V2.2 connector pinout. Harness connector numbering depends on the carrier board.

Sources

Microsquirt-Module Developers Guide, MS2/Extra 3.4, James Murray, dated 9 July 2015. Manufacturer documentation. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: MicroSquirt Module V2.2
MicroSquirt Module V2.2
MicroSquirt Module V2.2. Image: manufacturer product page; permission to republish confirmed by user.

A compact assembled MicroSquirt-based engine-control board intended to be integrated into a custom carrier and enclosure; not a complete sealed wire-in ECU. DIYAutoTune product and support information.

Identification and wiring

Record exact model, board revision, firmware, installation and carrier before wiring. DIYAutoTune documentation index includes model-specific manuals; connector functions are not interchangeable across ECU and module designs. Confirm all power, grounds and driver ratings from the applicable manual.

See MegaSquirt and MS3Pro family. Sources reviewed 17 November 2026.

Processor and firmware

The module is a Megasquirt-2 product: the developers guide states that purchase of the module licenses any of the Megasquirt 2 firmwares on it, and documents it for MS2/Extra 3.4.x. The guide does not name the processor part number. Manufacturer documentation.

Capabilities

Electrically the module is similar to the MicroSquirt for most sensor inputs and outputs. It has two injector channels (INJ1, INJ2), low-current ignition outputs Spark A and B plus mid-current outputs usable as Spark C and D, VR and opto tach inputs, MAP, coolant, air temperature, throttle and oxygen inputs, flex fuel, CAN and serial. Unlike the MicroSquirt it uses single-ended, non-adjustable tach circuits and brings out more I/O on a secondary header, where PT6 and PT7 can drive a stepper idle valve or give four-cylinder sequential fuel. It is a universal module for custom carriers; no vehicle-specific application list applies.

Connector pinout

The J2 50-pin main header and J1 10-pin secondary header are tabulated and redrawn in MicroSquirt Module V2.2 connector pinout. Harness connector numbering depends on the carrier board.

Sources

Revision 3: MicroSquirt Module V2.2
MicroSquirt Module V2.2
MicroSquirt Module V2.2. Image: manufacturer product page; permission to republish confirmed by user.

A compact assembled MicroSquirt-based engine-control board intended to be integrated into a custom carrier and enclosure; not a complete sealed wire-in ECU. DIYAutoTune product and support information.

Identification and wiring

Record exact model, board revision, firmware, installation and carrier before wiring. DIYAutoTune documentation index includes model-specific manuals; connector functions are not interchangeable across ECU and module designs. Confirm all power, grounds and driver ratings from the applicable manual.

See MegaSquirt and MS3Pro family. Sources reviewed 17 November 2026.

Processor and firmware

The module is a Megasquirt-2 product: the developers guide states that purchase of the module licenses any of the Megasquirt 2 firmwares on it, and documents it for MS2/Extra 3.4.x. The guide does not name the processor part number. Manufacturer documentation.

Capabilities

Electrically the module is similar to the MicroSquirt for most sensor inputs and outputs. It has two injector channels (INJ1, INJ2), low-current ignition outputs Spark A and B plus mid-current outputs usable as Spark C and D, VR and opto tach inputs, MAP, coolant, air temperature, throttle and oxygen inputs, flex fuel, CAN and serial. Unlike the MicroSquirt it uses single-ended, non-adjustable tach circuits and brings out more I/O on a secondary header, where PT6 and PT7 can drive a stepper idle valve or give four-cylinder sequential fuel. It is a universal module for custom carriers; no vehicle-specific application list applies.

Connector pinout

The J2 50-pin main header and J1 10-pin secondary header are tabulated and redrawn in MicroSquirt Module V2.2 connector pinout. Harness connector numbering depends on the carrier board.

Sources