Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Link standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Link G4X WRX9X plug-in ECU
Manufacturer product image of WRX9X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X WRX9X is a vehicle-specific programmable plug-in ECU for the Subaru WRX version 7–9 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX9X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The WRX9X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Processor

Link does not name the microcontroller. Its G4X plug-in specification describes a 150 MHz specialised engine-management microprocessor with 32-bit floating-point calculation, 12-bit ADC resolution and 4 Gb of non-volatile flash (manufacturer specification).

Engine applications

The board is for the GD/GG-chassis Subaru Impreza WRX and STi, version 7 to 9, with the EJ20 turbocharged engine (EJ205 in the WRX, EJ207 in the Japanese-market STi). Dealer listings give model years from 2000 or 2001 to 2007, with ranges that vary by seller, and manual transmission only (dealer listings, not manufacturer documentation). The Link manual covers both WRX and STi wiring, selected by jumpers on the bottom board.

Connector pinout

All 122 factory header positions and the Link expansion and CAN/RS232 connectors are drawn and indexed in the Link G4X WRX9X connector pinout.

Manufacturer connector schedules

From Link's WRX9X installation manual (2025). Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Applies to the V7–9 WRX/STi layouts documented by Link. On some Australian-market vehicles pin D11 controls the alternator instead of intercooler spray; the spray is controlled separately and pin B12 is not connected. Configure the sample map for the actual vehicle.

Factory main header positions

Factory pinLink ECU channelFactory function
A-1DI 5Vehicle Speed
C-21Ignition 4Ignition
A-2Main Relay (WRX) / DI 3 (STI)Main Relay Control (WRX) / A/C Request (STI)
C-22Ignition 3Ignition
A-3DI 10Rear de-mist switch
C-23Ignition 2Ignition
A-4nc—
C-24Ignition 1Ignition
A-5Ignition Switch (STI)Controls Main Relay
A-6DI 3 (WRX) / Main Relay (STI)A/C Request (WRX) / Main Relay Control (STI)
D-1Injector 1Injection
A-7Ground—
D-2+14V Main RelayECU Power
A-8nc—
D-3+14V Main RelayECU Power
A-9nc—
D-4nc—
A-10nc—
D-5nc—
A-11nc—
D-6nc—
A-12nc—
D-7nc—
A-13nc—
D-8Ground—
A-14Ignition Switch (WRX)Controls Main Relay
D-9Ground—
A-15Ground—
D-10nc—
A-16DI 6Start Signal
D-11Injector 6 (Aux)IC Spray Relay*
A-17nc—
D-12nc—
A-18nc—
D-13nc—
A-19nc—
D-14An Temp 3IAT (Spec C)
A-20nc—
D-15Aux 5CE Light
A-21nc—
D-16nc—
A-22Ground—
D-17Injector 5 (Aux)Engine Fan
D-18Ground (O2 Shield)—
B-1Trig 2Trig 2
D-19nc—
B-2Trig 1Trig 1
D-20nc—
B-3nc—
D-21nc—
B-4Knock 1Knock
D-22nc—
B-5nc—
D-23nc—
B-6nc—
D-24Aux 6Boost Solenoid
B-7An Volt 3TPS (Main)
D-25nc—
B-8An Volt 1MAP Sensor
D-26nc—
B-9+5V Out—
D-27Injector 7 (Aux)A/C Clutch Relay
B-10Ground (Trig 2)—
D-28Injector 8 (Aux)A/C Fan Relay
B-11Ground (Trig 1)—
D-29nc—
B-12DI 4IC Spray Switch
D-30nc—
B-13nc—
D-31nc—
B-14nc—
B-15nc—
E-1Ground—
B-16nc—
E-2DI 2Bank 1 Inl Cam Pos
B-17An Volt 4Rear O2 Signal
E-3Ground (Cam Pos)—
B-18An Temp 2ECT
E-4+14V Out (TGV)—
B-19Ground (Signal)—
E-5Ground (TGV)—
B-20nc—
E-6+14V Out (Cam)—
B-21Ground (Shield)—
E-7Ground (AFM)—
B-22Ground (Shield)—
E-8Ground (AFM Shield)—
B-23nc—
E-9DI 1Bank 2 Inl Cam Pos
B-24An Volt 5Power Steer Switch
E-10+14V Out (TGV)—
B-25nc—
E-11Ground (TGV)—
B-26Ground (Shield)—
E-12Aux 2Bank 1 Inl AVCS Sol
B-27An Temp 1IAT (AFM)
E-13An Volt 2AFM Signal
B-28nc—
E-14Ground (Cam Shield)—
E-15Ground (Cam Pos)—
C-1nc—
E-16Aux 1Bank 2 Inl AVCS Sol
C-2nc—
E-17+14V Out (Cam)—
C-3nc—
C-4Injector 4Injection
C-5Injector 3Injection
C-6Injector 2Injection
C-7nc—
C-8Ground—
C-9Ignition 5 (Aux)Tacho
C-10Aux 3ISC Solenoid
C-11nc—
C-12nc—
C-13Aux 8Rear O2 Heater
C-14nc—
C-15Aux 7FP Speed Control
C-16Aux 7FP Speed Control
C-17Ground—
C-18Ground—
C-19nc—
C-20nc—

Expansion connector

PinLink ECU channelFactory function
1Ignition 6 (Aux)—
2Ignition 7 (Aux)—
3Ignition 8 (Aux)—
4DI 7—
5DI 8—
6DI 9—
7An temp 4—
8An Volt 11—
9Ground (Signal)—
10+5V Out—
11Aux 9—
12Aux 10—
13An Volt 6—
14An Volt 7—
15An Volt 9—
16An Volt 10—

CAN 1/RS232 Connector

PinFunctionWire colour
1Comms GNDBrown
2CAN1 LGreen
3CAN1 HWhite
4RS232-RXGrey
5RS232-TXYellow

CAN 2/OBD Connector

PinFunctionWire colour
1GNDBrown
2CAN2 LGreen
3CAN2 HWhite
4NCGrey
5+14VYellow

Sources