Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Motorsport Electronics ME360
Applies to
Motorsport Electronics ME360, Motorsport Electronics ME221, Motorsport Electronics ME442
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Connector

The Motorsport Electronics GEN2 wire-in range (ME221, ME360 and ME442) uses a single sealed 90-way FCI main connector with a common pinout. According to the manufacturer, the three models share the pin assignments but not every channel: the ME221 GEN2 is aimed at four-cylinder engines, the ME360 GEN2 at six-cylinder and complex four-cylinder engines (for example with drive-by-wire), and the ME442 GEN2 is the fully featured eight-cylinder unit with every channel populated. Header crimps are listed as part number 211CC2S1160P.

Pin assignments

All 90 pins are listed with the manufacturer's function and notes, and each pin records which models provide it. Channels common to all three include coils 1 to 4, injectors 1 to 4, low-side outputs 1 to 6, the LSU 4.9 wideband interface (pins 15, 16, 19, 20, 49 and 50), CAN 1 (high pin 21, low pin 51), USB, RS232 serial, crank VR (80/81), cam A VR (22/23), knock 1, stepper outputs, tachometer and analogue/temperature inputs. Switched 12 V supply is on pins 14 and 64, power grounds on 10, 61, 89 and 90, and sensor grounds on 52 and 84; the manufacturer directs all sensors to return to pin 52. The ME360 adds coils 5 and 6, injectors 5 and 6, the drive-by-wire H-bridge (65/66), cam B VR (82/83), EGT 1, extra digital inputs and relay drivers. Coils 7 and 8, injectors 7 and 8, knock 2 and several analogue inputs are ME442-only. Pin 85 is not used.

The manufacturer documentation does not show the face of the 90-way header, so the drawing is a numbered pin index rather than a connector view. Assignments are manufacturer documentation (graded confirmed). The table does not apply to GEN1 wire-in units (ME221/ME100 GEN1 28-way, ME442 REV C/D) or to vehicle-specific plug-in boards. Confirm the unit's generation, model and firmware configuration before wiring.

Diagram redrawn by Tuning Wiki from the Motorsport Electronics GEN2 wire-in pinout. See the ME221, ME360 and ME442 hubs.

Sources

Motorsport Electronics, ME442/ME360/ME221 GEN2 Wire-In Pinout, online manual, with ME221 and ME360 availability columns. Manufacturer documentation. Accessed 19 November 2026.Motorsport Electronics Limited, ME221/360/442 GEN2 90-Way Quick Install Guide (PDF), introduction, connector, grounds and Appendix A (ME442 GEN2 has every channel). Manufacturer documentation. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Motorsport Electronics ME221, ME360 and ME442 GEN2 90-way connector pinout

Connector

The Motorsport Electronics GEN2 wire-in range (ME221, ME360 and ME442) uses a single sealed 90-way FCI main connector with a common pinout. According to the manufacturer, the three models share the pin assignments but not every channel: the ME221 GEN2 is aimed at four-cylinder engines, the ME360 GEN2 at six-cylinder and complex four-cylinder engines (for example with drive-by-wire), and the ME442 GEN2 is the fully featured eight-cylinder unit with every channel populated. Header crimps are listed as part number 211CC2S1160P.

Pin assignments

All 90 pins are listed with the manufacturer's function and notes, and each pin records which models provide it. Channels common to all three include coils 1 to 4, injectors 1 to 4, low-side outputs 1 to 6, the LSU 4.9 wideband interface (pins 15, 16, 19, 20, 49 and 50), CAN 1 (high pin 21, low pin 51), USB, RS232 serial, crank VR (80/81), cam A VR (22/23), knock 1, stepper outputs, tachometer and analogue/temperature inputs. Switched 12 V supply is on pins 14 and 64, power grounds on 10, 61, 89 and 90, and sensor grounds on 52 and 84; the manufacturer directs all sensors to return to pin 52. The ME360 adds coils 5 and 6, injectors 5 and 6, the drive-by-wire H-bridge (65/66), cam B VR (82/83), EGT 1, extra digital inputs and relay drivers. Coils 7 and 8, injectors 7 and 8, knock 2 and several analogue inputs are ME442-only. Pin 85 is not used.

The manufacturer documentation does not show the face of the 90-way header, so the drawing is a numbered pin index rather than a connector view. Assignments are manufacturer documentation (graded confirmed). The table does not apply to GEN1 wire-in units (ME221/ME100 GEN1 28-way, ME442 REV C/D) or to vehicle-specific plug-in boards. Confirm the unit's generation, model and firmware configuration before wiring.

Diagram redrawn by Tuning Wiki from the Motorsport Electronics GEN2 wire-in pinout. See the ME221, ME360 and ME442 hubs.

Sources

Connector pinout

Applicability

Motorsport Electronics ME221, ME360 and ME442 GEN2 wire-in ECUs (common 90-way FCI header). Functions and per-model availability from the manufacturer GEN2 wire-in pinout; ME442 GEN2 has every channel. Not applicable to GEN1 wire-in units (ME221 GEN1 28-way, ME442 REV C/D) or to vehicle-specific plug-in boards. Drawing is a numerical pin index; the header face layout is not published.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

GEN2 main connector (90-way FCI)

Pin index (numerical order)
View: Pin index; connector face layout not shown in source
GEN2 main connector (90-way FCI) — Pin index (numerical order). Pin index; connector face layout not shown in source

Select a pin in a photograph or the index to highlight it.

GEN2 main connector (90-way FCI) — complete pin index
PinFunction / cavityConfidence / sourceNotes
COIL 4 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
COIL 3 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 4 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 2 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 4 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
DIG_IN 1 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 2 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 3 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
LOW SIDE RELAY 18 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
GROUND CHASSIS (GROUNDS (CHASSIS))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
EGT 1
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
LOW SIDE 2 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 15 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
VBAT IGNITION (VOLTAGE SUPPLY (SWITCHED 12V IGNITION) Linked internally to Pin 15 below.)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU HEATER +VE (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU HEATER -VE (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 3 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 4 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU UN (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU VM (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAN 1 HIGH
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAM A VR+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAM A VR-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
SERIAL 1 GROUND (SERIAL COMMS GROUND)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
SERIAL 1 TX (SERIAL COMMS TRANSMIT RS232 LEVEL)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 1 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 8 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
INJECTOR 5 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
COIL 7 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
COIL 8 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
COIL 2 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
COIL 1 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 3 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 6 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
USB D+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
USB D-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 11 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
USB VBUS
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 6 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 17 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
USB GROUND
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 12 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 14 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 4 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
5V REF (200mA MAX 5V SENSOR SUPPLY)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
5V REF (200mA MAX 5V SENSOR SUPPLY)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA TEMP 4 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
ANA VOLT 7 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
LSU IA (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU IP (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAN 1 LOW
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
SENSORS GROUND (SENSOR & COMMS GROUND AND VR SHEILDS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
KNOCK 1 SIGNAL (KNOCK DSP 1)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
KNOCK 2 SIGNAL (KNOCK DSP 2)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
SERIAL 1 RX (SERIAL COMMS RECIEVE RS232 LEVEL)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 2 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA TEMP 2 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 6 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
COIL 5 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
COIL 6 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
GROUND (POWER GROUND TO CHASSIS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 5 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
INJECTOR 1 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
VBAT (BATTERY VOLTAGE SUPPLY (SWITCHED IGNITION))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
H-BRIDGE A OUT 1 (DBW H-BRIDGE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
H-BRIDGE A OUT 2 (DBW H-BRIDGE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
Stepper 1 / A1 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Stepper 2 / A2 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 5 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Stepper 3 / B1 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Stepper 4 / B2 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 13 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 1 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 3 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 16 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
5V REF (250mA MAX 5V SENSOR SUPPLY)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA TEMP 3 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
ANA VOLT 6 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
TACHOMETER (200mA 12V PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CRANK VR+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CRANK VR-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAM B VR+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
CAM B VR-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
Sensor Ground (Use for Crank Sensor Shields (Typically))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Not used
Cavity: Unused
Confirmed

ME GEN2 wire-in pinout (online manual)

ANA TEMP 1 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 5 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
INJECTOR 7 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
GROUND (POWER GROUND TO CHASSIS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
GROUND (POWER GROUND TO CHASSIS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Revision 1: Motorsport Electronics ME221, ME360 and ME442 GEN2 90-way connector pinout

Connector

The Motorsport Electronics GEN2 wire-in range (ME221, ME360 and ME442) uses a single sealed 90-way FCI main connector with a common pinout. According to the manufacturer, the three models share the pin assignments but not every channel: the ME221 GEN2 is aimed at four-cylinder engines, the ME360 GEN2 at six-cylinder and complex four-cylinder engines (for example with drive-by-wire), and the ME442 GEN2 is the fully featured eight-cylinder unit with every channel populated. Header crimps are listed as part number 211CC2S1160P.

Pin assignments

All 90 pins are listed with the manufacturer's function and notes, and each pin records which models provide it. Channels common to all three include coils 1 to 4, injectors 1 to 4, low-side outputs 1 to 6, the LSU 4.9 wideband interface (pins 15, 16, 19, 20, 49 and 50), CAN 1 (high pin 21, low pin 51), USB, RS232 serial, crank VR (80/81), cam A VR (22/23), knock 1, stepper outputs, tachometer and analogue/temperature inputs. Switched 12 V supply is on pins 14 and 64, power grounds on 10, 61, 89 and 90, and sensor grounds on 52 and 84; the manufacturer directs all sensors to return to pin 52. The ME360 adds coils 5 and 6, injectors 5 and 6, the drive-by-wire H-bridge (65/66), cam B VR (82/83), EGT 1, extra digital inputs and relay drivers. Coils 7 and 8, injectors 7 and 8, knock 2 and several analogue inputs are ME442-only. Pin 85 is not used.

The manufacturer documentation does not show the face of the 90-way header, so the drawing is a numbered pin index rather than a connector view. Assignments are manufacturer documentation (graded confirmed). The table does not apply to GEN1 wire-in units (ME221/ME100 GEN1 28-way, ME442 REV C/D) or to vehicle-specific plug-in boards. Confirm the unit's generation, model and firmware configuration before wiring.

Diagram redrawn by Tuning Wiki from the Motorsport Electronics GEN2 wire-in pinout. See the ME221, ME360 and ME442 hubs.

Sources

Connector pinout

Applicability

Motorsport Electronics ME221, ME360 and ME442 GEN2 wire-in ECUs (common 90-way FCI header). Functions and per-model availability from the manufacturer GEN2 wire-in pinout; ME442 GEN2 has every channel. Not applicable to GEN1 wire-in units (ME221 GEN1 28-way, ME442 REV C/D) or to vehicle-specific plug-in boards. Drawing is a numerical pin index; the header face layout is not published.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

GEN2 main connector (90-way FCI)

Pin index (numerical order)
View: Pin index; connector face layout not shown in source
GEN2 main connector (90-way FCI) — Pin index (numerical order). Pin index; connector face layout not shown in source

Select a pin in a photograph or the index to highlight it.

GEN2 main connector (90-way FCI) — complete pin index
PinFunction / cavityConfidence / sourceNotes
COIL 4 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
COIL 3 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 4 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 2 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 4 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
DIG_IN 1 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 2 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 3 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
LOW SIDE RELAY 18 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
GROUND CHASSIS (GROUNDS (CHASSIS))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
EGT 1
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
LOW SIDE 2 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 15 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
VBAT IGNITION (VOLTAGE SUPPLY (SWITCHED 12V IGNITION) Linked internally to Pin 15 below.)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU HEATER +VE (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU HEATER -VE (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 3 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 4 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU UN (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU VM (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAN 1 HIGH
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAM A VR+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAM A VR-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
SERIAL 1 GROUND (SERIAL COMMS GROUND)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
SERIAL 1 TX (SERIAL COMMS TRANSMIT RS232 LEVEL)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 1 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 8 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
INJECTOR 5 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
COIL 7 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
COIL 8 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
COIL 2 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
COIL 1 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 3 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 6 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
USB D+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
USB D-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 11 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
USB VBUS
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 6 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 17 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
USB GROUND
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 12 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 14 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 4 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
5V REF (200mA MAX 5V SENSOR SUPPLY)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
5V REF (200mA MAX 5V SENSOR SUPPLY)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA TEMP 4 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
ANA VOLT 7 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
LSU IA (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LSU IP (Wideband Connection (LSU4.9))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAN 1 LOW
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
SENSORS GROUND (SENSOR & COMMS GROUND AND VR SHEILDS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
KNOCK 1 SIGNAL (KNOCK DSP 1)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
KNOCK 2 SIGNAL (KNOCK DSP 2)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
SERIAL 1 RX (SERIAL COMMS RECIEVE RS232 LEVEL)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 2 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA TEMP 2 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
INJECTOR 6 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
COIL 5 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
COIL 6 (IGBT or 5V TTL (Software Selectable))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
GROUND (POWER GROUND TO CHASSIS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
DIG_IN 5 (PULLED HIGH WEAK 5V)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
INJECTOR 1 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
VBAT (BATTERY VOLTAGE SUPPLY (SWITCHED IGNITION))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
H-BRIDGE A OUT 1 (DBW H-BRIDGE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
H-BRIDGE A OUT 2 (DBW H-BRIDGE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
Stepper 1 / A1 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Stepper 2 / A2 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 5 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Stepper 3 / B1 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Stepper 4 / B2 (500mA H-Bridge)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 13 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 1 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE 3 (2.5A PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
LOW SIDE RELAY 16 (100mA Relay Driver)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
5V REF (250mA MAX 5V SENSOR SUPPLY)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA TEMP 3 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
ANA VOLT 6 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
TACHOMETER (200mA 12V PWM-ABLE)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CRANK VR+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CRANK VR-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
CAM B VR+
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
CAM B VR-
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME360 and ME442 GEN2 only; not available on ME221 GEN2.
Sensor Ground (Use for Crank Sensor Shields (Typically))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
Not used
Cavity: Unused
Confirmed

ME GEN2 wire-in pinout (online manual)

ANA TEMP 1 (THERMISTOR INPUT PULLED TO 5V via 2K7)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
ANA VOLT 5 (0-5V ANALOG PROTECTED INPUT)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
INJECTOR 7 (2A CONSTANT PROTECTED (6ohm Min Hi Imp))
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

ME442 GEN2 only; not available on ME221 or ME360 GEN2.
GROUND (POWER GROUND TO CHASSIS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.
GROUND (POWER GROUND TO CHASSIS)
Cavity: Populated
Confirmed

ME GEN2 wire-in pinout (online manual)

Available on ME221, ME360 and ME442 GEN2.