Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Haltech E6H
Applies to
Haltech E6H, Haltech E6M
Tool groups
None
Manufacturers
Haltech

J1 ECU main connector

The Haltech E6H and E6M share one main wiring harness, drawn by Haltech as the "E6H/M main harness" (revision A, 12 December 2000); Haltech's archive lists the same drawing and the same manual for both units. The ECU plugs into the harness through J1, a 36-pin Packard connector (housing 1211 0490, terminals 1208 4912). The harness then branches to separate connectors for the trigger, injectors, idle speed motor, sensors, ignition output, fuse block and relays.

Of the 36 pins, 32 are used and four (3, 4, 23 and 24) are not connected. The used pins carry the four injector drivers (19 to 22), four idle-motor outputs (14 to 17), the ignition output (36), the main trigger and home inputs (6, 13), the MAP, air temperature, coolant, throttle position and oxygen sensor inputs with a 5 V supply, road speed, a trim input and a spare analogue input, two digital outputs, an auxiliary input and output, the fuel pump relay drive, the RS-232 TX and RX lines, the +13 V ECU supply (25) and two grounds (26, 32). Pins 7 and 12 (INPUT B and INPUT A) are the reluctor inputs used by the onboard reluctor adaptor of the E6M; the E6H has no onboard adaptor. Harness wire colours from the drawing are listed in the pin notes.

The diagram is a pin index in the order Haltech lists the pins; the physical connector face and viewing side are not shown in the source. The E6H-8 and E6M-8, which drive more injectors, are covered by the same manual but are not drawn separately.

Haltech E6H and E6M J1 ECU main connector pin index
Haltech E6H / E6M J1 pin index, redrawn by Tuning Wiki from Haltech's E6H/M main harness drawing.

Sources

  • E6H/M main harness electrical drawing, Haltech, revision A, 12 December 2000 (listed as both "E6H Wiring Harness" and "E6M Wiring Harness" in the discontinued wiring-diagram archive). Manufacturer documentation. Accessed 19 November 2026.
  • Haltech E6H/E6M instruction manual, print version 1.0a, 16 April 2004 (trigger connector pin table and model differences). Manufacturer documentation. Accessed 19 November 2026.

Connector pinout

Applicability

Haltech E6H and E6M (the harness drawing is titled 'E6H/M main harness'; the E6H/E6M manual covers E6H, E6M, E6H-8 and E6M-8). J1 is the 36-pin ECU main connector of the flying-lead main harness (Packard 1211 0490 housing, 1208 4912 terminals). Pin functions and harness wire colours are as printed on the drawing; pins marked NC are not connected. INPUT A and INPUT B are the reluctor inputs used only by the E6M's onboard reluctor adaptor. The E6H-8 and E6M-8 are not separately drawn. The diagram is a pin index; the physical connector face and viewing side are not shown in the source.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

J1 - ECU main connector (36 pins)

Redrawn pin index
View: Pin index as listed on the Haltech harness drawing; connector face layout and viewing side not shown in source
J1 - ECU main connector (36 pins) — Redrawn pin index. Pin index as listed on the Haltech harness drawing; connector face layout and viewing side not shown in source

Select a pin in a photograph or the index to highlight it.

J1 - ECU main connector (36 pins) — complete pin index
PinFunction / cavityConfidence / sourceNotes
SPARE A/D
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour RED/BLK.
O2 SENSOR
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRY (shielded).
Not connected (N/C)
Cavity: Unused
Confirmed

Haltech E6H/M main harness drawing, rev A

Not connected (N/C)
Cavity: Unused
Confirmed

Haltech E6H/M main harness drawing, rev A

ROAD SPEED
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRY/YEL (shielded).
TRIGGER
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour YEL (shielded).
INPUT B
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour RED (shielded). Reluctor input on E6M only (trigger connector pin D).
TX
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour RED (shielded).
RX
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLU (shielded).
TRIM
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLK/WHT.
MAP
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour YEL.
INPUT A
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLU (shielded). Reluctor input on E6M only (trigger connector pin C).
HOME
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRN (shielded).
IDL4
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BRN/WHT.
IDL3
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour YEL/RED.
IDL2
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRN/YEL.
IDL1
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BRN.
+5VDC
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour ORG.
INJ1
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour L. BLU.
INJ2
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLU/RED.
INJ3
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRN/RED.
INJ4
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour PINK.
Not connected (N/C)
Cavity: Unused
Confirmed

Haltech E6H/M main harness drawing, rev A

Not connected (N/C)
Cavity: Unused
Confirmed

Haltech E6H/M main harness drawing, rev A

+13VDC ECU
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour RED/WHT.
GND
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLK.
AUXILIARY OUT
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRN/BLK.
AUXILIARY IN
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRN.
AIR TEMP
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour GRY.
COOLANT
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour VIO.
THROTTLE POS
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour WHT.
GND
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLK.
PUMP RELAY
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLK/YEL.
DIG OUT 2
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour BLU.
DIG OUT 1
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour WHT/BLK.
IGN OUT
Cavity: Populated
Confirmed

Haltech E6H/M main harness drawing, rev A

Harness wire colour L. GRN.