Adaptronic eSel020 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 240SX KA24DE and N14 Pulsar/Sunny GTi-R or SR20VE applications listed by Adaptronic. Adaptronic eSel020 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel020 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel020 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
A structured pin index with a redrawn connector face is in Adaptronic eSel020 connector pinout.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
From the Adaptronic eSel020 installation guide, pages 22–24. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 106 uses AUX 7 by default; the SR20VE installation changes jumpers J6 and J7 to select AUX 3.
| Factory pin | Factory function | Adaptronic function | Comments |
|---|---|---|---|
| 101 | Injector for cylinder 1 | Injector Output 3 | — |
| 102 | Purge valve | Aux Output 4 | GTiR no connection. SR20VE = VVL intake |
| 103 | Injector for cylinder 3 | Injector Output 4 | — |
| 104 | Fuel pump relay | Aux Output 5 | — |
| 105 | Fuel pump voltage control | +5V output | Connected straight to +5V inside ECU |
| 106 | Aircon relay | Aux Output 7 - can connect to Aux 3 with jumper change inside ECU | VVL exhaust on SR20VE |
| 107 | Ground | Power Ground | — |
| 108 | Ground | Power Ground | — |
| 109 | Constant Power | Const 12V | Straight from battery via fuse |
| 110 | Injector for cylinder 2 | Injector Output 2 | — |
| 111 | Boost control | Aux Output 3 | — |
| 112 | Injector for cylinder 4 | Injector Output 1 | — |
| 113 | Idle Control Valve | Aux Output 2 | — |
| 114 | NC | Aux Output 1 | Spare output |
| 115 | NC | — | — |
| 116 | Ground | Power Ground | — |
| 1 | To Igniter | Ignition output 1 | — |
| 2 | Tachometer | Ignition output 3 | — |
| 3 | Resistor / Condenser | — | Input from ignition coil - unused |
| 4 | ECCS relay | Pulled low by +12V ignition input | — |
| 5 | NC | Ignition output 2 (not used usually) | — |
| 6 | Ground | Power Ground | — |
| 7 | Data link connector | Ignition output 4 (not used usually) | — |
| 8 | Exhaust temperature | Aux Temperature signal input | — |
| 9 | Cooling fan relay | Aux Output 8 | — |
| 10 | Aircon relay | Aux Output 7 | — |
| 11 | NC | Aux Output 7 | A/C relay on GTiR |
| 12 | Auto Transmission | Digital Input 5 | Spare input |
| 13 | Ground | Power Ground | — |
| 14 | Clock | External 0-5V input | Spare input |
| 15 | Data link connector | Digital Input 4 | Spare input |
| 16 | AFM signal | MAP signal input | AFM signal pin can be used for MAP signal when fitting an external MAP sensor |
| 17 | AFM GND | Sensor Ground | — |
| 18 | Engine Coolant Temperature | ECT signal input | — |
| 19 | O2/EGO sensor signal | O2/EGO signal input | — |
| 20 | Throttle Position Sensor | TPS signal input | — |
| 21 | Sensor ground | Sensor Ground | — |
| 22 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Variable-width pulses each period, for cylinder and TDC identification |
| 23 | Data link connector | CAS 3 input | Available for flex fuel input |
| 24 | Malfunction indicator lamp | Aux Output 6 | — |
| 25 | Exhaust temperature warning light | — | — |
| 26 | NC | Digital Input 6 | Spare input |
| 27 | Knock sensor signal | Knock input | — |
| 28 | Auto Transmission | Digital Input 7 | Spare input |
| 29 | Sensor ground | Sensor Ground | — |
| 30 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Connected to pin 22 |
| 31 | 1 deg Cam Angle Sensor Signal | CAS 1 input | Connected to pin 40 |
| 32 | Speedometer | MVSS1 | — |
| 33 | NC | MVSS2 input | Additional input for traction control |
| 34 | Starter | Digital Input 8 | Spare input (ECU does not require starter input signal) |
| 35 | Neutral switch | Digital Input 1 | — |
| 36 | Ignition switch | +12V Ignition | Also triggers ECCS relay output |
| 37 | +5V out | +5V output | +5V power supply for sensors |
| 38 | From ECCS relay | — | Not used by our ECU |
| 39 | Ground | Power Ground | — |
| 40 | 1 deg Cam Angle Sensor Signal | CAS 1 input | 1 degree pulses for calculating ignition timing |
| 41 | Aircon request input | Digital Input 3 | — |
| 42 | Auto Transmission | SVSS1 input | Additional input for traction control |
| 43 | Power steering load input | Digital Input 2 | — |
| 44 | Auto Transmission | SVSS2 input | Additional input for traction control |
| 45 | Air Temperature | Air Temperature signal input | Not used on all models but the pin is available to add an air temperature sensor |
| 46 | Constant Power | — | — |
| 47 | From ECCS relay | — | — |
| 48 | Ground | Power Ground | — |
Manufacturer photograph
