by llandowtuninguk@gmail.com Link the new FT350/FT400 connector pinout article; add manufacturer-listed supported configurations and a Not established note on the processor.
Removed text is struck through; added text is highlighted.
FT400 product image from the FuelTech manufacturer manual, page 5; reproduced with permission.
FuelTech FT400 is a Earlier FT generation engine-management unit. Early colour-touchscreen ECU with two injection banks, seven auxiliary outputs and electronic-throttle support, according to the shared manual. FuelTech model documentation · FuelTech range comparison.
Identification and software
Record the exact model, serial, harness, firmware and configured outputs; similarly named FT models may use different connectors and functions. Tuning software: ECU Manager / Datalogger. FuelTech software and compatibility.
Wiring and pinout
Use the model-specific manual and the current FuelTech manuals index for connector view, cavity numbering, fuse values, sensor grounds and injector-driver limits. The manufacturer wiring archive contains installation-specific examples; match the exact ECU and harness before wiring. Pin functions depend on the model, hardware and configured output.
See FuelTech engine-management family for other models and company background. FuelTech is based in Brazil and has a US operation in Georgia. Sources reviewed 17 November 2026.
24-way main harness connector
Functions are from the FuelTech FT350 / FT400 manual, version 2.0, section 5.1. The source shows the rear of the harness connector. Inputs 2 and 4 have variant-specific recommended applications; check the model and configuration. Ground requirements in this manual differ from other FT generations.
PinFunction1Tachometer output (green)2Auxiliary output #3 (yellow 3)3Input 1 — intake air temperature (white/blue)4Auxiliary output #2 (yellow 2)5Input 2 — configurable sensor (white)6Auxiliary output #1 (yellow 1)7Input 3 — coolant temperature (pink)8Auxiliary output #4 (yellow 4)9Input 4 — configurable sensor (blue)10Ignition output E (gray E)11TPS signal / TPS 1 on electronic throttle (orange)12Ignition output D (gray D)13MAP signal output (yellow/red)14Ignition output C (gray C)15Camshaft position sensor input (green/yellow)16Ignition output B (gray B)17RPM signal input (shielded cable)18Ignition output A (gray A)19Battery negative / signal ground (black)205 V sensor supply (green/red)21Switched 12 V supply (red)22Power ground (black/white)23Fuel injector bank B negative (brown)24Fuel injector bank A negative (purple)
FT400 16-way auxiliary connector
Section 5.2 applies this connector to FT400 only. The manufacturer's table repeats “auxiliary #7” for pins 4, 6 and 8, although the harness diagram labels them #7, #6 and #5 respectively. Confirm these outputs and wiring with FuelTech; the table also disagrees with the diagram on the #1/#2 suffixes of the paired motor wire colours, while agreeing on their motor function.
PinFunction1O2 sensor input2Ignition output F3Electronic throttle TPS 24Auxiliary output #7 (yellow #7)5Two-step input6Yellow #6 auxiliary output — table calls it #7; see note7A/C button input8Yellow #5 auxiliary output — table calls it #7; see note9Power ground10Pedal signal #111Throttle or pedal sensor ground output12Pedal signal #213Electronic throttle motor #1 / step motor coil #114Electronic throttle motor #2 / step motor coil #215Electronic throttle motor #1 / step motor coil #116Electronic throttle motor #2 / step motor coil #2
Structured pinout
A structured pin index and redrawn connector diagrams are in FuelTech FT350 and FT400 connector pinout. It covers the shared 24-way main connector and the FT400's 16-way auxiliary connector.
Supported configurations
FuelTech's FT350 / FT400 manual (section 4, manufacturer specification) lists support for 1, 2, 3, 4, 5, 6, 8, 10 and 12-cylinder engines up to 16,000 rpm, with a built-in 7 bar (100 psi) MAP sensor and a 4.3-inch colour touch screen. Ignition is controlled from a crankshaft trigger wheel or a distributor. Fuel is delivered through two independent injector banks controlling up to twelve injectors, or more with a peak-and-hold module. The FT400 adds electronic pedal and throttle control, closed-loop lambda control, automatic fuel-map adjustment and seven auxiliary outputs. The FT350 has four auxiliary outputs and four configurable sensor inputs. The listed working temperature range is −10 °C to 60 °C. FuelTech FT350 / FT400 manual, accessed 19 November 2026.
Not established
The microcontroller used in the FT350 and FT400 is not named in FuelTech's published documentation.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: FuelTech FT400FT400 product image from the FuelTech manufacturer manual, page 5; reproduced with permission.
FuelTech FT400 is a Earlier FT generation engine-management unit. Early colour-touchscreen ECU with two injection banks, seven auxiliary outputs and electronic-throttle support, according to the shared manual. FuelTech model documentation · FuelTech range comparison.
Identification and software
Record the exact model, serial, harness, firmware and configured outputs; similarly named FT models may use different connectors and functions. Tuning software: ECU Manager / Datalogger. FuelTech software and compatibility.
Wiring and pinout
Use the model-specific manual and the current FuelTech manuals index for connector view, cavity numbering, fuse values, sensor grounds and injector-driver limits. The manufacturer wiring archive contains installation-specific examples; match the exact ECU and harness before wiring. Pin functions depend on the model, hardware and configured output.
See FuelTech engine-management family for other models and company background. FuelTech is based in Brazil and has a US operation in Georgia. Sources reviewed 17 November 2026.
24-way main harness connector
Functions are from the FuelTech FT350 / FT400 manual, version 2.0, section 5.1. The source shows the rear of the harness connector. Inputs 2 and 4 have variant-specific recommended applications; check the model and configuration. Ground requirements in this manual differ from other FT generations.
Pin
Function
1
Tachometer output (green)
2
Auxiliary output #3 (yellow 3)
3
Input 1 — intake air temperature (white/blue)
4
Auxiliary output #2 (yellow 2)
5
Input 2 — configurable sensor (white)
6
Auxiliary output #1 (yellow 1)
7
Input 3 — coolant temperature (pink)
8
Auxiliary output #4 (yellow 4)
9
Input 4 — configurable sensor (blue)
10
Ignition output E (gray E)
11
TPS signal / TPS 1 on electronic throttle (orange)
12
Ignition output D (gray D)
13
MAP signal output (yellow/red)
14
Ignition output C (gray C)
15
Camshaft position sensor input (green/yellow)
16
Ignition output B (gray B)
17
RPM signal input (shielded cable)
18
Ignition output A (gray A)
19
Battery negative / signal ground (black)
20
5 V sensor supply (green/red)
21
Switched 12 V supply (red)
22
Power ground (black/white)
23
Fuel injector bank B negative (brown)
24
Fuel injector bank A negative (purple)
FT400 16-way auxiliary connector
Section 5.2 applies this connector to FT400 only. The manufacturer's table repeats “auxiliary #7” for pins 4, 6 and 8, although the harness diagram labels them #7, #6 and #5 respectively. Confirm these outputs and wiring with FuelTech; the table also disagrees with the diagram on the #1/#2 suffixes of the paired motor wire colours, while agreeing on their motor function.
Pin
Function
1
O2 sensor input
2
Ignition output F
3
Electronic throttle TPS 2
4
Auxiliary output #7 (yellow #7)
5
Two-step input
6
Yellow #6 auxiliary output — table calls it #7; see note
7
A/C button input
8
Yellow #5 auxiliary output — table calls it #7; see note
9
Power ground
10
Pedal signal #1
11
Throttle or pedal sensor ground output
12
Pedal signal #2
13
Electronic throttle motor #1 / step motor coil #1
14
Electronic throttle motor #2 / step motor coil #2
15
Electronic throttle motor #1 / step motor coil #1
16
Electronic throttle motor #2 / step motor coil #2
Structured pinout
A structured pin index and redrawn connector diagrams are in FuelTech FT350 and FT400 connector pinout. It covers the shared 24-way main connector and the FT400's 16-way auxiliary connector.
Supported configurations
FuelTech's FT350 / FT400 manual (section 4, manufacturer specification) lists support for 1, 2, 3, 4, 5, 6, 8, 10 and 12-cylinder engines up to 16,000 rpm, with a built-in 7 bar (100 psi) MAP sensor and a 4.3-inch colour touch screen. Ignition is controlled from a crankshaft trigger wheel or a distributor. Fuel is delivered through two independent injector banks controlling up to twelve injectors, or more with a peak-and-hold module. The FT400 adds electronic pedal and throttle control, closed-loop lambda control, automatic fuel-map adjustment and seven auxiliary outputs. The FT350 has four auxiliary outputs and four configurable sensor inputs. The listed working temperature range is −10 °C to 60 °C. FuelTech FT350 / FT400 manual, accessed 19 November 2026.
Not established
The microcontroller used in the FT350 and FT400 is not named in FuelTech's published documentation.
Revision 4: FuelTech FT400FT400 product image from the FuelTech manufacturer manual, page 5; reproduced with permission.
FuelTech FT400 is a Earlier FT generation engine-management unit. Early colour-touchscreen ECU with two injection banks, seven auxiliary outputs and electronic-throttle support, according to the shared manual. FuelTech model documentation · FuelTech range comparison.
Identification and software
Record the exact model, serial, harness, firmware and configured outputs; similarly named FT models may use different connectors and functions. Tuning software: ECU Manager / Datalogger. FuelTech software and compatibility.
Wiring and pinout
Use the model-specific manual and the current FuelTech manuals index for connector view, cavity numbering, fuse values, sensor grounds and injector-driver limits. The manufacturer wiring archive contains installation-specific examples; match the exact ECU and harness before wiring. Pin functions depend on the model, hardware and configured output.
See FuelTech engine-management family for other models and company background. FuelTech is based in Brazil and has a US operation in Georgia. Sources reviewed 17 November 2026.
24-way main harness connector
Functions are from the FuelTech FT350 / FT400 manual, version 2.0, section 5.1. The source shows the rear of the harness connector. Inputs 2 and 4 have variant-specific recommended applications; check the model and configuration. Ground requirements in this manual differ from other FT generations.
Pin
Function
1
Tachometer output (green)
2
Auxiliary output #3 (yellow 3)
3
Input 1 — intake air temperature (white/blue)
4
Auxiliary output #2 (yellow 2)
5
Input 2 — configurable sensor (white)
6
Auxiliary output #1 (yellow 1)
7
Input 3 — coolant temperature (pink)
8
Auxiliary output #4 (yellow 4)
9
Input 4 — configurable sensor (blue)
10
Ignition output E (gray E)
11
TPS signal / TPS 1 on electronic throttle (orange)
12
Ignition output D (gray D)
13
MAP signal output (yellow/red)
14
Ignition output C (gray C)
15
Camshaft position sensor input (green/yellow)
16
Ignition output B (gray B)
17
RPM signal input (shielded cable)
18
Ignition output A (gray A)
19
Battery negative / signal ground (black)
20
5 V sensor supply (green/red)
21
Switched 12 V supply (red)
22
Power ground (black/white)
23
Fuel injector bank B negative (brown)
24
Fuel injector bank A negative (purple)
FT400 16-way auxiliary connector
Section 5.2 applies this connector to FT400 only. The manufacturer's table repeats “auxiliary #7” for pins 4, 6 and 8, although the harness diagram labels them #7, #6 and #5 respectively. Confirm these outputs and wiring with FuelTech; the table also disagrees with the diagram on the #1/#2 suffixes of the paired motor wire colours, while agreeing on their motor function.
Pin
Function
1
O2 sensor input
2
Ignition output F
3
Electronic throttle TPS 2
4
Auxiliary output #7 (yellow #7)
5
Two-step input
6
Yellow #6 auxiliary output — table calls it #7; see note
7
A/C button input
8
Yellow #5 auxiliary output — table calls it #7; see note
9
Power ground
10
Pedal signal #1
11
Throttle or pedal sensor ground output
12
Pedal signal #2
13
Electronic throttle motor #1 / step motor coil #1
14
Electronic throttle motor #2 / step motor coil #2
15
Electronic throttle motor #1 / step motor coil #1
16
Electronic throttle motor #2 / step motor coil #2
Structured pinout
A structured pin index and redrawn connector diagrams are in FuelTech FT350 and FT400 connector pinout. It covers the shared 24-way main connector and the FT400's 16-way auxiliary connector.
Supported configurations
FuelTech's FT350 / FT400 manual (section 4, manufacturer specification) lists support for 1, 2, 3, 4, 5, 6, 8, 10 and 12-cylinder engines up to 16,000 rpm, with a built-in 7 bar (100 psi) MAP sensor and a 4.3-inch colour touch screen. Ignition is controlled from a crankshaft trigger wheel or a distributor. Fuel is delivered through two independent injector banks controlling up to twelve injectors, or more with a peak-and-hold module. The FT400 adds electronic pedal and throttle control, closed-loop lambda control, automatic fuel-map adjustment and seven auxiliary outputs. The FT350 has four auxiliary outputs and four configurable sensor inputs. The listed working temperature range is −10 °C to 60 °C. FuelTech FT350 / FT400 manual, accessed 19 November 2026.
Not established
The microcontroller used in the FT350 and FT400 is not named in FuelTech's published documentation.