Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Motorsport Electronics ME221
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 4

Removed text is struck through; added text is highlighted.

ME221 Toyota Glanza EP91 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.

ME221 plug-in ECU for Toyota Glanza EP91. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.

Identification and application

ME supplies an EP91 plug-in alongside the EP82 variant. The GEN2 guide covers both; identify the actual original ECU and loom before transferring assignments. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.

Connector and pinout

Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.

Auxiliary connector assignments

The ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.

PinFunction in manufacturer guide1Injector 5 — 3.5 A FB protected2Injector 6 — 3.5 A FB protected3Injector 7 — 3.5 A FB protected4Injector 8 — 3.5 A FB protected5NC6NC7LS1 — 2 A PWM-capable8LS2 — 2 A PWM-capable9LS3 — 2 A PWM-capable10K-type EGT signal — ME442 only11DI 1 — 1 kΩ 5 V pull-up12DI 2 — 1 kΩ 5 V pull-up13DI 3 not available — boost button14Analogue volt 5 — 0–5 V15Analogue volt 6 — 0–5 V16Analogue volt 7 — 0–5 V17CAN 1 low — unterminated18CAN 1 high — unterminated195 V reference — 100 mA max20EGT and sensor ground

The guide states that the connector orientation differs between EP82 and EP91; follow the appropriate original diagram. EGT is marked for ME442 versions.

Processor

Motorsport Electronics does not publish the microcontroller part number. A distributor specification sheet for the ME221 lists a 120 MHz 32-bit RISC processor; this is a vendor specification rather than a component identification. ATP Turbo ME221 specification sheet (May 2023), accessed 19 November 2026.

Structured connector pinout

Every cavity of the EP82 and EP91 factory headers and the 20-way auxiliary connector, with the manufacturer's assignments, is drawn in Motorsport Electronics ME221 and ME442 EP82/EP91 plug-in connector pinout.

Software and installation

Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.

Sources reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Motorsport Electronics ME221 Toyota Glanza EP91 plug-in
ME221 Toyota Glanza EP91 plug-in ECU
ME221 Toyota Glanza EP91 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.

ME221 plug-in ECU for Toyota Glanza EP91. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.

Identification and application

ME supplies an EP91 plug-in alongside the EP82 variant. The GEN2 guide covers both; identify the actual original ECU and loom before transferring assignments. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.

Connector and pinout

Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.

Auxiliary connector assignments

The ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.

PinFunction in manufacturer guide
1Injector 5 — 3.5 A FB protected
2Injector 6 — 3.5 A FB protected
3Injector 7 — 3.5 A FB protected
4Injector 8 — 3.5 A FB protected
5NC
6NC
7LS1 — 2 A PWM-capable
8LS2 — 2 A PWM-capable
9LS3 — 2 A PWM-capable
10K-type EGT signal — ME442 only
11DI 1 — 1 kΩ 5 V pull-up
12DI 2 — 1 kΩ 5 V pull-up
13DI 3 not available — boost button
14Analogue volt 5 — 0–5 V
15Analogue volt 6 — 0–5 V
16Analogue volt 7 — 0–5 V
17CAN 1 low — unterminated
18CAN 1 high — unterminated
195 V reference — 100 mA max
20EGT and sensor ground

The guide states that the connector orientation differs between EP82 and EP91; follow the appropriate original diagram. EGT is marked for ME442 versions.

Processor

Motorsport Electronics does not publish the microcontroller part number. A distributor specification sheet for the ME221 lists a 120 MHz 32-bit RISC processor; this is a vendor specification rather than a component identification. ATP Turbo ME221 specification sheet (May 2023), accessed 19 November 2026.

Structured connector pinout

Every cavity of the EP82 and EP91 factory headers and the 20-way auxiliary connector, with the manufacturer's assignments, is drawn in Motorsport Electronics ME221 and ME442 EP82/EP91 plug-in connector pinout.

Software and installation

Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.

Sources reviewed 17 November 2026.

Revision 4: Motorsport Electronics ME221 Toyota Glanza EP91 plug-in
ME221 Toyota Glanza EP91 plug-in ECU
ME221 Toyota Glanza EP91 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.

ME221 plug-in ECU for Toyota Glanza EP91. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.

Identification and application

ME supplies an EP91 plug-in alongside the EP82 variant. The GEN2 guide covers both; identify the actual original ECU and loom before transferring assignments. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.

Connector and pinout

Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.

Auxiliary connector assignments

The ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.

PinFunction in manufacturer guide
1Injector 5 — 3.5 A FB protected
2Injector 6 — 3.5 A FB protected
3Injector 7 — 3.5 A FB protected
4Injector 8 — 3.5 A FB protected
5NC
6NC
7LS1 — 2 A PWM-capable
8LS2 — 2 A PWM-capable
9LS3 — 2 A PWM-capable
10K-type EGT signal — ME442 only
11DI 1 — 1 kΩ 5 V pull-up
12DI 2 — 1 kΩ 5 V pull-up
13DI 3 not available — boost button
14Analogue volt 5 — 0–5 V
15Analogue volt 6 — 0–5 V
16Analogue volt 7 — 0–5 V
17CAN 1 low — unterminated
18CAN 1 high — unterminated
195 V reference — 100 mA max
20EGT and sensor ground

The guide states that the connector orientation differs between EP82 and EP91; follow the appropriate original diagram. EGT is marked for ME442 versions.

Processor

Motorsport Electronics does not publish the microcontroller part number. A distributor specification sheet for the ME221 lists a 120 MHz 32-bit RISC processor; this is a vendor specification rather than a component identification. ATP Turbo ME221 specification sheet (May 2023), accessed 19 November 2026.

Structured connector pinout

Every cavity of the EP82 and EP91 factory headers and the 20-way auxiliary connector, with the manufacturer's assignments, is drawn in Motorsport Electronics ME221 and ME442 EP82/EP91 plug-in connector pinout.

Software and installation

Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.

Sources reviewed 17 November 2026.