Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Link standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 4 to revision 4
Removed text is struck through; added text is highlighted.
Link G4 Atom original is a documented G4 Link engine-management designation. The original G4 Atom is documented as a distinct pre-G4+ designation in period listings. Verify the actual generation rather than assuming an Atom, Atom II or AtomX harness is interchangeable. Identification source.
Identification and software
Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.
Model-specific wiring
The identified manufacturer documentation or legacy manual archive is the starting point for this model. An individual pin-by-pin allocation was not verified in this reference; obtain the exact matching manual and connector orientation before wiring.
See Link standalone ECUs for related models and generation distinctions.
Link's 2010 G4 wiring and installation manual names this generation and covers G4 Lightning, Atom, RX, Storm and Xtreme. Consult the model-specific connector layout.
Original G4 Atom header
From page 16 of Link's 2010 G4 wiring and installation manual; the drawing is viewed into the ECU header or the wire side of the loom connector. The manufacturer’s 26-position drawing gives connector functions by physical location but does not number its cavities. The row positions below are counted from the left in that drawing and are not manufacturer cavity numbers. This is the original G4 model; later G4+ or G4X connectors must be checked separately.
PositionFunctionLoom colourTop row, 1 from leftInj 4Brown/orangeTop row, 2 from leftIgnition 1BlueTop row, 3 from leftIgnition 2Blue/brownTop row, 4 from leftIgnition 3Blue/redTop row, 5 from leftIgnition 4Blue/orangeTop row, 6 from leftTrigger 1BlackTop row, 7 from leftTrigger 2RedSecond row, 1 from leftInj 3Brown/redSecond row, 2 from leftAux 1Orange/blackSecond row, 3 from leftAux 2Orange/brownSecond row, 4 from leftAux 3Orange/redSecond row, 5 from leftAux 4OrangeSecond row, 6 from left+14 VRedThird row, 1 from leftInj 2BrownThird row, 2 from leftDigital input 1Grey/blackThird row, 3 from leftTemperature 1YellowThird row, 4 from leftTemperature 2Yellow/brownThird row, 5 from leftGround outGreenThird row, 6 from leftShieldGreenBottom row, 1 from leftInj 1Brown/blackBottom row, 2 from leftDigital input 2Grey/brownBottom row, 3 from leftAnalogue volt 1Yellow/blueBottom row, 4 from leftAnalogue volt 2White/brownBottom row, 5 from left+5 VRed/blueBottom row, 6 from leftGroundBlackBottom row, 7 from leftGroundBlack
The structured pin index and redrawn header are in Link G4 Atom original connector pinout.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: Link G4 Atom original
Link G4 Atom original is a documented G4 Link engine-management designation. The original G4 Atom is documented as a distinct pre-G4+ designation in period listings. Verify the actual generation rather than assuming an Atom, Atom II or AtomX harness is interchangeable. Identification source.
Identification and software
Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.
Model-specific wiring
The identified manufacturer documentation or legacy manual archive is the starting point for this model. An individual pin-by-pin allocation was not verified in this reference; obtain the exact matching manual and connector orientation before wiring.
See Link standalone ECUs for related models and generation distinctions.
Link's 2010 G4 wiring and installation manual names this generation and covers G4 Lightning, Atom, RX, Storm and Xtreme. Consult the model-specific connector layout.
Original G4 Atom header
From page 16 of Link's 2010 G4 wiring and installation manual; the drawing is viewed into the ECU header or the wire side of the loom connector. The manufacturer’s 26-position drawing gives connector functions by physical location but does not number its cavities. The row positions below are counted from the left in that drawing and are not manufacturer cavity numbers. This is the original G4 model; later G4+ or G4X connectors must be checked separately.
| Position | Function | Loom colour |
|---|
| Top row, 1 from left | Inj 4 | Brown/orange |
| Top row, 2 from left | Ignition 1 | Blue |
| Top row, 3 from left | Ignition 2 | Blue/brown |
| Top row, 4 from left | Ignition 3 | Blue/red |
| Top row, 5 from left | Ignition 4 | Blue/orange |
| Top row, 6 from left | Trigger 1 | Black |
| Top row, 7 from left | Trigger 2 | Red |
| Second row, 1 from left | Inj 3 | Brown/red |
| Second row, 2 from left | Aux 1 | Orange/black |
| Second row, 3 from left | Aux 2 | Orange/brown |
| Second row, 4 from left | Aux 3 | Orange/red |
| Second row, 5 from left | Aux 4 | Orange |
| Second row, 6 from left | +14 V | Red |
| Third row, 1 from left | Inj 2 | Brown |
| Third row, 2 from left | Digital input 1 | Grey/black |
| Third row, 3 from left | Temperature 1 | Yellow |
| Third row, 4 from left | Temperature 2 | Yellow/brown |
| Third row, 5 from left | Ground out | Green |
| Third row, 6 from left | Shield | Green |
| Bottom row, 1 from left | Inj 1 | Brown/black |
| Bottom row, 2 from left | Digital input 2 | Grey/brown |
| Bottom row, 3 from left | Analogue volt 1 | Yellow/blue |
| Bottom row, 4 from left | Analogue volt 2 | White/brown |
| Bottom row, 5 from left | +5 V | Red/blue |
| Bottom row, 6 from left | Ground | Black |
| Bottom row, 7 from left | Ground | Black |
The structured pin index and redrawn header are in Link G4 Atom original connector pinout.
Revision 4: Link G4 Atom original
Link G4 Atom original is a documented G4 Link engine-management designation. The original G4 Atom is documented as a distinct pre-G4+ designation in period listings. Verify the actual generation rather than assuming an Atom, Atom II or AtomX harness is interchangeable. Identification source.
Identification and software
Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.
Model-specific wiring
The identified manufacturer documentation or legacy manual archive is the starting point for this model. An individual pin-by-pin allocation was not verified in this reference; obtain the exact matching manual and connector orientation before wiring.
See Link standalone ECUs for related models and generation distinctions.
Link's 2010 G4 wiring and installation manual names this generation and covers G4 Lightning, Atom, RX, Storm and Xtreme. Consult the model-specific connector layout.
Original G4 Atom header
From page 16 of Link's 2010 G4 wiring and installation manual; the drawing is viewed into the ECU header or the wire side of the loom connector. The manufacturer’s 26-position drawing gives connector functions by physical location but does not number its cavities. The row positions below are counted from the left in that drawing and are not manufacturer cavity numbers. This is the original G4 model; later G4+ or G4X connectors must be checked separately.
| Position | Function | Loom colour |
|---|
| Top row, 1 from left | Inj 4 | Brown/orange |
| Top row, 2 from left | Ignition 1 | Blue |
| Top row, 3 from left | Ignition 2 | Blue/brown |
| Top row, 4 from left | Ignition 3 | Blue/red |
| Top row, 5 from left | Ignition 4 | Blue/orange |
| Top row, 6 from left | Trigger 1 | Black |
| Top row, 7 from left | Trigger 2 | Red |
| Second row, 1 from left | Inj 3 | Brown/red |
| Second row, 2 from left | Aux 1 | Orange/black |
| Second row, 3 from left | Aux 2 | Orange/brown |
| Second row, 4 from left | Aux 3 | Orange/red |
| Second row, 5 from left | Aux 4 | Orange |
| Second row, 6 from left | +14 V | Red |
| Third row, 1 from left | Inj 2 | Brown |
| Third row, 2 from left | Digital input 1 | Grey/black |
| Third row, 3 from left | Temperature 1 | Yellow |
| Third row, 4 from left | Temperature 2 | Yellow/brown |
| Third row, 5 from left | Ground out | Green |
| Third row, 6 from left | Shield | Green |
| Bottom row, 1 from left | Inj 1 | Brown/black |
| Bottom row, 2 from left | Digital input 2 | Grey/brown |
| Bottom row, 3 from left | Analogue volt 1 | Yellow/blue |
| Bottom row, 4 from left | Analogue volt 2 | White/brown |
| Bottom row, 5 from left | +5 V | Red/blue |
| Bottom row, 6 from left | Ground | Black |
| Bottom row, 7 from left | Ground | Black |
The structured pin index and redrawn header are in Link G4 Atom original connector pinout.