
MoTeC M170 is an M1-family programmable ECU, part 13170. The manufacturer identifies it for up to 8 cylinders and port injection. M1 hardware is paired with a software package; features, channels and licences depend on the loaded package and hardware revision. MoTeC M170 product information and product image.
Identification and inputs/outputs
| Field | Manufacturer comparison |
|---|---|
| Injection hardware | 8 port injector outputs; 2 low-side injector outputs |
| Ignition | 8 low-side ignition outputs |
| Half-bridge outputs | 6 |
| Universal digital inputs | 8 |
| Analogue voltage / temperature inputs | 8 / 4 |
| CAN buses | 1 |
| Connector configuration | one Autosport, 66 positions |
Numbers describe hardware capacity; they do not establish simultaneous availability for a specific application. MoTeC’s M1 comparison distinguishes port, inductive direct and piezo direct drivers. Check the exact injector and package; an external driver is not interchangeable with an internal driver.
Wiring and pinout
Use the M170 connector pinout and datasheet on the manufacturer product page. Connector type, keying and positions vary across M1 models; do not copy pin functions from another ECU. Verify the hardware revision, package, output allocations, wiring orientation, electrical limits and power and earth provisions against the exact unit.
A structured, redrawn version of the manufacturer pin table is in MoTeC M170 connector pinout.
Manufacturer connector tables
These tables reproduce the complete connector position and designation lists from the MoTeC M170 datasheet. Pin identifiers are kept as printed, including letter case. Check the original connector views, mating key, wire size, electrical ratings and hardware revision before connecting. Output functions depend on the ECU package and configuration; direct-injection models require their specified drivers and precautions.
Connector A — 66 positions
| Pin | Designation | Function |
|---|---|---|
| A01 | IGN_LS1 | Low Side Ignition 1 |
| A02 | IGN_LS8 | Low Side Ignition 8 |
| A03 | IGN_LS7 | Low Side Ignition 7 |
| A04 | IGN_LS3 | Low Side Ignition 3 |
| A05 | IGN_LS2 | Low Side Ignition 2 |
| A06 | AV3 | Analogue Voltage Input 3 |
| A07 | AV4 | Analogue Voltage Input 4 |
| A08 | OUT_HB2 | Half Bridge Output 2 |
| A09 | OUT_HB1 | Half Bridge Output 1 |
| A10 | IGN_LS4 | Low Side Ignition 4 |
| A11 | SEN_0V_A | Sensor 0V A |
| A12 | AV5 | Analogue Voltage Input 5 |
| A13 | UDIG7 | Universal Digital Input 7 |
| A14 | BAT_NEG1 | Battery Negative |
| A15 | BAT_NEG2 | Battery Negative |
| A16 | SEN_5V0_A | Sensor 5.0V A |
| A17 | IGN_LS5 | Low Side Ignition 5 |
| A18 | AV2 | Analogue Voltage Input 2 |
| A19 | BAT_NEG3 | Battery Negative |
| A20 | BAT_NEG4 | Battery Negative |
| A21 | BAT_NEG5 | Battery Negative |
| A22 | UDIG8 | Universal Digital Input 8 |
| A23 | BAT_POS | Battery Positive |
| A24 | INJ_PH5 | Peak Hold Injector 5 |
| A25 | IGN_LS6 | Low Side Ignition 6 |
| A26 | AV1 | Analogue Voltage Input 1 |
| A27 | SEN_0V_B | Sensor 0V B |
| A28 | AT1 | Analogue Temperature Input 1 |
| A29 | KNOCK1 | Knock Input 1 |
| A30 | AT3 | Analogue Temperature Input 3 |
| A31 | CAN_LO | CAN Bus 1 Low |
| A32 | BAT_POS | Battery Positive |
| A33 | INJ_PH1 | Peak Hold Injector 1 |
| A34 | SEN_5V0_B | Sensor 5.0V B |
| A35 | AV7 | Analogue Voltage Input 7 |
| A36 | AV6 | Analogue Voltage Input 6 |
| A37 | SEN_6V3 | Sensor 6.3V |
| A38 | AT2 | Analogue Temperature Input 2 |
| A39 | AT4 | Analogue Temperature Input 4 |
| A40 | CAN_HI | CAN Bus 1 High |
| A41 | BAT_POS | Battery Positive |
| A42 | INJ_PH6 | Peak Hold Injector 6 |
| A43 | INJ_LS1 | Low Side Injector 1 |
| A44 | AV8 | Analogue Voltage Input 8 |
| A45 | UDIG4 | Universal Digital Input 4 |
| A46 | UDIG3 | Universal Digital Input 3 |
| A47 | ETH_TX- | Ethernet Transmit- |
| A48 | ETH_TX+ | Ethernet Transmit+ |
| A49 | UDIG1 | Universal Digital Input 1 |
| A50 | INJ_PH2 | Peak Hold Injector 2 |
| A51 | INJ_LS2 | Low Side Injector 2 |
| A52 | UDIG5 | Universal Digital Input 5 |
| A53 | UDIG6 | Universal Digital Input 6 |
| A54 | BAT_BAK | Battery Backup |
| A55 | ETH_RX+ | Ethernet Receive+ |
| A56 | UDIG2 | Universal Digital Input 2 |
| A57 | INJ_PH7 | Peak Hold Injector 7 |
| A58 | OUT_HB5 | Half Bridge Output 5 |
| A59 | OUT_HB3 | Half Bridge Output 3 |
| A60 | KNOCK2 | Knock Input 2 |
| A61 | ETH_RX- | Ethernet Receive- |
| A62 | INJ_PH8 | Peak Hold Injector 8 |
| A63 | INJ_PH3 | Peak Hold Injector 3 |
| A64 | OUT_HB6 | Half Bridge Output 6 |
| A65 | OUT_HB4 | Half Bridge Output 4 |
| A66 | INJ_PH4 | Peak Hold Injector 4 |
Software and context
M1 Tune configures supported packages, while M1 Build is used to develop packages. ECU and logging features depend on installed licences. MoTeC downloads; MoTeC model index.