Link G3 LinkPlus is a documented G3 Link engine-management designation. Link's support forum lists a LinkPlus G3 wiring and installation manual. The manufacturer connector kit for G3 LinkPlus uses four housings, distinguishing it from the single 26-way G3 LEM connector. Identification source.
Processor and inputs and outputs
The G3 generation was released in 2007 in a silver and black case and, according to Link's company history, was designed to make fuller use of the ST10 16-bit microcontroller family first used in the G2; the history does not give the exact ST10 part (manufacturer history, single source). The same history lists the LinkPlus G3 with 8 injection drives, 8 ignition drives, 4 temperature inputs, 9 analogue inputs, 12 digital inputs and 11 auxiliary outputs, against 4 injection and 2 ignition drives on the smaller LEM G3.
Identification and software
Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.
Model-specific wiring
The identified manufacturer documentation or legacy manual archive is the starting point for this model. An individual pin-by-pin allocation was not verified in this reference; obtain the exact matching manual and connector orientation before wiring.
See Link standalone ECUs for related models and generation distinctions.
LinkPlus G3 breakout loom colour reference
The following signal and loom-colour list comes from Link Electrosystems drawing G06, LinkPlus G3 ECU Pinout, version 1.0, as reproduced in an archival copy. This is a wire-colour reference, not a numbered connector-cavity map. The diagram says to view the ECU header from the connector wire side. Confirm connector positions against the original drawing and the exact ECU, loom and internal build. The manufacturer's G2/G3 manual index lists the LinkPlus G3 wiring manual. Do not transfer these colours to LEM G3, G1 or G2 models.
| Signal | Link G06 loom colour |
|---|---|
| Injector 1 | Brown/Black |
| Injector 2 | Brown |
| Injector 3 | Brown/Red |
| Injector 4 | Brown/Orange |
| Injector 5 | Brown/Yellow |
| Injector 6 | Brown/Green |
| Injector 7 | Brown/Blue |
| Injector 8 | Brown/Purple |
| Ignition 1 | Blue/Black |
| Ignition 2 | Blue/Brown |
| Ignition 3 | Blue/Red |
| Ignition 4 | Blue/Orange |
| Ignition 5 | Blue/Yellow |
| Ignition 6 | Blue/Green |
| Ignition 7 | Blue |
| Ignition 8 | Blue/Purple |
| Auxiliary output 1 | Orange/Black |
| Auxiliary output 2 | Orange/Brown |
| Auxiliary output 3 | Orange/Red |
| Auxiliary output 4 | Orange |
| Auxiliary output 5 | Orange/Yellow |
| Auxiliary output 6 | Orange/Green |
| Auxiliary output 7 | Orange/Blue |
| Auxiliary output 8 | Orange/Purple |
| Digital input 1 | Grey/Black |
| Digital input 2 | Grey/Brown |
| Digital input 3 | Grey/Red |
| Digital input 4 | Grey/Orange |
| Digital input 5 | Grey/Yellow |
| Digital input 6 | Grey/Green |
| Digital input 7 | Grey/Blue |
| Digital input 8 | Grey |
| Analogue voltage input 1 | White/Black |
| Analogue voltage input 2 | White/Brown |
| Analogue voltage input 3 | White/Red |
| Analogue voltage input 4 | White/Orange |
| Analogue voltage input 5 | White/Yellow |
| Analogue voltage input 6 | White/Green |
| Analogue temperature 1 | Yellow (ECT) |
| Analogue temperature 2 | Yellow/Brown (IAT) |
| Analogue temperature 3 | Yellow/Red |
| Analogue temperature 4 | Yellow/Orange |
| Load 1 (MAP) | White/Blue |
| Load 3 (TPS) | White |
| Trigger 1 | Yellow, screened cable |
| Trigger 2 | Blue, screened cable |
| Knock 1 | Blue, screened cable |
| Knock 2 | Blue, screened cable |
| Power +12V | Red |
| Power ground | Black |
| Sensor ground | Green |
| +5V output | Red/Blue |
| +8V output | Red/White |
Colours and labels refer to Link's G3 loom, and are not a substitute for identifying cavity orientation, ECU configuration and actual wiring. A different or repaired loom can use different colours.
Sources
- Link ECU company history (G2 and G3 generations). Link Engine Management, manufacturer web page; the address now serves the store front page and the G2 and G3 text was seen in search summary. Accessed 19 November 2026.