Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Sagem
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Where this computer is specified

Renault fault finding MR-366, section 17B, covers the Sagem S3000, program AD, diagnostic number Vdiag 4C or 54. The vehicles in that document are Mégane II phase 2 and Scénic II phase 2. The engines are K4J 740, K4M 766, 812 and 813, K4M 788 on LPG, F4R 770 and 771, F4R-T 776, and F4R-T 774 on the Mégane II phase 2 Renault Sport. Vdiag 54 adds one fault and one command that 4C does not have: DF363 for the camshaft dephaser, and TEST3 for its solenoid. A file catalogue that puts the same name on another Renault is not this specification. The family index is Sagem. The preceding 112-track controller is S2000.

Processor

The AutoTuner ECU compatibility list (tool compatibility listing, export date 28 October 2026) gives the S3000 microcontroller as "SH705x", without a more specific device. This is a tool-vendor listing, not manufacturer documentation, and the exact part and flash device are not given.

The computer

The computer is a 128-track Sagem S3000 with flash EEPROM. It controls injection and ignition. Injection is multipoint and sequential. There are four injectors and four pencil coils. The throttle is motorised, with its own motor and two position potentiometers, and it sets both the idle speed and the intake air. The Mégane particulars add that the fuel system has no return to the tank, and that the pressure regulator is on the pump and gauge assembly.

The composition list in the fault-finding text is: accelerator potentiometer, clutch switch, top-dead-centre sensor, atmospheric-pressure sensor, air-temperature sensor, coolant-temperature sensor, upstream and downstream oxygen sensors, cruise-control switches, the canister, the computer, the motorised throttle, the four injectors, the four pencil coils, and a knock sensor. A camshaft-dephaser solenoid and a camshaft-position sensor are listed for the non-LPG K4M only. A turbo-pressure sensor, an electric coolant pump, a wastegate solenoid and a turbocharging solenoid are listed for the F4R turbo only.

The computer talks to the air conditioning, the UCH, the protection and switching unit, the automatic-gearbox computer, the airbag, ABS and ESP, and the instrument panel. The Mégane particulars say the protection and switching unit supplies the coils, the fuel pump, the air-conditioning compressor, the cooling fan, and injection actuators such as the injectors and the canister-purge valve. Those relays are not serviceable parts. The computer also receives the alternator's available electrical power on the multiplex network, so the vehicle's electrical load is kept inside what the alternator can supply.

Torque, idle and fuel

The torque structure exists because ESP and the automatic gearbox can ask for a torque. Each of those systems sends a request on the multiplex network. The computer arbitrates between those requests and the driver's request, from the pedal or from cruise control and the speed limiter. The result is a torque setpoint. From that setpoint the computer calculates the throttle position, the ignition advance, and, on a turbo engine, the wastegate setpoint.

The fuel pump is run for one second at ignition on, to build pressure for a start after the car has stood. While the engine is running, the pump relay stays commanded. That command is status ET047. The canister is purged by a duty cycle at one of two frequencies, 8 Hz or 20 Hz, chosen from engine speed.

Idle is the motorised throttle. The setpoint, parameter PR010, depends on coolant temperature, emissions programming, air conditioning, the gearbox selector, power-steering load, the cabin heater resistors, oil temperature, and the electrical balance. If battery voltage stays below 12.7 V the idle is raised by up to 160 rpm. The adaptive part of the idle opening, PR090, is learned only at warm idle with no air conditioning, fan or power steering, and only once the coolant is above 75 °C and the engine has been running for a minute. The integral correction, PR444, accounts for the consumers. The Mégane particulars also correct hot idle for coolant temperature, battery voltage and air conditioning, and add oil pressure on the K4M and the automatic selector on the F4R. If a manifold-pressure sensor fault is present and stored, that text sets the idle setpoint to 896 rpm on the K4J and K4M, and 1024 rpm on the F4R.

The accelerator pedal is a double potentiometer. In the Mégane particulars the first track is 0 to 5 V and the second is 0 to 2.5 V, half of the first, and the computer compares them. After a pedal is replaced, the reading at ignition on is taken as the released-pedal reference.

Phasing and the dephaser

Starting injection is semi-sequential: injectors 1 and 4 together, then 2 and 3. The system then goes sequential, so a start is still possible if the engine is not yet phased. The intended sequential order is 1-3-4-2. If the memorised phasing from the last stall was wrong, the injections can be shifted by two cylinders, so the order becomes 4-2-1-3. The first phasing strategy, called memo phasing, uses the data stored when the engine last stalled. Wait until the power latch has finished, and that data has been saved, before disconnecting the computer. A second strategy then checks the decision by looking at engine torque.

The camshaft sensor, fitted on the non-LPG K4M, identifies the cylinders for sequential injection and reads the inlet-camshaft position. The Mégane particulars say the F4R and the K4J have no cylinder-1 sensor on the camshaft, so those engines phase in software from the top-dead-centre sensor, still starting semi-sequential and then going sequential. The K4M uses the camshaft sensor for the same start sequence. The fault-finding text agrees that phasing is done in software where there is no camshaft sensor. It then says that this is the case on engines which do not have a camshaft dephaser, and that configuration LC008 shows the dephaser. That sentence does not match the F4R. Both documents give the F4R an inlet dephaser, and the Mégane particulars still phase the F4R from the top-dead-centre sensor because it has no camshaft sensor. Use the engine code and LC008, not the one sentence.

The dephaser itself is not one component. On the K4M it is continuously variable from 0 to 43 degrees of crankshaft angle, driven by a solenoid on a duty cycle. On the F4R and F4R-T it is an on-or-off solenoid. The Mégane dephaser section describes the K4M and the F4R and does not describe a K4J dephaser.

The F4R turbo

Boost is set by the wastegate. A normally open solenoid sits on the inlet pipe between the air filter and the turbocharger inlet. At rest, that solenoid connects turbocharger outlet pressure to the wastegate diaphragm, the wastegate opens, and the pressure stays at the minimum for the engine, about 1350 to 1400 mbar, regardless of engine speed. When the solenoid is driven, the pressure signal is diverted to the compressor inlet, the diaphragm is no longer fed with boost, and the wastegate closes to the position the regulation asks for.

The same section says the computer holds full-load torque constant despite air temperature and atmospheric pressure, and it states that maximum as 275 Nm and 125 kW, with turbocharging pressure never above 1800 mbar. At 20 °C air temperature the full-load boost is lower than at 50 °C. The document lists both the F4R-T 776 and the Renault Sport F4R-T 774, and this sentence does not say which of those engines the 275 Nm and 125 kW belong to. Do not read it as the Sport output.

Ignition, mixture and the rev limit

Advance is calculated per cylinder. It can be negative, and the stated range is −23.625 degrees to +72 degrees, including the knock correction. The slow knock correction is the largest advance taken off any one cylinder. If no cylinder is knocking, that correction is zero. Injection time is calculated continuously and can be zero, on overrun or at the rev limit.

Mixture is held near a richness of 1 for the catalyst. The upstream oxygen sensor provides the rich or lean signal, and the correction, PR138, is centred near 50 percent, between 0 and 100. The adaptive gain and offset, PR143 and PR144, move the map so that regulation sits on 50 percent. After programming is cleared they start at 50 percent. Upstream-sensor heating is active only with the engine running, and it is switched off above 140 km/h or when the engine is under load. The downstream sensor is the second loop. It judges the upstream sensor and compensates for its drift. Whether each sensor is fitted is configuration LC003 and LC004.

The Mégane particulars give a cold cut and a hot cut, and they do not separate a turbo F4R from the others. Below 60 °C, or for 10 seconds after start, the K4J cuts at 5800 rpm. Below 75 °C, or for 10 seconds after start, the K4M cuts at 5800 rpm. Below 75 °C, or for up to 17 minutes after start, the F4R cuts at 5900 rpm. Once hot, the K4J and K4M cut at 6500 rpm in any gear, manual or automatic. The hot F4R cuts at 6000 rpm with a manual gearbox and 6300 rpm with an automatic. Those are that text's figures. They are not the Laguna S2000 limits.

Diagnostics and the immobiliser

The diagnostic tool in the fault-finding document is Renault CLIP with a multiplex-line sensor. Fault-finding mode is ignition on without the engine starting: the card is in the reader and the start button is held for more than five seconds while the start conditions are not met. To drop the ignition feed, disconnect the tool and press the start button twice for less than three seconds. A stored impact is cleared by switching the ignition off for 10 seconds, switching it back on, and then clearing the faults. Disconnect the injection computer before any welding.

On-board diagnostics in the same document cover the catalyst, the upstream oxygen sensor, misfire at two levels, and the fuel system. Misfire and fuel-system checks run continuously. The catalyst check and the upstream-sensor check run once per journey and not at the same time. An OBD fault that is confirmed on three consecutive journeys can light the warning lamp, if that fault is allowed to. A misfire that can damage the catalyst flashes the lamp. Three journeys with the fault absent put the lamp out.

The immobiliser is Verlog 4. The UCH and the engine computer exchange an authentication on the multiplex network before a start is authorised. After more than five failed attempts the engine computer stops authenticating and stays protected. The Renault text gives a recovery sequence for that state and, if the computer still will not unlock, tells the technician to contact Techline. The Mégane particulars call the immobiliser a third-generation coded system and say that replacing the computer has its own method. An S3000 from another car is not a plug-in exchange.

Not established

The exact SH705x device and a full connector pinout for the S3000 are not established; bench-connection pins are drawn in Sagem S3000 bench connection pinout.

Sources

  • Renault s.a.s., MR-366, petrol injection fault finding, S3000, program AD, Vdiag 4C and 54. Vehicles, composition, torque structure, dephaser, turbo pressure, injection order and the diagnostic procedure. Paraphrased. The document forbids copying.
  • Renault Mégane workshop particulars for multipoint Sagem S3000, as republished at MegManuel. Rev limits, the pedal tracks, the idle corrections and the returnless fuel system. Accessed 2026-11-13.
  • AutoTuner ECU compatibility list, PDF export dated 28 October 2026. Tool compatibility listing; microcontroller entry for Sagem S3000. Accessed 19 November 2026.