
Autronic SMC is a standalone or earlier programmable engine-management system. Early SMC sequential engine management. Autronic distinguishes pre-1996 and later Rev C loom arrangements; its archive says early looms only suit pre-1996 ECUs. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Processor
Autronic's product page (manufacturer documentation) gives the SMC microcontroller as a 16-bit Intel part running at 16 MHz. The exact part number is not stated in the sources checked.
Engine applications
The SMC is a universal ECU, not tied to specific vehicles. Per Autronic it suits port-injected spark-ignition engines without drive-by-wire throttle or feedback-controlled variable camshafts, including high-output supercharged or turbocharged engines, two-stroke engines, and engines with uneven firing sequences such as two- and four-cylinder V motorcycle engines and V6 car engines. Selectable cylinder counts are 1 to 8, 10, 12, 14 and 16, with full sequential injection for 2 to 8 cylinders. Hardware: eight injector drivers (selectable 4 A/1 A or 2 A/0.5 A), four open-collector ignition outputs without dwell control on the standard unit, one auxiliary output, fuel pump control, RS232 serial and a 36-way AMP connector. Positioned for high-performance motorsport; no engine codes are listed.
Wiring and pinout
Consult the Autronic SMC wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
J1 connector: manufacturer loom drawings
The 36-position J1 table, transcribed from Autronic's Type 1 pre-1996 single-relay diagram, revision 003 and universal Type 2 Rev C single-relay diagram, revision 005, with the pin 21 and 34 differences between the looms and the drawing wire colours, is on the Autronic SMC connector pinout page with a redrawn pin-index diagram (diagram redrawn by Tuning Wiki). The Type 1 loom is specified only for ECUs manufactured before 1996; the Type 2 drawing states it suits all SMC ECUs. Autronic's drawings call for calibration mode flag 11 to be set to 1 for the illustrated relay arrangement; the auxiliary and ignition output capabilities depend on the hardware and firmware fitted.
| J1 pin | Type 1 pre-1996 drawing | Type 2 Rev C universal drawing | Drawing wire colour |
|---|---|---|---|
| 1 | Injector 7 output | Injector 7 output | Grey/blue |
| 2 | Injector 6 output | Injector 6 output | Blue/black |
| 3 | Injector 4 output | Injector 4 output | Green/white |
| 4 | Injector 2 output | Injector 2 output | Orange/black |
| 5 | Injector 1 output | Injector 1 output | Pink/black |
| 6 | Coolant temperature input | Coolant temperature input | Pink |
| 7 | O2 input | O2 input | Blue |
| 8 | Reference trigger input | Reference trigger input | Green |
| 9 | Serial RX | Serial RX | Purple |
| 10 | Ignition 4 output | Ignition 4 output | Not specified |
| 11 | Ignition 2 output | Ignition 2 output | Not specified |
| 12 | Auxiliary output | Auxiliary output | Grey |
| 13 | ECU +12 V supply | ECU +12 V supply | Red |
| 14 | Injector 8 output | Injector 8 output | Blue/red |
| 15 | Injector 5 output | Injector 5 output | Green/yellow |
| 16 | Injector 3 output | Injector 3 output | Blue/white |
| 17 | Sensor ground | Sensor ground | Black |
| 18 | Throttle position input | Throttle position input | Orange |
| 19 | Throttle position supply | Throttle position supply | Red/white |
| 20 | Trigger supply | Trigger supply | Red/black |
| 21 | Serial I/O ground | Switch input | Black / green-orange respectively |
| 22 | Ignition 3 output | Ignition 3 output | Not specified |
| 23 | Diagnostic output (optional connection) | Diagnostic output (optional connection) | Not specified |
| 24 | Fuel pump output | Fuel pump output | Blue |
| 25 | +12 V / pump relay supply | +12 V / pump relay supply | Red |
| 26 | +12 V / auxiliary output supply | +12 V / auxiliary output supply | Pink/yellow |
| 27 | ECU ground | ECU ground | Black |
| 28 | ECU ground | ECU ground | Black |
| 29 | Ignition switch input | Ignition switch input | Red |
| 30 | Intake air temperature input | Intake air temperature input | White |
| 31 | Trigger ground | Trigger ground | Black |
| 32 | Cylinder pulse trigger input | Cylinder pulse trigger input | Yellow |
| 33 | Serial TX | Serial TX | Orange |
| 34 | Not labelled on Type 1 drawing | Serial I/O ground | Not specified / black respectively |
| 35 | Ignition 1 output | Ignition 1 output | Pink/white |
| 36 | Ignition output ground | Ignition output ground | Not specified |
Further information
Sources
- Autronic SMC product page. Manufacturer. Accessed 19 November 2026.
- SMC loom, pre-1996 Type 1, revision 003 and Type 2 Rev C, revision 005. Manufacturer drawings. Accessed 19 November 2026.