Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Simos 8.1 is a Siemens/Continental petrol engine-management variant documented by Audi on certain naturally aspirated 2.8 and 3.2 V6 FSI engines with Audi valvelift. These applications use a different air and load strategy from the supercharged 3.0 TFSI examples discussed on the Simos 8.4 and 8.5 page.

Processor

The Infineon TC1796 is the microcontroller listed for the neighbouring Simos 8.2 to 8.5 variants in AutoTuner's ECU compatibility export of 28 October 2026, which does not list Simos 8.1. A tool-vendor catalogue (Bitbox, seen in a search summary only; the page itself could not be retrieved) groups Simos 8.1x to 8.4x together as TC1796 bench-CAN units. The TC1796 for Simos 8.1 is therefore a single-source tool-vendor claim, not manufacturer documentation.

Documented applications and identification

Audi Self-Study Programme 411 identifies Simos 8.1 on its 2.8 FSI BDX and 3.2 FSI CALA V6 examples. Its tables describe both as naturally aspirated, with direct injection and variable valve timing. These are specific factory examples, not an exhaustive fitment list. Identify the actual ECU part and hardware numbers, software, calibration, engine, gearbox and installed equipment before selecting a definition or programming method.

The programme compares its Simos 8.1 engines with an earlier 3.2 FSI described as Simos 6D2. That comparison does not make the software or sensor layout interchangeable. The Simos 6 overview covers the earlier documented system. SSP 411 explicitly notes differences between its 2.8 A6 and 3.2 A5 electrical system overviews; use the exact engine and vehicle documentation when investigating signals.

Audi's SSP 603, page 13, also names Simos 8.1 for its A6 Avant '12 CHVA example. Aftermarket sources label some CHVA examples Simos 8.6; the reason for the differing suffix descriptions has not been established. See Simos 8.6 identification for the separate sources and identify the fitted ECU and software before selecting a file or protocol.

Valve lift and load control

In the SSP 411 engines, intake cam elements move between profiles for low and high valve lift. Audi describes a part-load range in which the throttle is nearly open and load is controlled using intake-cam timing and valve-lift strategy. After changeover to full lift, load is again controlled using the throttle and manifold pressure. Audi characterises this as a pressure, inlet-cam position and engine-speed based control strategy, not a simple pressure-and-speed model throughout the range.

This matters when interpreting logs. A wide throttle opening at a light or moderate load is not automatically a stuck throttle on this system, and throttle angle alone does not establish cylinder air charge. Compare engine speed and pedal with load, manifold pressure, valve-lift operating state and requested versus actual cam positions where accurately supported. The presence or spelling of a diagnostic channel does not establish its units, update rate or availability on another file. SSP 411, engine management.

Audi also describes coordinated lift changeover in SSP 411, page 61. For its partial-to-full-lift example, it describes retarding ignition, closing the throttle with a slight delay, moving intake and exhaust cams to new positions, and adjusting ignition again in relation to cam movement and manifold-pressure change. It gives an illustrative transition of approximately 300 ms in the 3,000–4,000 rpm range. These figures describe the training example, not universal switching thresholds, tuning values or evidence of exact behaviour on another software.

A brief ignition or throttle change near a confirmed lift transition is therefore not, by itself, proof of knock or an ECU fault. Where available, compare lift state, intake and exhaust cam targets and actual positions, throttle, pressure, ignition and knock corrections on the same time axis. Because the example is a short transient, check channel sampling intervals and any asynchronous updates before interpreting their sequence; a slow or staggered log may not resolve it. A requested cam position alone does not confirm that the lift mechanisms changed.

Intake and fuel details

SSP 411 says the charge motion from partial lift allowed the earlier intake-port charge-motion flaps to be omitted on its new engines. It also describes a variable intake manifold with a changeover function and position sender. These are different functions: eliminating the earlier charge-motion flaps does not mean that all intake changeover mechanisms or their diagnostics are absent.

The documented engines use direct petrol injection. Audi describes a low-pressure sender G410 and fuel metering valve N290 at the high-pressure pump, with high-pressure sensing in the system overview. It also describes a cold-start catalyst-heating mode with split direct-injection events and retarded ignition, followed by homogeneous operation in the other stated ranges. A split direct-injection event does not itself mean port injectors are installed. Check the actual engine and current workshop procedure rather than generalising the training example.

Interpreting manifold changeover and fuel metering

For the SSP 411 examples, Audi describes a two-stage variable manifold controlled by N156, with a vacuum reservoir in the manifold and position feedback from Hall sender G513. Its description says activating N156 releases the vacuum. This is a different function from the omitted charge-motion flaps and from intake-valve lift changeover. When investigating a repeatable power change, compare a correctly identified changeover request and G513 feedback where available, then follow the vehicle-specific diagnostic procedure for the valve, vacuum supply, actuator, feedback and mechanism. A command alone does not establish flap position, and position feedback does not independently measure airflow. Audi SSP 411, pages 50–52.

On the documented 2.8 and 3.2 valvelift engines, Audi describes a revised high-pressure pump with G410 and N290 integrated into it and a pressure-limiting valve in the pump. The programme notes that, unlike its earlier 3.2 FSI comparison, the revised pump delivers maximum feed when N290 is inactive and pressure rises to the limiting valve's discharge pressure. This is a system-description distinction, not a direction to disconnect the valve or a recommended pressure test. Interpret command and pressure using the actual pump and ECU documentation; check low-pressure supply, target, measured rail pressure and faults rather than assuming that the same electrical state has the same effect across generations. Follow current high-pressure fuel-system repair and safety procedures. Audi SSP 411, pages 53–55.

Calibration and diagnosis

Start with fault codes and the mechanical, electrical, fuel and intake baseline. In addition to ordinary lambda, fuel-pressure, ignition and knock-correction checks, compare the valve-lift or changeover state, intake-manifold changeover and intake/exhaust camshaft request and feedback when those channels are available. Record temperature, operating mode, rpm and load so a transition is not compared with steady-state data. A requested position or ECU-estimated torque is not a direct measurement of achieved cylinder filling or crankshaft torque.

The factory source describes the operating strategy, not performance-map addresses or a validated ignition and fuelling recipe. Verify map axes, units and function for the exact software and assess changes with appropriate logs. Do not assume that a Simos 8.4 or 8.5 boost, bypass or map-switching definition applies to 8.1.

For the factory-described actuator return signal, CALA/CALB implausible-signal codes and a scoped service bulletin, see V6 FSI valve-lift actuator diagnosis.

A ZIPtuning definition listing advertises an OLS project described as a DAMOS for an A6 2.8 FSI BDX with identifier 8T0907559B and software S8100C2000000. This is the seller's file-identification and format claim; the listing does not expose individual maps, axes or scaling and has not been validated here against an original read. Check exact software and inspect the definition rather than assuming that a similar part number proves compatibility.

Programming and recovery scope

A historical CMDFlash release note lists a Simos 8.1 A6 2.8 FSI example and describes a virtual-read and writing workflow for that product. A virtual read is a matching file supplied by a tool or database; it is not necessarily a complete physical read of the actual controller. Confirm the chosen tool's current coverage, file provenance, checksum handling and supported recovery method for the exact ECU before writing.

In its module 57 manual, page 49, PCMflash separately lists reading, writing and checksum functions for its 2.8 V6 Simos 8.1 coverage. This is a different product's claimed operation from CMDFlash's historical virtual read; neither listing proves its output is a complete memory image or guarantees coverage of every 8.1 ECU. Confirm current protocol, file scope and recovery for the exact unit.

Sources

  • Audi Self-Study Programme 411: 2.8 and 3.2 FSI engines with Audi valvelift, English edition. BDX/CALA Simos 8.1 examples, valve-lift operation, intake and fuel systems, load control and changeover. Training document; current workshop information remains authoritative. Accessed 17 November 2026.
  • Audi SSP 409: A4 2008. CALA 3.2 FSI and Simos 8.1 example. Accessed 17 November 2026.
  • CMDFlash V3.2.0.116 release note, 2013. Product-specific historical A6 2.8 FSI Simos 8.1 read/write coverage; current exact support and recovery must be checked. Accessed 17 November 2026.
  • ZIPtuning Audi A6 2.8 FSI BDX Simos 8.1 listing. Seller's software-specific OLS/DAMOS claim; contents not independently verified. Accessed 17 November 2026.
  • AutoTuner ECU compatibility list (PDF export dated 28 October 2026). Tool-vendor listing of ECU type and microcontroller for Simos 8.2 to 8.5; does not list 8.1. Accessed 19 November 2026.
  • Bitbox catalogue, Continental Simos 8 module listing (bitbox.ru). Tool-vendor grouping of Simos 8.1x to 8.4x as TC1796; seen in a search summary only, page not retrievable. Accessed 19 November 2026.